FRONT ANTI-TIPPERS
MODEL NOS. 2226 AND 1326
Installation, Assembly and Operating Instructions
The Front Anti-Tippers Kit (Right and Left)
consists of:
MODEL NO.
2226
1326
Size
1-inch
7/8-inch
DESCRIPTION
Lug Bolt
Locknut (fine thread)
Machine Screw
Locknut (coarse thread)
Anti-Tipper Triangular Assembly
Washer
QUANTITY
PART NOS.
Right
Left
1017846
1017847
1035967
1042413
1042414
1042412
4
4
2
2
2
4
2
Pair
NOTE: Check ALL parts for shipping damage. In case of
shipping damage, DO NOT use. Contact Carrier/Dealer
for further instruction.
Anti-Tipper Arm w/Bracket Clamps
SAFETY SUMMARY
INSTALLING FRONT ANTI-TIPPERS
(FIGURE 1)
The following recommendations are made for safe in-
stallation and adjustment of the Front Anti-tippers:
NOTE: Refer to the INSTALLATION WARNINGS in
the SAFETY SUMMARY of this instruction sheet.
GENERAL WARNINGS
DO NOT insta ll or use this kit without first re a ding
a nd unde rsta nding this instruc tion she e t. If you
a re una ble to unde rsta nd the Wa rnings, Ca utions
or Instructions, conta ct a hea lthca re professiona l,
de a le r or te c hnic a l pe rsonne l be fore a tte mpt-
ing to insta ll this kit - othe rwise , injury or da ma ge
ma y oc c ur.
1. Remove the locknuts and the lug bolts from the anti-
tipper bracket clamps.
2. Positiontheanti-tipperbracketclampoverthewheel-
chair frame behind the front caster as shown in FIG-
URE 1.
NOTE: Position the anti-tipper arm on the outside of
the wheelchair as shown in FIGURE 1.
INSTALLATION WARNINGS
Afte r ANY a djustme nts, re pa ir or se rvic e a nd BE-
FORE use , ma ke sure a ll a tta c hing ha rdwa re is
tighte ne d se c ure ly - othe rwise injury or da ma ge
ma y oc c ur.
3. Squeezebracketclampstogetherandinsertthebolts.
4. Installthelocknutsontothelugbolts. Tightensecurely.
5. Repeat STEPS 1-4 on the opposite side of the
wheelchair for the remaining anti-tipper.
6. Measure from the floor to the bottom of the wheels of
the triangular assembly.
Front a nti-tippe rs a re re c omme nde d by Inva c -
a re whe n using e le va ting le gre sts. Eve n though
a whe e lc ha ir is e quippe d with front a nti-tippe rs,
individua ls should be ta ught to e le va te le gre sts,
swing front riggings a side a nd/or flip up footpla tes
so the y a re out of the wa y BEFORE pla c ing fe e t
firmly on the floor whe n e nte ring or e xiting the
whe e lc ha ir. This will pe rmit individua ls to sta nd
c lose to front e dge of the se a t a nd lowe r him-
se lf/he rse lf we ll e nough ba c k onto the se a t.
7. Perform one (1) of the following:
TRIANGULAR ASSEMBLY 3/4-INCH FROM
FLOOR - Repeat STEPS 1-2 for the opposite tri-
angular assembly.
TRIANGULAR ASSEMBLY NOT 3/4-INCH
FROM FLOOR - Adjust the height of the triangular
assemblies.RefertoADJUSTINGFRONTANTI-TIP-
PERS in this instruction sheet.
Ensure Front Anti-Tippe rs a re a djuste d to the
sa me he ight - othe rwise the whe e lc ha ir ma y
tip to one side a nd injury or da ma ge ma y
oc c ur.
INSTALLATION CAUTION
When securing the front a nti-tippers to the wheel-
c ha ir fra me . DO NOT ove rtighte n the a tta c hing
ha rdwa re , othe rwise da ma ge to the whe e lc ha ir
fra me ma y oc c ur.
OVER
|
Indesit Washer IWC 6145 S User Manual
Intel Computer Hardware BOXDH55HC User Manual
Intel Computer Hardware PT800DB User Manual
Intellinet Network Solutions Network Router 523431 User Manual
JAI Digital Camera TMC 4200GE User Manual
Jotul Fan F 100 USA User Manual
Kenwood DVD Player DV 5050M User Manual
KitchenAid Refrigerator KBFS25EVMS3 User Manual
Kramer Electronics Music Mixer VA 14 User Manual
Kramer Electronics Satellite Radio 602T User Manual