KDC-X995
KDC-BT948HD
CD-RECEIVER
INSTRUCTION MANUAL
Before reading this manual, click the button below to check the latest edition and the
modified pages.
Check the latest edition
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from
your new CD-receiver.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the
space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for
information or service on the product.
Model KDC-X995/ KDC-BT948HD Serial number
US Residents Only
Register Online
Register your Kenwood product at www.Kenwoodusa.com
© 2010 Kenwood Corporation All Rights Reserved.
11FLIP_IM330_Ref_K_en_00
Audio Adjustments
Audio Control
Preset Equalizer curve Select
Manual Equalizer Control
Listening Position Selection
Listening Position Fine Adjustments
Dual Zone System
40
44
48
Basic Operations of remote control
Appendix
58
60
About Audio file
iPod/iPhone that can be connected to this unit
About PANDORA® internet radio
About USB device
About “KENWOOD Music Editor”
About the Cell-Phone
About Satellite Radio tuner (Optional)
Menu List
City list
DSP Setup
Car Type Selection
Speaker Setting
Car Type Fine Adjustments
X’Over Setting
Audio Preset Memory
Audio Preset Recall
Accessories/ Installation Procedure
Connecting Wires to Terminals
Installation/Removing the Unit
Troubleshooting Guide
67
68
69
71
74
Bluetooth Setup
Easy pairing function
Bluetooth Setting
Registering Bluetooth device
Registering PIN Code
Selecting the Bluetooth device You Wish to
Connect
Specifications
Deleting a Registered Bluetooth device
Downloading the Phone Book
Adding a Voice Dialing Command
Setting a Voice Command for Category
SMS (Short Message Service)
54
Downloading the SMS
SMS (Short Message Service)
Satellite Radio Tuner Control (Optional) 56
Basic Operation
Satellite Radio Setting
Category and Channel Search
Preset Memory
Preset Tuning
Channel Scan
Direct Access Tuning
English
|
3
Before use
Lens Fogging
2WARNING
When you turn on the car heater in cold weather,
dew or condensation may form on the lens in the
CD player of the unit. Called lens fogging, this
condensation on the lens may not allow CDs to play.
In such a situation, remove the disc and wait for the
condensation to evaporate. If the unit still does not
operate normally after a while, consult your Kenwood
dealer.
To prevent injury or fire, take the following
precautions:
To prevent a short circuit, never put or leave any
metallic objects (such as coins or metal tools) inside
the unit.
Do not use this unit before canceling
Demonstration mode!
This unit is initially set on the Demonstration mode.
When using this unit for the first time, cancel the
Demonstration mode. Refer to <Before Using> (page
7).
Notes
• If you experience problems during installation,
consult your Kenwood dealer.
• When you purchase optional accessories, check with
your Kenwood dealer to make sure that they work
with your model and in your area.
• Characters that conform to ISO 8859-1 can be
displayed.
How to reset your unit
If this unit or the connected unit (auto disc changer,
etc.) fails to operate properly, press the Reset button.
The unit returns to factory settings when the Reset
button is pressed.
• The Radio Data System feature won’t work where
the service is not supported by any broadcasting
station.
Reset button
• In this document, the description indicator will
light means a status is displayed. Refer to <Basic
Operation> (page 30) for the details of the status
display.
• The illustrations of the display and the panel
appearing in this manual are examples used to
explain more clearly how the controls are used.
Therefore, what appears on the display in the
illustrations may differ from what appears on the
display on the actual equipment, and some of the
illustrations on the display may be inapplicable.
Cleaning the Unit
If the faceplate of this unit is stained, wipe it with a
dry soft cloth such as a silicon cloth.
If the faceplate is stained badly, wipe the stain off with
a cloth moistened with neutral cleaner, then wipe it
again with a clean soft dry cloth.
¤
• Applying spray cleaner directly to the unit may affect its
mechanical parts. Wiping the faceplate with a hard cloth or
using a volatile liquid such as thinner or alcohol may scratch
the surface or erases characters.
Unit and Faceplate Terminals
• To prevent deterioration, do not touch the terminals
of the unit and faceplate with your fingers.
• If the terminals on the unit or faceplate get dirty,
wipe them with a clean soft dry cloth.
|
4
KDC-X995/ KDC-BT948HD
Handling CDs
• Do not touch the recording surface of the CD.
• Do not stick tape etc. on the CD, or use a CD with
tape stuck on it.
• Do not use disc type accessories.
• Clean from the center of the disc and move
outward.
• When removing CDs from this unit, pull them out
horizontally.
• If the CD center hole or outside rim has burrs,
use the CD only after removing the burrs with a
ballpoint pen etc.
CDs that cannot be used
• CDs that are not round cannot be used.
• CDs with coloring on the recording surface or CDs
that are dirty cannot be used.
• This unit can only play the CDs with
.
This unit may not correctly play discs which do not
have the mark.
• You cannot play a CD-R or CD-RW that has not
been finalized. (For the finalization process refer to
your CD-R/CD-RW writing software, and your CD-R/
CD-RW recorder instruction manual.)
• 3 inch CD cannot be used. Attempt to insert using
an adapter can cause malfunction.
English
|
5
Component names and functions
5
4
3
6
2
1
AUX
14
10
13
9
12
8
11
7
1
8
[SRC] button
Release button
To drop the faceplate down to open and CD can be
To turn on this unit and select the Source (press the
inserted or ejected (press the button).
button).
To turn off this unit (press the button at least 1
second).
2
[MENU] button
To select a song or set functions. See <Menu List
9
[
4
] / [¢] buttons
To select station, song and setting items. (press the
button).
3
[DISP] button
To change display item (press the button).
[VOL] knob
10 [38] button
To start or interrupt playback for CD, audio file, and
iPod (press the button).
4
To adjust volume (turn the knob).
To select menu list item (turn and press the knob). See
<Menu List Operation> (page 7) for details.
Enters Play mode Menu (press the button at least 1
second).
11 [SCRL] button
The displayed text scrolls (press the button).
To enter “Clock & Date” settings when Clock Display
mode is selected in the Display Setting mode (press
the button).
5
[SEARCH MODE] button
To enter Search mode (iPod), move between folders
(Audio file), etc. For more details, see operations of
each source described in page 8 or later.
12 Display window
13 [ ] button
6
Microphone
To enter Bluetooth mode (press the button).
To enter Bluetooth easy pairing mode (press the
button at least 1 second). See <Easy pairing function>
The microphone for the hands free phone is supplied.
When your voice cannot be recognized due to the
low microphone volume or noises in the vehicle,
adjust the microphone settings by <Bluetooth
14 USB Terminal
A USB device or an iPod can be connected.
7
Auxiliary Input Terminal
Portable audio device can be connected with the
mini-plug (3.5 mm (1/8”) ø).
• Use the mini-plug cable which is stereo type and does not
have any resistance.
|
6
KDC-X995/ KDC-BT948HD
General operation
Before Using
Menu List Operation
The basic operating procedure for using this
function is described below. The individual function
items are covered in the operating procedures.
Exit of the Demonstration Mode
Turn off the demonstration mode when you use it
for the first time after installation.
1
Select the source
Pressing the [SRC] button repeatedly switches
source.
Function items vary from source to source. For a list
1
2
Press the [VOL] knob to quit the demonstration
mode when the messages “To cancel Demo
press the volume knob” are displayed (approx. 15
seconds).
Turn the [VOL] knob to select “YES” and press the
[VOL] knob.
2
3
Enter Menu List mode
Press the [MENU] button.
Select the setting item
⁄
Turn the [VOL] knob and press it when the
desired item is displayed.
Repeat the operation until your desired setup item
is selected.
• Demonstration mode can also be cancelled in “DEMO
Mode” of Menu List mode. Refer to <Demonstration mode
✍ Press the [MENU] button to return to the
previous item.
Common Operation
Operation example:
Power and source select
Turns the power ON by pressing the [SRC]
button.
4
1[VOL]
2[VOL]
3
2
Music
3
2
PlayLists
My
When the power is ON, select a source.
• SRC Select mode 1: Pressing the [SRC] button
each time switches between sources.
HD Radio (“HD RADIO”) ➜ USB (“USB”) or iPod
(“iPod”) ➜ Pandora (“Pandora”) ➜ CD (“CD”) ➜
Auxiliary input (“AUX”) ➜ Standby (“STANDBY”)
➜ HD Radio...
Best 25
1
1
Artists
Albums
3[MENU]
[MENU]
4
1 sec.
Play Mode
• SRC Select mode 2: Press the [SRC] button and
then turn the [VOL] knob. To determine the
selected source, press the [VOL] knob.
Keeping pressing the [SRC] button for at least 1
second turns the power OFF.
In this manual, the above selection is indicated as
Select “Music” > “Playlists” > “My Best 25”.
4
5
Make a setting
• When the “
” icon is displayed (at the
PUSH
right edge of the display)
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
⁄
• When the “
” icon is not displayed
PUSH
Press the [4] or [¢] button to select a
setting value.
• Auxiliary input source is initially set to “OFF”. Set “Built in
• When an optional accessory is connected, the source name
for each device appears.
• When connection of the iPod is recognized, the source
display changes from “USB” to “iPod”.
Exit Menu List mode
Press the [MENU] button for at least 1 second to
return to the first hierarchy. Press the [MENU]
button in the first hierarchy to exit the Menu
List mode.
Volume
Turning the [VOL] knob adjusts the sound
volume.
⁄
• You cannot set the item with the “ ” icon displayed.
English
|
7
iPod/iPhone Operation
SRC MENU VOL DISP
SEARCH MODE
KCA-iP102 (optional
accessory) is required to
connect an iPod.
Do not use the KCA-
⁄
iP102 with an extension
4
38
¢
SCRL
cord.
4
Select a song
Basic Operation
Operation type
Move between items
Select an item
Operation
Turn the [VOL] knob.
Press the [VOL] knob.
Press the [DISP] or [SCRL] button to scroll
up or down by a page.
Press the [DISP] or [SCRL] button for at
least 1 second to continuously scroll up or
down at high speed. Press the button again
to stop scrolling.
Playing iPod
• Connect an iPod
When connected, the source is switched
automatically and a song starts playing.
High Speed Search
• Select iPod source
Press the [SRC] button.
Select the “iPod” display.
Return to previous item
Return to Top menu
Press the [MENU] button.
Press the [MENU] button for at least 1
second.
Song Select
Press the [4] or [¢] button.
Fast Forwards or Fast Backwards
Hold down the [4] or [¢] button.
✍ For example: Searching by Artist name.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Music” > “Artists” > Artist name > Album
name > Song title
Pause and Play
Press the [38] button to pause or resume
playback.
Cancelling Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
Remove iPod
Select a source other than iPod and Pandora, and
the iPod can be removed safely.
⁄
• The unit memorizes the position where you have
found a song in the Search mode. When you enter the
Menu List mode after searching a song, the memorized
position is displayed. Press the [MENU] button for at least
1 second to move to the first hierarchy, select a Menu
item, and set it’s parameters.
• Characters which cannot be displayed are left blank. If
non of the characters can be displayed, the browse item
name and digits are displayed.
Selecting a song by browsing iPod
Display
Items
“Music”
“Playlists”
“Artists”
Playlists
Artists
“Albums”
“Songs”
Albums
Songs
Items
Playlists
Artists
Albums
Songs
Display
“PLIST***” Podcasts
“ART***”
“ALB***”
“PRGM***”
Items
Display
“Podcasts”
“Genres”
“Composers”
Podcasts
Genres
Composers
“PDCT***”
“GEN***”
“COM***”
Genres
Composers
1
2
Select iPod source
Enter Menu List mode
Press the [MENU] button.
3
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Music”.
|
8
KDC-X995/ KDC-BT948HD
Play Mode
iPod Setting
You can select a Play Mode, such as Random play
and Repeat play.
You can select following iPod Setting items.
1
2
Select iPod source
1
2
Select iPod source
Enter Menu List mode
Press the [MENU] button.
Enter Play Mode Menu
Press the [VOL] knob for at least 1 second.
✍ You can also select from “Play Mode” in Menu
List mode.
3
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings”.
3
Select the Play Mode
Turn the [VOL] knob.
4
Select the setting item
Turn the [VOL] knob and press it when the
desired item is displayed.
Display
Overview
“iPod by Hand”
When set to“ON”, allows you to operate iPod
with the control on the iPod.
“ON”/ “OFF”
When set to“ON”, plays the music in the folder
randomly.
“ON”/ “OFF”
When set to“ON”, plays all songs in iPod
randomly.
Display
“Settings”
“Skip Search”
Overview
Sets the ratio of skip performed with <Skip
“0.5%”/ “1%”/ “5%”/ “10%”
Deletes the registered My Playlist.
Refer to <Deleting a Song from the Playlist>
(page 12) for the operation.
“Folder Random”
“All Random”
“Delete My
Playlist”
“ON”/ “OFF”
When set to“ON”, plays the music repeatedly.
“ON”/ “OFF”
“One”/ “All” ➜ “Yes”/ “No”
“File Repeat”
(
: Factory setting)
5
6
Make a setting
4
5
Make a setting
Press the [4] or [¢] button.
• When the “
” icon is displayed (at the
PUSH
right edge of the display)
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
Exit Play Mode Menu
Press the [MENU] button.
• When the “
” icon is not displayed
PUSH
Remarks
• All Random
Press the [4] or [¢] button to select a
setting value.
• The time required to turn on the all random function
may become longer depending on the number of songs
in iPod.
• Turning on the all random function changes the iPod
browse item to “Songs”. This browse item will not be
changed even if the all random function is turned off.
• If the browse item is changed to search for music while
the all random function is on, the all random function is
turned off and the songs in the browse item are played
at random.
Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
⁄
Changing the setting of one reflects the other.
• iPod by Hand (iPod Control by Hand Mode)
Allows you to operate iPod with the control on the iPod.
⁄
• In the iPod Control by Hand Mode, iPod cannot be
operated using this unit.
• This mode is not compatible with music information
display. The display will show “iPod by Hand Mode”.
• iPod can be operated when it conforms to the iPod
control function.
English
|
9
iPod/iPhone Operation
Selecting the Search mode
Direct Search
You can select the most suited search method for
the desired song from 4 types of the Search mode.
You can quickly search the desired song by
specifying its Search item (artist, album, etc.) and
character.
Normal playing
1
2
Select iPod source
Display
Overview
Press the [SEARCH MODE] button.
“Direct Search”
You can quickly search the desired song by
specifying its Search item (artist, album, etc.)
and character.
3
Enter Direct Search mode
Turn the [VOL] knob and press it when the
Searches for music of the same artist or genre
as the one being played.
desired item is displayed.
Select “Direct Search”.
“Related Search”
Registers a song to My Playlist and play it.
4
Select the Search item
Turn the [VOL] knob and press it when the
desired Search item is selected.
“Recall My Playlist”
“Delete My Playlist”
“Register My P-list”
Display
Items
Playlists
Artists
Albums
Songs
Display
“PODCASTS”
“GENRES”
Items
Podcasts
Genres
Browsing
“PLAYLISTS”
“ARTISTS”
“ALBUMS”
“SONGS”
Display
“Direct Search”
Overview
“COMPOSERS” Composers
You can quickly search the desired song by
specifying its Search item (artist, album, etc.)
and character.
You can select an alphabetic character from
the list in the Search item (artist, album, etc.)
selected now.
The number of songs to be skipped is
determined by the ratio of the total number of
songs in the list which is selected now.
Registers a song to My Playlist.
5
6
Select the character to be searched for
“Alphabet Search”
“Skip Search”
Operation type
Operation
Move between items
Select an item
Move to the next column
Turn the [VOL] knob.
Press the [VOL] knob.
Press the [4] or [¢] button.
Up to 3 characters can be entered.
Determine the selected character
Turn the [VOL] knob and press it when the
desired item is displayed.
“Register My P-list”
Select “DONE”.
1
Select iPod source
Pressing the [SRC] button repeatedly switches
source.
Select the “iPod” display.
Start search. When search is completed, the music
search mode is selected again at the selected
character position.
After this step, you need to browse. See step 4 of
select a song.
2
3
4
Enter Search mode
Press the [SEARCH MODE] button.
Select the Search mode
Turn the [VOL] knob.
Cancelling the Direct Search
Press the [SEARCH MODE] button.
Start the search mode
Press the [VOL] knob.
⁄
• Characters that can be entered are alphabetical
characters (A to Z), numerical characters(0 to 9), and “ * ”.
• “ * ”indicates characters other than alphabetical and
numerical characters. You cannot enter any more
characters when entering “ * ” in the first character
position.
Cancelling Search mode
Press the [SEARCH MODE ] button.
• If the first character string begins with an article “a”, “an”,
or “the” in the Direct Search mode, it is searched for in
defiance of the article.
|
10 KDC-X995/ KDC-BT948HD
Related Search
Alphabet Search
Searches for music of the same artist or genre as the
one being played.
You can select a song by alphabet. This function
searches songs whose name contain the specified
character(s) in the list of the selected Search item
(artist, album, etc).
1
2
Play the music in iPod
Press the [SEARCH MODE] button.
1
2
Select iPod source
3
Enter Related Search mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Enter browsing mode
Press the [MENU] button.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Music” > item.
Select “Related Search”.
4
Select the Search item
Turn the [VOL] knob and press it when the
3
4
Enter Alphabet Search mode
desired Search item is selected.
Turn the [VOL] knob fast. Or, press the [SEARCH
MODE] button and turn the [VOL] knob to
select “Alphabet Search”.
Display
Searches music
“Search Artist”
“Search Album”
Displays the album of the same artist.
Displays music in the album in which the one
being played is included.
Search for item
“Search Genre”
Displays the artist of the same genre.
Operation type
Operation
“Search Composer” Displays the album including music created by the
same Composer.
Select the character
Press the [DISP] or [SCRL] button./
Turn the [VOL] knob.
Press the [VOL] knob.
Press the [MENU] button.
Select an item
Return to previous item
After this step, you need to browse. See step 4 of
select a song.
After this step, you need to browse. See step 4 of
select a song.
Cancelling the Related Search
Press the [SEARCH MODE] button.
Cancelling the Alphabet Search
Press the [MENU] button.
⁄
• Related search cannot be performed while playing the
Podcast.
⁄
• When the music being played has no information on
browsing items or no music was found, “Not Found” is
displayed.
• The time of search by alphabet may become long
depending on the number of songs or items in iPod.
• If the first character string begins with an article “a”, “an”,
or “the” in the Alphabet Search mode, it is searched for in
defiance of the article.
English
|
11
iPod/iPhone Operation
Skip Search
My Playlist
You can scroll up or down according to the number
of the selected Search items so that you can quickly
switch the display position.
Allows you to register your favorite songs in the
Playlist of this unit. You can register up to 10 songs
in the Playlist.
1
2
Select iPod source
Registering Songs in the Playlist
Enter browsing mode
1
2
Play the song you want to register
Press the [MENU] button.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Music” > item.
Press the [SEARCH MODE] button.
3
Register the song
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Register My Playlist”.
“## Stored (Registration number)” is displayed.
3
4
Press the [SEARCH MODE] button.
Enter Skip Search mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Skip Search”.
⁄
• Make a Playlist from the songs stored in one iPod. If you
attempt to register a song stored in a different iPod,
”No Information” appears and then ”Delete My Playlist”
appears. Select “Yes” to delete the Playlist when you want
to remake it.
5
Search for item
Operation type
Move between items
Select an item
Operation
Turn the [VOL] knob.
Press the [VOL] knob.
Press the [DISP] or [SCRL] button.
Keep pressing the button for 3 seconds or
longer skips songs at 10% irrespective of
the setting.
• The song displayed in the Music Search mode can be
registered in the same manner. For how to use the music
search function, refer to <Selecting a song by browsing
• If you attempt to register the eleventh song, ”Memory
Full” appears and you cannot register it accordingly. To
register the song, delete an unnecessary song.
• Do not register Podcasts. Songs you do not want to
register may be registered, or playback may not be
carried out correctly.
Skip Search
Sets the ratio of skip
performed
Return to previous item
Press the [
4] or [¢] button.
Press the [MENU] button.
After this step, you need to browse. See step 4 of
select a song.
Playing the Song in the Playlist
1
2
Press the [SEARCH MODE] button.
Cancelling the Skip Search
Enter My Playlist mode
Turn the [VOL] knob and press it when the
Press the [SEARCH MODE] button.
⁄
desired item is displayed.
Select “Recall My Playlist”.
•
9).
3
Play the song in the Playlist
Turn the [VOL] knob and press it when the
desired item is displayed.
Select the song you want to play.
⁄
• Turning ACC OFF or the power OFF cancels the My
Playlist mode.
• The ending of a song may be cut unless the song has a
silence of 1 second or longer at the end.
• Random play cannot be performed during playback of a
song in the Playlist.
Deleting a Song from the Playlist
Press the [SEARCH MODE] button.
1
|
12 KDC-X995/ KDC-BT948HD
2
3
Enter Delete Playlist mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Delete My Playlist”.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select ”Delete One” or ”Delete All”.
Selecting “Delete All” moves to step 5 and all songs
are deleted.
4
5
Turn the [VOL] knob and press it when the
desired item is displayed.
Select the song you want to delete.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select ”Yes”.
“Completed” is displayed.
⁄
• You can also delete all songs from the Playlist by
selecting “Delete My Playlist” described in <iPod Setting>
• If you connect the different iPod from one registered to
My Playlist, “Delete One” and “Delete All” will not appear
and all songs be deleted.
English
|
13
PANDORA® Operation
SRC MENU VOL
DISP
KCA-iP102 (optional
accessory) is required to
connect an iPhone.
Do not use the KCA-
⁄
iP102 with an extension
4
38
¢
SCRL
cord.
Basic Operation
Station Search
You can select the station you want to listen to from
your station list.
Listening to PANDORA®
• Connect an iPhone
1
2
Select Pandora source
Connecting the iPod with the Pandora
application running will switch the source
automatically to start broadcasting from the
registered station.
Enter Menu List mode
Press the [MENU] button.
3
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Stations”.
• Select Pandora source
Press the [SRC] button.
Select the “Pandora” display.
✍ If the Pandora application is not running, “Check
Device” is displayed.
A station list is displayed.
4
Switch between the station list display mode.
Press the [4] or [¢] button.
⁄
Display
Overview
• To use the Pandora source, set “Pandora Source”in
• If no station has been selected, broadcasting does not
start.
“Alphabet Sort”
“Date Sort”
Stations are displayed in alphabetical order..
Stations are displayed in date order.
5
6
Select a station
Turn the [VOL] knob and press it when the
desired item is displayed.
Pause and Play
Press the [38] button to pause or resume
playback.
Exit Menu List mode
Press the [MENU] button for at least 1 second,
Thumbs up
and then press it again briefly.
Press the [DISP] button for at least 1 second.
“
” is displayed.
Thumbs down
Press the [SCRL] button for at least 1 second.
Bookmark Registration
You can register the current song information or
artist information in Bookmark.
“
” is displayed.
Song skip
Press the [¢] button.
✍ If the skip count limit specified by Pandora is
exceeded, “No skips remaining” is displayed.
1
2
Select Pandora source
Enter Menu List mode
Press the [MENU] button.
3
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Bookmarks” > “Bookmark Song” (to
register song information) or “Bookmark Artist”
(to register artist information).
Remove iPhone
Select a source other than Pandora and iPod, and
the iPod can be removed safely.
|
14 KDC-X995/ KDC-BT948HD
4
Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
Deletion of Station
You can delete registered station information.
1
2
Select Pandora source
⁄
• This unit allows you to bookmark songs and/or artists in
your personalized PANDORA® account. The bookmarks
will not be available for review on the unit but will be
available in your PANDORA® account.
Enter Menu List mode
Press the [MENU] button.
3
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Station Delete”.
Search and New Station Registration
4
Switch between the station list display mode.
Press the [4] or [¢] button.
You can search for the desired station by specifying
its character. You can register the displayed station
as a new station.
Display
Overview
“Alphabet Sort”
“Date Sort”
Stations are displayed in alphabetical order.
Stations are displayed in date order.
1
2
Select Pandora source
Enter Menu List mode
Press the [MENU] button.
5
6
Turn the [VOL] knob and press it when the
desired item is displayed.
Select the station you want to delete.
3
Turn the [VOL] knob and press it when the
desired item is displayed.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select ”YES”.
Select “New Stations”.
4
Select the character to be searched for
“Completed” is displayed.
Operation type
Operation
Cancelling the Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
Move between items
Select an item
Move to the next column
Return to previous item
Turn the [VOL] knob.
Press the [VOL] knob.
Press the [4] or [¢] button.
Press the [MENU] button.
Up to 3 characters can be entered.
5
Determine the selected character
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “DONE”.
Start search.
After this step, you need to Search. See step 4 of
<Station Search> (page 14) to select a station.
Cancelling Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
⁄
• Characters that can be entered are alphabetical
characters (A to Z), numerical characters(0 to 9), and
other symbols (“ & ”, “ . ”, “ ‘ ”, “ - ”, “ # ” ,“ + ”, “ ! ”, “ $ ”, “ “ ”).
English
|
15
USB device Operation
When connecting the
SEARCH MODE
SRC MENU VOL
DISP
USB device, usage of the
CA-U1EX (MAX : 500 mA)
(option) is recommended.
4
38
¢
SCRL
Basic Operation
File Search
Selecting the file you want to listen to from the
device being played now.
Playing USB device
• Connect a USB device
When connected, the source is switched
USB device
automatically and a song starts playing.
Display
Items
“Music”
Folder or file name list.
• Select USB source
Press the [SRC] button.
Select the “USB” display.
Music Editor media
Display
“Music”
“Playlists”
“Artists”
“Albums”
“Songs”
“Genres”
Items
Moving to the next folder
Press the [SEARCH MODE] button.
Playlists
Artists
Albums
Songs
Song Select
Press the [4] or [¢] button.
Fast Forwards or Fast Backwards
Hold down the [4] or [¢] button.
Genres
1
2
Select USB source
⁄
• No sound is output while playing audio file.
Enter Menu List mode
Press the [MENU] button.
Pause and Play
Press the [38] button to pause or resume
playback.
3
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Music”.
Remove USB device
Select a source other than the USB, and the USB
device can be removed safely.
4
Select a file
Operation type
Move between items
Select an item
Operation
Turn the [VOL] knob.
Press the [VOL] knob.
High Speed Search
Press the [DISP] or [SCRL] button to scroll
up or down by a page.
Press the [DISP] or [SCRL] button for at
least 1 second to continuously scroll up or
down at high speed. Press the button again
to stop scrolling.
Return to previous item
Return to Top menu
Press the [MENU] button.
Press the [MENU] button for at least 1
second.
✍ For example: Searching for ¡".
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Music” > 1 > 2 > ¡"
|
16 KDC-X995/ KDC-BT948HD
USB Setting
1
2
You can select following USB Setting items.
¡"
¡#
¡!
1
2
Select USB source
Enter Menu List mode
Press the [MENU] button.
Cancelling Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
3
Turn the [VOL] knob and press it when the
desired item is displayed.
⁄
Select “Settings”.
• When you search a song in the File Search mode, the
unit memorizes the position of the song being played
after the search. To set a different Menu item after
searching a song, press the [MENU] button for at least 1
second to move to the first hierarchy.
4
Select the setting item
Turn the [VOL] knob and press it when the
desired item is displayed.
Display
Overview
“Settings”
“Skip Search”
Play Mode
Sets the ratio of skip performed with <Skip
“0.5%”/ “1%”/ “5%”/ “10%”
You can select a Play Mode, such as Random play
and Repeat play.
(
: Factory setting)
1
2
Select USB source
5
6
Make a setting
Press the [4] or [¢] button.
Enter Play Mode
Press the [VOL] knob for at least 1 second.
✍ You can also select from “Play Mode” in Menu
List mode.
Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
3
Select the Play Mode
Turn the [VOL] knob.
⁄
Changing the setting of one reflects the other.
Display
Overview
“File Scan”
When set to“ON”, plays the intro of the music in
the folder successively.
• This operation is effective only for the files registered in
the database created with KENWOOD Music Editor.
“ON”/ “OFF”
“Folder Random”
“All Random”
When set to“ON”, plays the music in the folder
randomly.
“ON”/ “OFF”
When set to“ON”, plays all songs in the USB
device randomly.
“ON”/ “OFF”
“File Repeat”
When set to“ON”, plays the music repeatedly.
“ON”/ “OFF”
“Folder Repeat”
When set to“ON”, plays the music in the folder
repeatedly.
“ON”/ “OFF”
(
: Factory setting)
4
5
Make a setting
Press the [4] or [¢] button.
Exit Play Mode
Press the [MENU] button.
English
|
17
USB device Operation
Function of remote control
Skip Search
Direct Music Search
You can scroll up or down according to the number
of the selected Search items so that you can quickly
switch the display position.
Searching the music by entering the file number.
1
2
3
Enter Direct Music Search mode
Press the [DIRECT] button on the remote
control.
1
2
Select USB source
Enter File Search mode
Press the [MENU] button.
Enter the music number
Press the number buttons on the remote
control.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Music” > item.
Search the music
Press the [4] or [¢] button.
3
4
Enter Skip Search mode
Press the [SEARCH MODE] button.
Cancelling Direct Music Search
Press the [DIRECT] button.
Search for music
Operation type
Move between items
Select an item
Operation
Turn the [VOL] knob.
Press the [VOL] knob.
⁄
• Direct Music Search cannot be performed during playing
of “Music Editor” media, Random play, or scan play.
Skip Search
Press the [DISP] or [SCRL] button.
Keep pressing the button for 3 seconds or
longer skips songs at 10% irrespective of
the setting.
Sets the ratio of skip
performed
Press the [
4] or [¢] button.
Return to previous item
Press the [MENU] button.
After this step, see step 4 of <File Search> (page 16)
to select a song.
Cancelling the Skip Search
Press the [SEARCH MODE] button.
⁄
• This operation is effective only for the files registered in
the database created with KENWOOD Music Editor.
|
18 KDC-X995/ KDC-BT948HD
Music CD/ Audio file Operation
Fast Forwards or Fast Backwards
Hold down the [4] or [¢] button.
Release MENU VOL DISP
SEARCH MODE
⁄
• No sound is output while playing audio file.
Pause and Play
Press the [38] button to pause or resume
playback.
SRC 4 38
¢
SCRL
Function of Internal CD source
Basic Operation
Music Search
Drop open the faceplate
Press the Release button.
Selecting the music you want to listen to from the
disc being played now.
⁄
Display
“Music”
Overview
• Push the faceplate on the left side, and return it to its
Track list (Music CD) / Folder or file name list
(Audio file)
former position.
Disc play
• A disc inserted.
1
2
Select CD source
Enter Menu List mode
Press the [MENU] button.
When inserted, the source is switched
automatically and a song is starts playing.
When a CD is inserted, the “CD-IN” indicator
is ON.
3
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Music”.
4
Search for music
Operation type
Move between items
Select an item
Operation
Turn the [VOL] knob.
Press the [VOL] knob.
High Speed Search
Press the [DISP] or [SCRL] button to scroll
up or down by a page.
• Select CD source
Press the [SRC] button.
Select the “CD” display.
Press the [DISP] or [SCRL] button for at
least 1 second to continuously scroll up or
down at high speed. Press the button again
to stop scrolling.
Press the [MENU] button.
Press the [MENU] button for at least 1
second.
Disc ejection
Press the [0] button.
Return to previous item
Return to Top menu
Moving to the next folder
Press the [SEARCH MODE] button.
Cancelling Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
⁄
• This operation can be performed only for the Audio file.
Song Select
Press the [4] or [¢] button.
English
|
19
Music CD/ Audio file Operation
“Track Repeat”
“Disc Repeat”
When set to“ON”, plays the music repeatedly.
“ON”/ “OFF”
When set to“ON”, plays the music on the disc
repeatedly.
Play Mode
You can select a Play Mode, such as Random play
and Repeat play.
“ON”/ “OFF”
1
2
Select CD source
(
: Factory setting)
Enter Play Mode
4
5
Make a setting
Press the [VOL] knob for at least 1 second.
✍ You can also select from “Play Mode” in Menu
List mode.
Press the [4] or [¢] button.
Exit Play Mode
Press the [MENU] button.
3
Select the Play Mode
Turn the [VOL] knob.
Basic Operation of Disc Changer
(Optional)
Music CD source
Display
Overview
“Track Scan”
When set to“ON”, plays the intro of the music on
the disc successively.
“ON”/ “OFF”
When set to“ON”, plays the music on the disc
randomly.
“ON”/ “OFF”
Select CD changer source
Press the [SRC] button.
Select the “CD CHANGER” display.
“Disc Random”
“Track Repeat”
Moving to the next disc
Press the [SEARCH MODE] button.
When set to“ON”, plays the music repeatedly.
“ON”/ “OFF”
Song Select
Press the [4] or [¢] button.
(
: Factory setting)
Audio file source
Fast Forwards or Fast Backwards
Hold down the [4] or [¢] button.
Display
Overview
“File Scan”
When set to“ON”, plays the intro of the music on
the folder successively.
“ON”/ “OFF”
When set to“ON”, plays the music on the disc
randomly.
“ON”/ “OFF”
Pause and Play
Press the [38] button to pause or resume
playback.
“Folder Random”
“All Random”
When set to“ON”, plays all songs in the disc
randomly.
“ON”/ “OFF”
“File Repeat”
When set to“ON”, plays the music repeatedly.
“ON”/ “OFF”
“Folder Repeat”
When set to“ON”, plays the music on the folder
repeatedly.
“ON”/ “OFF”
(
: Factory setting)
Disc changer source (Optional)
Display
Overview
“Track Scan”
When set to“ON”, plays the intro of the music on
the disc successively.
“ON”/ “OFF”
“Disc Random”
When set to“ON”, plays the music on the disc
randomly.
“ON”/ “OFF”
“Magazine Random” When set to“ON”, plays the music in the disc
changer randomly.
“ON”/ “OFF”
|
20 KDC-X995/ KDC-BT948HD
Function of remote control
Direct Music Search
Searching the music by entering the track number.
1
2
3
Enter Direct Music Search mode
Press the [DIRECT] button on the remote
control.
Enter the music number
Press the number buttons on the remote
control.
Search the music
Press the [4] or [¢] button.
Cancelling Direct Music Search
Press the [DIRECT] button.
⁄
• Direct Music Search cannot be performed during playing
of Random play or scan play.
Function of disc changer with remote control
Direct Disc Search
Searching the disc by entering the disc number.
1
2
3
Enter Direct Disc Search mode
Press the [DIRECT] button on the remote
control.
Enter the disc number
Press the number buttons on the remote
control.
Search the disc
Press the [FM] or [AM] button.
Cancelling Direct Disc Search
Press the [DIRECT] button.
⁄
• Direct Disc Search cannot be performed during Random
play or scan play.
• Input “0”to select disc 10.
English
|
21
HD Radio™ Tuner Operation
3
4
Enter Preset Memory mode
Turn the [VOL] knob and press it when the
desired item is displayed.
SRC MENU VOL
SEARCH MODE
Select “List & Memory”.
Select the number to put in the memory
Turn the [VOL] knob and press [VOL] knob for
at least 2 seconds when the desired item is
displayed.
4
¢
Select a preset number.
Display
“List & Memory”
“-1”
Overview
This HD Radio receiver enables:
Preset number 1. (FM/ AM/ Mixed)
Preset number 2. (FM/ AM/ Mixed)
“-2”
“-6”
Preset number 6. (FM/ AM/ Mixed)
Preset number 18. (FM)
“-18”
⁄
• You can register up to 18 FM stations and 6 AM stations.
Selecting “Mixed” for “Tuner Preset Type” allows you to
register up to six stations including FM, AM, and another
Satellite Radio Tuner regardless of the selected source.
Basic Operation
Selecting HD Radio source
Press the [SRC] button.
Select the “HD RADIO” display.
Cancelling the Preset Memory mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
Selecting the Receiving Band
1. Enter Menu List mode
Press the [MENU] button.
2. Turn the [VOL] knob and press it when the
desired item is displayed.
Select “FM” or “AM”.
Auto Memory Entry
Putting stations with good reception in the memory
automatically.
Selecting the Receiving station or channel
Press the [4] or [¢] button.
During reception of stereo stations the “ST”
indicator is light up.
✍ Details of the station selecting in operation are
set in the “Seek Mode” of <HD Radio™ Setting>
1
2
3
Select the radio band you wish to store in the
preset memory
Enter Menu List mode
Press the [MENU] button.
Enter Auto Memory Entry mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “Auto Memory”.
Station Preset Memory
4
Open Auto Memory Entry
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “YES”.
When 18 stations (FM) or 6 stations (AM) that can
be received are put in the memory, auto memory
entry closes.
Putting a station in the memory.
1
Select the radio band and tune in a desired
radio station you wish to store in the preset
memory
2
Enter Menu List mode
Press the [MENU] button.
|
22 KDC-X995/ KDC-BT948HD
5
6
Make a setting
Press the [4] or [¢] button.
⁄
• This setting can be made when “Type Normal”is selected
Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
Preset Tuning
Recalling the stations in the memory.
Function of remote control
1
2
Select the radio band
Direct Access Tuning
Enter Menu List mode
Press the [MENU] button.
Tuning in a desired radio station by entering the
frequency.
3
Select a desired station in the memory
Turn the [VOL] knob and press it when the
desired item is displayed.
1
2
Select the radio band
Enter Direct Access Tuning mode
Press the [DIRECT] button.
“– – – –” is displayed.
Select “List & Memory” > Preset number.
3
Select Tuning item
Press the [DIRECT] button.
Pressing the [DIRECT] button each time switches
HD Radio™ Setting
You can select following HD Radio Setting items.
the following tuning items as follows.
1
2
Select the HD Radio source
Items
Display
“– – – –”
“HD –”
—
Enter Menu List mode
Press the [MENU] button.
Frequency
Channel
3
Turn the [VOL] knob and press it when the
desired item is displayed.
Cancelling Direct Access Tuning
Select “Settings”.
4
5
Enter the frequency or Channel
Press the number buttons.
Example of frequency input:
4
Select the setting item to adjust
Turn the [VOL] knob and press it when the
desired item is displayed.
Desired frequency
92.1 MHz (FM)
810 kHz (AM)
Press button
[9], [2], [1]
[8], [1], [0]
Display
Overview
“Settings”
“Seek Mode”
Selects the tuning mode of the radio.
“Auto1”: Automatic search for a station.
“Auto2”: Search in order of the stations in the
Preset memory.
Tune in to the entered frequency or Channel
Press the [4] or [¢] button.
Cancelling Direct Access Tuning
Press the [DIRECT] button on the remote
control.
“Manual”: Normal manual tuning control.
“Auto Memory” Memorizes 18 stations (FM) or 6 stations (AM)
with good reception automatically.
Refer to <Auto Memory Entry> (page 22)
“Receive Mode” Sets the receive mode of the HD Radio receiver.
“Auto”: Automatically tunes to analog broadcast
when there is no digital broadcast.
“Digital”: Digital broadcasts only.
“Analog”: Analog broadcasts only.
“TAG Memory” Displays the tag memory usage of HD Radio
receiver. Up to 50 tags can be registered to
this unit.
“0”/“50”
“Tagging”
Turns ON / OFF the tag memory function of
HD Radio receiver.
“OFF”/“ON”
(
: Factory setting)
English
|
23
HD Radio™ Tuner Operation
iTunes Tagging
Using an iTunes Tagging enabled HD Radio receiver
you can tag your music. When you hear a song you
enjoy on your local HD Radio station, you only have
to press the [SEARCH MODE] button. The song’s
information will then be saved on this unit. The
saved songs will then show up in a playlist called
“Tagged” in iTunes the every next time you sync
your iPod to your computer. So then you just need
to click and then easily buy and download the song
you were tagging directly from the Apple iTunes
Music Store.
1
Saves song’s information
Press the [SEARCH MODE] button.
“
” will be indicated on the display when song
TAG
information can be registered.
⁄
when using this function.
• Up to 50 TAGs (song’s information) can be registered to
this unit. When iPod is connected, the TAG information
registered to this unit is transferred to the connected
iPod.
• The memory usage can be checked by selecting “TAG
|
24 KDC-X995/ KDC-BT948HD
English
|
25
Operation of hands-free phoning
Receiving a Call
SRC MENU VOL
SEARCH MODE
DISP
Answering a Phone Call
Press the [VOL] knob.
⁄
• The following operations disconnect the line:
- Insert a CD.
- Connect a USB device.
4
38
¢
• The name of the calling party is displayed if it has already
been registered in the Phone Book.
Getting Started
Rejecting an Incoming Call
Press the [ ] or [SRC] button.
Before use the cell-phone, you need to connect cell-
phone to this unit.
⁄
During a Call
• For details on the Bluetooth cell-phone with the hands-
Disconnecting a Call
Press the [ ] or [SRC] button.
1
2
Enter easy pairing mode
Press the [ ] button for at least 1 second.
Switching to the Private Mode
Press the [38] knob.
Switches between Private talk (“PRIVATE”) and
Hands-free talk each time this button is pressed.
“Searching” is displayed.
Search for the Bluetooth device.
When search is completed, “Finished” is displayed.
⁄
3
4
Select a cell-phone name
• Depending on the type of your cell-phone, switching
to the private talk mode may select the source that was
used before commencing the hands-free connection.
If this happens, the source cannot be switched back to
the hands-free talk mode by operating this unit. Operate
your cell-phone to return to the hands-free talk mode.
Turn the [VOL] knob and press it when the
desired item is displayed.
Input the PIN code
1. Turn the [VOL] knob and press it when the
desired item is displayed.
Select the digit.
2. Turn the [VOL] knob to select the numbers,
and then press the [VOL] knob.
Adjusting the Voice Volume during a Call
Turn the [VOL] knob.
Call Waiting
5
6
Transmit the PIN code
If “Pairing Success” is displayed, registration is
completed.
When “Confirm Phone” is displayed, confirm
connection with a cell-phone operation.
Answering Another Incoming Call with the
Current Call Suspended
1
2
Press the [VOL] knob.
Turn the [VOL] knob and press it when the
desired item is displayed.
The receiver is connected to a cell-phone, with
“HF Connect” displayed, and exits the easy
pairing mode.
Select “ANSWER”.
Answering another Incoming Call after
Terminating the Current Call
⁄
Press the [ ] or [SRC] button.
Continuing the Current Call
1
2
Press the [VOL] knob.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “REJECT”.
|
26 KDC-X995/ KDC-BT948HD
Answering the Waiting Call after Terminating
the Current Call
Press the [ ] or [SRC] button.
Speed Dialing (Preset Dial)
1
Enter Bluetooth mode
Press the [ ] button.
Switching between the Current Call and Waiting
2
Select the preset dial mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Call
Press the [VOL] knob.
Each pressing of this knob switches the calling
Select “Preset call”.
party.
3
Select the number you want to recall from the
memory
Other Functions
Turn the [VOL] knob and press it when the
desired item is displayed.
Select preset number.
Phone number is displayed.
Clearing the Disconnection Message
Press the [ ] button.
“HF Disconnect” disappears.
4
5
Exit the preset dial mode
Press the [MENU] button.
Making a Call
Make a call
Press the [VOL] knob.
1
Enter Bluetooth mode
Press the [ ] button.
⁄
2
Select a dialing method
Turn the [VOL] knob and press it when the
• You need to register the preset dial number. Refer to
desired item is displayed.
Display
Overview
“Preset Call”
“Phonebook”
Calling a number in the preset.
Selecting the character to be searched for the
phone book.
“Outgoing Calls” Calling a number in the outgoing call list.
“Incoming Calls” Calling a number in the incoming call list.
“Missed Calls”
Calling a number in the missed calls list.
“Number Dial” Making a call by entering phone number.
“Voice Recognize” Make a Voice Dialing Call.
Operation method of each mode is described
below.
3
Exit the dialing method mode
Press the [ ] button.
English
|
27
Operation of hands-free phoning
4
Make a call
Press the [VOL] knob.
Calling a Number in the Phone Book
1
Enter Bluetooth mode
Press the [ ] button.
⁄
• The outgoing call list and the incoming call list, and the
missed call list are the lists of calls originated from and
received at this unit. They are not the ones stored in the
cell-phone memory.
2
Select the Phone Book mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Phonebook”.
Dial a Number
3
4
Select the character to be searched for
Operation type
Operation
1
Enter Bluetooth mode
Press the [ ] button.
Move to the next character. Turn the [VOL] knob.
Move to the next row.
Determine the selected
character.
Press the [4] or [¢] button.
Press the [VOL] knob.
2
Select the number dial mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select the name
Select “Number Dial”.
Operation type
Move to the next phone
number.
Operation
Turn the [VOL] knob.
3
Enter a phone number
Operation type
Operation
Select the numbers.
Move to the next digit.
Delete the last digit.
Turn the [VOL] knob.
Determine the selected phone Press the [VOL] knob.
number.
Press the [
Press the [
¢
] button.
] button.
4
✍ Switching between Display Modes
Press the [DISP] button.
Pressing this button each time switches between
name and telephone number.
• Press the number ([1] – [0]), #([FM]), *([AM]), or
+([¢]) button on the remote controller.
✍ To erase the entered phone number digit
by digit:
5
Make a call
Press the [VOL] knob.
Press the [4] button on the remote
controller.
⁄
4
Make a call
• During search, a non-accent character such as “u”is
searched for instead of an accent character such as “ü”.
• Press the [VOL] knob.
• Press the [DIRECT] button on the remote
controller.
Calling a Number in the Call log
⁄
1
Enter Bluetooth mode
Press the [ ] button.
• You can input max 25 digits.
2
Select the call log mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Outgoing Calls”, “Incoming Calls”, or
“Missed Calls”.
3
Select a name or phone number
Turn the [VOL] knob and press it when the
desired item is displayed.
✍ Switching between Display Modes
Press the [DISP] button.
Pressing this button each time switches between
name and telephone number.
|
28 KDC-X995/ KDC-BT948HD
Make a Voice Dialing Call
Registering to the Preset Dial Number
List
1
2
Enter Bluetooth mode
Press the [ ] button.
1
Select the phone number you wish to register
Select the phone number with reference to the
following:
Select voice recognition mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Voice Recognize”.
3
4
“PB Name?” is displayed.
When a beep is heard, say the name within 2
seconds.
2
3
Enter Preset Memory mode
Press the [VOL] button for at least 1 second.
“PN Type” is displayed.
When a beep is heard, say the category name
Select the Preset number to put in the
memory
within 2 seconds.
Turn the [VOL] knob and press it for at least 1
second when the desired item is displayed.
Select preset number.
5
Make a call
Press the [VOL] knob.
✍ This step is the same as step 4 of the procedure
28). You can make a call or select a category.
4
Determine the Preset number to put in the
memory
Turn the [VOL] knob and press it when the
desired item is displayed.
⁄
• If your voice cannot be recognized, a message is
displayed. Pressing the [VOL] knob allows you to retry
• Both the name and category require registration of
a voice tag. Refer to <Setting a Voice Command for
Exit the Preset Memory mode
Press the [MENU] button.
Display of Phone Number type
(category)
• Audio sound is not output during voice recognition.
The category items in the Phone Book are displayed
as follows:
Display
Information
“GENERAL”/“
”
General
“HOME”/“
“OFFICE”/“
“MOBILE”/“
“OTHER”/“
”
Home
Office
Mobile
Other
”
”
”
English
|
29
Display Settings
Display Setting
SRC MENU VOL
DISP
You can select following Display Setting items.
1
Select the source
Pressing the [SRC] button repeatedly switches
source.
2
3
Enter Menu List mode
Press the [MENU] button.
4
¢
SCRL
Enter Display Setting mode
Turn the [VOL] knob and press it when the
Basic Operation
desired item is displayed.
Select “Settings” > “DISP & ILLUMI”.
Switching display
Press the [DISP] button.
4
Select the setting item to adjust
Turn the [VOL] knob and press it when the
desired item is displayed.
Mode Display Type
5-line display mode Displays 4 to 5 lines of text.
3-line display mode Displays 2 to 3 lines of text.
iPod-like display Displays like iPod. (iPod source only)
mode
Display
Overview
“Settings”
Spectrum analyzer Displays a line of text and the spectrum analyzer.
display mode
Clock display mode Displays the clock.
Display off mode Turns off the display and illumination..
“DISP & ILLUMI” Making Display and Illumination settings.
“Display Select” Selecting and customizing the Display type.
“Color Select” Selecting the Illumination Color of the panel.
Refer to <Illumination Color Selection>
⁄
“DISP & ILLUMI If this unit is not operated at least 5 seconds
• When the 5-line display mode is selected, the status (ON/
OFF indicator of each function) can be displayed on the
first line, and the icon of the currently selected source and
the text information title can be displayed on the left side
by the following <Customization of 5-line Display Mode
operation.
OFF”
with“DISP”selected, the display turns off.
During a setup mode, the display will not turn
off even if 5 seconds lapse.
Selecting “DISP & ILLUMI” turns off the
illumination and display together.
“DISP”/ “DISP & ILLUMI”
“Display
Dimmer”
Reduces the display Illumination brightness.
“Auto”: Dims the illumination in conjunction
with the Light switch of the vehicle.
“Manual1”: Dims the illumination constantly.
“Manual2”: Dims the illumination darker than
Manual1.
Status display: Select “Settings” > “DISP & ILLUMI” > “Display
Select” > “Status”
Side display: Select “Settings” > “DISP & ILLUMI” > “Display
Select” > “Side Select”
• When “Display off mode”is selected, you can select only
“Type Select” for “Display Select”.
“OFF”: Does not dim the illumination.
“Contrast”
“DISP N/P”
Adjusting the display contrast.
“1” - “5” - “12”
Switches the panel display between positive
or negative.
Text scroll
Press the [SCRL] button.
The displayed text scrolls.
“POSI1”/ “POSI2”/ “NEGA1”/ “NEGA2”
“TEXT Scroll” Specifies whether the text is scrolled
automatically.
“Auto”/ “Once”/ “OFF”
“ILLUMI
Dimmer”
Reduces the key Illumination brightness.
“Auto”: Dims the illumination in conjunction
with the Light switch of the vehicle.
“Manual1”: Dims the illumination constantly.
“Manual2”: Dims the illumination darker than
Manual1.
“OFF”: Does not dim the illumination.
|
30 KDC-X995/ KDC-BT948HD
“ILLUMI Effect” Sets whether the key illumination brightness is
changed in conjunction with the key operation.
“OFF”/ “ON”
“ILLUMI MSC Sets whether the key illumination color is
SYNC”
changed in conjunction with the sound volume.
“OFF”/ “ON”
(
: Factory setting)
5
6
Make a setting
• When the “
” icon is displayed (at the
PUSH
right edge of the display)
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
• When the “
” icon is not displayed
PUSH
Press the [4] or [¢] button to select a
setting value.
Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
English
|
31
Display Settings
Text Display Selection
In HD Radio source
Customization of 5-line Display Mode
& 3-line Display Mode & iPod-like
Display Mode
5-line display mode
Frequency (“Frequency”)
Station name (“Station Name”)
Song Title (“Song Title”)
Album name (“Album Name”)
Artist name (“Artist Name”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
You can customize the display of the 5-line display
mode, 3-line display mode, and iPod-like display
mode.
Blank (“Blank”)
1
Select the source
Pressing the [SRC] button repeatedly switches
3-line display mode
source.
Frequency (“Frequency”)
Station name (“Station Name”)
Artist name & Song Title (“Artist
name/Title”)
Artist name & Album name
(“Artist/Album”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
2
3
Enter Menu List mode
Press the [MENU] button.
Blank (“Blank”)
Enter Display Setting mode and Select the
5-line display mode, 3-line display mode or
iPod-like display mode.
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “DISP & ILLUMI” > “Display
Select” > “Type Select” > 5-line display mode
or 3-line display mode or iPod-like display
mode.
In USB/ iPod/ Audio file source
5-line display mode
Song title (“Song Title”)
Album name (“Album Name”)
Artist name (“Artist name”)
Folder name (“Folder name”)
File name (“File name”)
Play time (“P-Time”)
Play time bar (“Time Bar”) : iPod
only
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
4
Select the setting item to adjust
Turn the [VOL] knob and press it when the
desired item is displayed.
Blank (“Blank”)
3-line display mode
Display
Setting
Ttitle & Artist (“Ttitle/ Artist”)
Album & Artist (“Album/ Artist”)
Folder name (“Folder name”)
File name (“File name”)
Play time bar (“Time Bar”) : iPod
only
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
“Display Select”
“Type Select” Selects from 5-line display mode, 3-line display
mode, or iPod-like display mode.
“Side Select” Sets the source display.
Text/ Icon/ Disappear
“Text Select” Sets the text display.
1. Turn the [VOL] knob to select the text
display part
Play time (“P-Time”)
Blank (“Blank”)
iPod-like display mode
Song title (“Song Title”)
Album name (“Album Name”)
Artist name (“Artist name”)
Blank (“Blank”)
The selected text display part blinks.
2. Press the [4] or [¢] button to
select the text
In Pandora source
“Status”
Sets the Status display of the 5-line display mode.
Appear/ Disappear
5-line display mode
(
: Factory setting)
Song title (“Song Title”)
Album name (“Album Name”)
Artist name (“Artist name”)
Play time (“P-Time”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
5
6
Make a setting
Press the [4] or [¢] button.
Blank (“Blank”)
Exit Menu List mode
Press the [MENU] button for at least 1 second,
3-line display mode
and then press it again briefly.
Ttitle & Artist (“Ttitle/ Artist”)
Album & Artist (“Album/ Artist”)
Play time (“P-Time”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Blank (“Blank”)
|
32 KDC-X995/ KDC-BT948HD
• If all characters cannot be displayed while playing with iPod,
the file number in the list is displayed.
In Music CD source
Disc title (“Disc title”)
Track title (“Track title”)
Play time (“P-Time”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Information
Music title
Folder name
File name
Display
“TITLE***”
“FLD***”
“FILE***”
Blank (“Blank”)
In Auxiliary input source
Source name (“Source Name”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Blank (“Blank”)
Customization of Spectrum Analyzer
Display Mode
In Standby
You can customize the display of the Spectrum
analyzer display mode.
Source name (“Source Name”)
Date (“Date”)
Clock (“Clock”)
Blank (“Blank”)
1
Select the source
Pressing the [SRC] button repeatedly switches
In Disc changer source (Optional)
source.
Disc title (“Disc title”)
Track title (“Track title”)
Play time (“P-Time”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
2
3
Enter Menu List mode
Press the [MENU] button.
Blank (“Blank”)
Enter the Display Setting mode and select the
Spectrum analyzer display mode
Turn the [VOL] knob and press it when the
desired item is displayed.
In SIRIUS/ XM source (Optional)
5-line display mode
Channel Name (“Channel Name”/ Category Name (“Category Name”
Select “Settings” > “DISP & ILLUMI” > “Display
Select” > “Type Select” > Spectrum analyzer
display mode.
“CHANNEL NAME”)
Song Title (“Song Title”/“SONG
TITLE”)
Artist name (“Artist name”/
“ARTIST NAME”)
Composer name (“Composer
name”) : SIRIUS only
/“CATEGORY”)
Channel Number (“Channel
Number”/“CHANNEL NUMBER”)
Spectrum analyzer & Clock
(“Speana/Clock”)
Date (“Date”)
Blank (“Blank”)
4
Select the setting item to adjust
Turn the [VOL] knob and press it when the
desired item is displayed.
Display
“Display Select”
Setting
3-line display mode
Channel Name (“Channel Name”/ Channel Number (“Channel
“CHANNEL NAME”) Number”/“CH NUMBER”)
Artist name & Song Title (“Artist/ Spectrum analyzer & Clock
Song”/“NAME/TITLE”) (“Speana/Clock”)
Category Name (“Category Name” Date (“Date”)
/“CATEGORY”)
“Type Select” Selects the Spectrum analyzer display mode.
“Graphic
Select”
Changes the display of the Spectrum analyzer
display mode.
“Text Select” Sets the text display.
Blank (“Blank”)
5
6
Make a setting
Press the [4] or [¢] button.
⁄
• If the selected display item does not have any information,
alternative information is displayed.
Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
• Some items cannot be selected depending on the display
type and row.
• When selecting “Folder name”while playing with iPod,
names will be displayed depending on currently selected
browsing items.
• If the iPod Control by Hand Mode is set to on while playing
the iPod, “iPod by Hand Mode” is displayed.
English
|
33
Display Settings
Customization of Clock Display Mode
Illumination Color Selection
You can customize the display of the Clock Display
mode.
Selecting the Illumination Color of the panel.
1
Enter Menu List mode
Press the [MENU] button.
1
Select the source
Pressing the [SRC] button repeatedly switches
2
Enter Illumination color selection mode
Turn the [VOL] knob and press it when the
desired item is displayed.
source.
2
3
Enter Menu List mode
Press the [MENU] button.
Select “Settings” > “DISP & ILLUMI” > “Color
Select”.
Enter Display Setting mode and Select the
Clock Display
3
4
Select the place where you want to set the
Illumination Color
Turn the [VOL] knob and press it when the
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “DISP & ILLUMI” > “Display
Select” > “Type Select” > Clock Display mode.
desired item is displayed.
Display
“All”
“Display”
“Key”
Place
Display and key
Display
4
Select the setting item to adjust
Turn the [VOL] knob and press it when the
desired item is displayed.
Key
Display
Setting
Select the Illumination Color
Turn the [VOL] knob and press it when the
desired item is displayed.
“Display Select”
“Type Select” Selects the Clock Display mode.
“Graphic
Select”
Switches between single and dual clock.
Select the color from “Variable Scan”/ “Color1”—
“Color 24”/ “User”.
5
6
Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
Creating “User” color
You can create your original color during the
selection from “Color1”— “Color24.”
The color you created can be called when you
select “User”.
1. Press the [VOL] knob for at least 1 second.
Enter the detail color adjustment mode.
2. Set the color.
Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
Operation type
Operation
To select the color to adjust. Press the [4] or [¢] button.
(red, green, or blue)
To adjust color.
(Range: 0 – 9)
Turn the [VOL] knob.
3. Press the [VOL] knob.
Exit the detail color adjustment mode.
5
Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
|
34 KDC-X995/ KDC-BT948HD
Auxiliary Input Display Setting
Selecting the display when changing to Auxiliary
input source.
1
Select the AUX source
Pressing the [SRC] button repeatedly switches
source.
Select the “AUX” display.
2
3
Enter Menu List mode
Press the [MENU] button.
Enter Auxiliary input display setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “AUX Name Set”.
4
5
Select the Auxiliary input display
Turn the [VOL] knob.
Select “AUX”, “DVD”, “PORTABLE”, “GAME”, “VIDEO”, or
“TV”
Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
⁄
• The Auxiliary input display can be set only when the
built-in auxiliary input or the auxiliary input of optional
KCA-S220A is used. On the KCA-S220A, “AUX EXT” is
displayed by default.
• AUX source is initially set to “OFF”. Before display setting,
set “Built in AUX” described in <Initial Settings> (page 38)
to “ON”.
English
|
35
Clock and Other Functions
4
5
Set the Clock & Date setting items
Turn the [VOL] knob and press it when the
desired item is displayed.
Release MENU VOL
Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
SRC 4
¢
Clock Adjustment
You can adjust the clock.
Clock & Date display type setting
1
Enter Menu List mode
Press the [MENU] button.
Sets the display type of the clock and calendar.
1
Enter Menu List mode
Press the [MENU] button.
2
Enter Clock adjustment mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “Clock & Date” > “Clock
Adjust”.
✍ When “Clock display mode” is selected in the
Display Setting mode, pressing the [SCRL] button
allows you to select “Clock & Date” directly.
2
3
Enter the Clock & Date setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
3
4
Adjusting Clock
1. Turn the [VOL] knob to set the hours.
2. Press the [¢] button.
3. Turn the [VOL] knob to set the minutes.
4. Press the [VOL] knob.
Select “Settings” > “Clock & Date”.
Select the desired Clock & Date setting item
Turn the [VOL] knob and press it when the
desired item is displayed.
Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
Display
Overview
“Settings”
“Clock & Date”
“Clock Adjust”
Sets the clock.
Refer to <Clock Adjustment> (page 36)
Sets the two cities to be displayed when
dual clock mode is selected for“Graphic
“City Select”
“Time Synchronized” Synchronizing the Radio Data System
station time data and this unit’s clock.
“OFF”/ “ON”
“Summer Time”
Advances the clock one hour when set
to ON.
“OFF”/ “ON”
“Sub Clock Adjust” Adjusts the time difference caused by
summer time.
“-1h”/ “0h”/ “+1h”
“Date Adjust”
Sets the date.
Refer to <Date Adjustment> (page 37)
“Date Mode Select” Sets the date display mode.
7 types
(
: Factory setting)
|
36 KDC-X995/ KDC-BT948HD
Date Adjustment
Dual clock city setting
You can adjust the date.
You can select cities for two clocks.
1
Enter Menu List mode
Press the [MENU] button.
1
Enter Menu List mode
Press the [MENU] button.
2
Enter Clock adjustment mode
Turn the [VOL] knob and press it when the
desired item is displayed.
2
Enter City Select mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Settings” > “Clock & Date” > “Date
Adjust”.
Select “Settings” > “Clock & Date” > “City
Select”.
3
4
Adjusting Date
1. Turn the [VOL] knob to adjust the month.
3
4
5
Select the city (Home or Sub) display part
Turn the [VOL] knob.
2. Press the [¢] button.
Set cities for Home/ Sub
Press the [4] or [¢] button.
3. Turn the [VOL] knob to adjust the day.
4. Press the [¢] button.
Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
5. Turn the [VOL] knob to adjust the year.
6. Press the [VOL] knob.
Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
⁄
• To display the clocks of two cities, select dual clock
mode for “Graphic Select” described in <Customization
• Time of Sub City is automatically derived from Home
time.
When summer time systems are different between
Home and Sub cities, adjustment can be done by
referring to “Sub Clock Adjust” of <Clock & Date display
Remarks
• City Select
Set a time zone for your area as “Home”. When you set a
time zone for different area to the “Sub”, clocks for two
time zones can be displayed on the clock display. See
English
|
37
Clock and Other Functions
“Built in AMP”
Selecting“OFF”turns off the built-in amplifier.
Turning off the built-in amplifier improves the
quality of the sound from Preout.
“OFF”/ “ON”
DSI (Disabled System Indicator) of the unit blinks
when the faceplate is removed.
“OFF”/ “ON”
Updates the firmware. The update information
will be posted on the following URL as
necessary.
Initial Settings
You can select following Initial Setting items.
1
Select the Standby
Pressing the [SRC] button repeatedly switches
“DSI”
source.
Select the “STANDBY” display.
“F/W Update”
2
3
Enter Menu List mode
Press the [MENU] button.
Enter Initial Setting mode
Turn the [VOL] knob and press it when the
(
: Factory setting)
5
6
Make a setting
• When the “
right edge of the display)
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
• When the “
Press the [4] or [¢] button to select a
setting value.
desired item is displayed.
Select “Initial Settings”.
” icon is displayed (at the
PUSH
4
Select the setting item to adjust
Turn the [VOL] knob.
” icon is not displayed
PUSH
Display
Overview
“Initial Settings”
“Tuner Preset Type” You can select a preset type.
“Type Normal”: Memorizes one station for each
Exit Menu List mode
Press the [MENU] button for at least 1 second,
and then press it again briefly.
preset button in each band (FM/ AM/ SR1 –
SR4/ XM1 – XM4).
“Type Mixed”: Memorizes one station for each
preset button regardless of the selected band
(FM/ AM) and another Satellite Radio Tuner.
Demonstration mode Setting
“SRC Select”
“Beep”
Sets the source selection method.
“Settings 1”/ “2”
Setting the operation check sound (beep sound)
ON/OFF.
Turning the demonstration mode ON/OFF.
1
Enter Menu List mode
Press the [MENU] button.
“OFF”/ “ON”
“Menu Language” You can select the display language for the
Menu list item.
“English”/ “Français”/ “Español”
“Pandora Source” When this is set to ON, Pandora source can be
selected.
2
Enter Demonstration mode setting
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “DEMO Mode”.
“ON”: Allows you to select the Pandora source
by connecting a Pandora-compliant iPhone.
“OFF”: Disable Pandora source selection.
When this is set to ON, AUX source can be
selected.
“ON”: Allows AUX source to be selected. Use
this setting when the built-in AUX terminal
is connected to the external equipment all
the time.
3
4
Set the Demonstration mode
Turn the [VOL] knob and press it when the
desired item is displayed.
“Built in AUX”
Select “ON” or “OFF”.
Exit Menu List mode
Press the [MENU] button.
“OFF”: Disable AUX source selection. Use this
setting when the built-in AUX terminal is
not used.
“Forced CD-DA” Sets the method for reading CD.
“Settings 1”: Automatically distinguishes
between audio file disc and music CD when
playing disc.
“Settings 2”: Forces playing as music CD.
|
38 KDC-X995/ KDC-BT948HD
Theft Deterrent Faceplate
The faceplate of the unit can be detached and
taken with you, helping to deter theft.
Removing the Faceplate
1
Press the Release button.
Drop open the faceplate.
2
Drawing the faceplate to left side pull it to
forward and remove it.
¤
• The faceplate is a precision piece of equipment and can
be damaged by shocks or jolts.
• Keep the faceplate in its faceplate case while detached.
• Do not expose the faceplate (and the faceplate case) to
direct sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of water
splashing.
Reattaching the Faceplate
3
Align the shaft on the unit with the depression
on the faceplate.
4
Push the faceplate in until it clicks.
The faceplate is locked in place, allowing you to
use the unit.
English
|
39
|