National Instruments Network Card 370620B 01 User Manual

PCI/PXI GIGABIT ETHERNET ADAPTERS  
INSTALLATION GUIDE  
National Instruments gigabit Ethernet adapters are based on the  
Intel 82540-compatible Ethernet controller.  
This document explains how to install and troubleshoot the Ethernet drivers  
for your PCI/PXI board. Some boards also contain additional functionality  
(for example, GPIB). Refer to the documentation that came with your kit to  
install the software for the other functionality.  
Installing Your PXI Board  
Complete the following steps to install the Ethernet adapter:  
1. Shut down Windows, if it is running, by clicking Start»Shut Down.  
2. Turn off your PXI or CompactPCI chassis. Keep the chassis plugged  
in so that it remains grounded as you install the adapter.  
3. Remove the filler panel from a PXI peripheral bus master slot. The  
adapter requires a bus master slot to take advantage of the onboard  
DMA and Ethernet controllers. All PXI chassis and most CompactPCI  
chassis contain only bus master slots. Refer to your chassis  
documentation to verify you are using a bus master slot.  
4. Touch a metal part on your chassis to discharge any static electricity  
that might be on your clothes or body.  
5. Insert the adapter into the selected bus master slot. Use the  
injector/ejector handle to fully inject the device into place.  
6. Screw the front panel of the adapter to the front panel mounting rail  
of the PXI or CompactPCI chassis.  
Installing Your PCI Board  
Complete the following steps to install the Ethernet adapter:  
1. Shut down Windows, if it is running, by clicking Start»Shut Down.  
2. Turn off the computer and unplug the power cord.  
National Instruments™, NI™, NI-488.2™, and ni.com™ are trademarks of National Instruments Corporation. Product and  
company names mentioned herein are trademarks or trade names of their respective companies. For patents covering  
National Instruments products, refer to the appropriate location: Help»Patents in your software, the patents.txt file  
on your CD, or ni.com/patents.  
December 2002  
370620B-01  
ni.com  
© 2002 National Instruments Corp. All rights reserved.  
 
The cable length is limited to 100 m.  
The adapter must be connected to a compatible link partner,  
preferably set to auto-negotiate speed and duplex.  
The PCI-8231/8232 and PXI-8231/8232 automatically  
accommodate either MDI or MDI-X connections. The  
auto-MDI-X feature allows you to directly connect two adapters  
without using a crossover cable.  
2. To configure Ethernet for your adapter, continue with the procedure  
specific to your operating system outlined later in this guide.  
Install the Drivers  
Follow the installation instructions for your operating system. The adapter  
works with the following operating systems:  
Windows Me/98  
Windows 2000/XP  
Windows NT 4.02  
Windows Me/98  
To install the drivers, complete the following steps:  
1. Shut down, then power off the computer as shown in the following  
figure.  
© National Instruments Corporation  
3
PCI/PXI Gigabit Ethernet Adapters Installation Guide  
 
 
2. Install the hardware and cables, then power on the computer as shown  
in the following figure.  
3. Install the PCI-PCI bridge driver.  
Windows automatically detects the new hardware.  
Follow the prompts in the Wizard. Select the recommended options  
when given a choice. If Windows asks where to search for a new  
driver, clear all checkboxes and click Next.  
4. Install the Windows Me/98 Ethernet drivers.  
Windows Me  
Windows automatically detects the new hardware and displays an Add  
New Hardware Wizard window, as shown in the following figure.  
Insert the PCI/PXI Gigabit Ethernet Adapters CD-ROM and follow  
the instructions. Choose the Recommended options when given a  
choice and click Next.  
Windows 98  
Windows automatically detects the new hardware and displays an Add  
New Hardware Wizard window, as shown in the following figure.  
Insert the PCI/PXI Gigabit Ethernet Adapters CD-ROM and follow  
the instructions presented. Choose the Recommended options when  
given a choice.  
PCI/PXI Gigabit Ethernet Adapters Installation Guide  
4
ni.com  
 
If Windows asks where to search for a new driver, make sure the box  
next to CD-ROM Drive is checked and click Next, as shown in the  
following figure.  
Tip If Windows displays a dialog box saying it cannot locate the file on the Intel PRO  
Adapter CD-ROM, insert the PCI/PXI Gigabit Ethernet Adapters CD-ROM and tell  
Windows to copy files from the Win98Me directory of the CD-ROM drive (typically  
d:\Win98Me\).  
© National Instruments Corporation  
5
PCI/PXI Gigabit Ethernet Adapters Installation Guide  
 
Tip If Windows displays a dialog box indicating it cannot locate a file on the Windows 98  
CD-ROM, try inserting the Windows 98 Installation CD-ROM and tell Windows to copy  
files from either the top directory or the win98 directory of the CD-ROM drive (typically  
d:\ or d:\win98\).  
5. Restart the computer as shown in the following figure, then connect to  
your network.  
Windows 2000/XP  
To install the drivers, complete the following steps:  
1. Shut down and power off the computer, as shown in the following  
figure.  
PCI/PXI Gigabit Ethernet Adapters Installation Guide  
6
ni.com  
 
 
2. Install the hardware and cables, then power on the computer as shown  
in the following figure.  
3. Install the Windows 2000/XP Ethernet drivers.  
Windows 2000  
Windows automatically detects the new hardware and displays a  
Found New Hardware Wizard window, as shown in the following  
figure. Insert the PCI/PXI Gigabit Ethernet Adapters CD-ROM and  
follow the directions. Choose the Recommended options when given  
a choice.  
© National Instruments Corporation  
7
PCI/PXI Gigabit Ethernet Adapters Installation Guide  
 
If Windows asks where to search for a new driver, make sure the box  
next to CD-ROM Drive is checked and click Next.  
PCI/PXI Gigabit Ethernet Adapters Installation Guide  
8
ni.com  
 
Windows XP  
Windows automatically detects the new hardware and displays a  
Found New Hardware Wizard window, as shown in the following  
figure. Insert the PCI/PXI Gigabit Ethernet Adapters CD-ROM and  
follow the directions. Choose the Recommended options when given  
a choice and click Next.  
Tip If Windows displays an Insert Disk dialog box or indicates it cannot locate a file on  
the Intel PRO Adapter CD-ROM, insert the PCI/PXI Gigabit Ethernet Adapters CD-ROM  
and tell Windows to copy files from the Win2kXP directory of the CD-ROM drive  
(typically d:\Win2kXP\).  
4. Restart the computer as shown in the following figure, then connect to  
your network (Windows 2000 only).  
© National Instruments Corporation  
9
PCI/PXI Gigabit Ethernet Adapters Installation Guide  
 
Windows NT 4.02  
To install the drivers, complete the following steps:  
1. Shut down, then power off the computer as shown in the following  
figure.  
2. Install the hardware and cables, then power on the computer as shown  
in the following figure.  
PCI/PXI Gigabit Ethernet Adapters Installation Guide  
10  
ni.com  
 
 
3. Install the Windows NT 4.0 Ethernet drivers.  
Select Start»Settings»Control Panel»Network»Adapters and click  
Add as shown in the following figure. Click Have Disk and insert the  
PCI/PXI Gigabit Ethernet Adapters CD-ROM. You may also be  
prompted for the original Windows NT CD-ROM.  
Note Service Pack 5 or later is required for Ethernet driver installation. Advanced features  
require Service Pack 6a or later.  
© National Instruments Corporation  
11  
PCI/PXI Gigabit Ethernet Adapters Installation Guide  
 
Note When installing adapters on a Windows NT system that does not have any other  
adapters installed, you must install Networking support.  
Tip If Windows displays an Insert Disk dialog box or indicates it cannot locate a file on  
the Intel PRO Adapter CD-ROM, insert the PCI/PXI Gigabit Ethernet Adapters CD-ROM  
and tell Windows to copy files from the WinNT directory of the CD-ROM drive (typically  
d:\WinNT\).  
4. Restart the computer as shown in the following figure, then connect to  
your network.  
Alternative Driver Installation Options for the PXI-8231/8232  
The installation instructions illustrated for each operating system in this  
document are appropriate for most users. However, if your PXI chassis  
does not contain a CD-ROM drive, try one of the following alternatives to  
load the Ethernet driver.  
If you have an existing Ethernet connection in your PXI chassis,  
download the Intel Ethernet driver from the National Instruments Web  
site. Access the Drivers and Downloads page at ni.com/download.  
Connect an external CD-ROM, such as a USB CD-ROM, and load the  
Ethernet driver directly from the PCI/PXI Gigabit Ethernet Drivers  
CD-ROM.  
Use another computer that has a CD-ROM to copy the Ethernet driver  
onto a 3.5 in. floppy disk:  
1. Open a DOS command window.  
2. Change to the directory on the CD-ROM that matches the OS you  
want to use with the diskette.  
3. Change to the \MAKEDISK directory.  
4. Depending on your OS, enter: MAKE2KXP, MAKENT, or MAKE98ME  
[destination (optional; A: if not specified)].  
PCI/PXI Gigabit Ethernet Adapters Installation Guide  
12  
ni.com  
 
Troubleshooting  
Windows NT Troubleshooting  
If Windows NT reports an error or you cannot connect to the network, try  
the following suggestions first. If you are still having trouble, refer to the  
additional topics in this section.  
Service Pack 5 or later is required for driver installation. Advanced  
features require Service Pack 6a or later.  
When installing adapters on a Windows NT system with no other  
adapters installed, you must install Networking support. To  
successfully install Networking and the adapter drivers, you can either:  
Copy the required Windows NT 4.0 Networking files to the hard  
drive and use the Intel CD-ROM to install the adapter driver, or  
Use the Windows NT 4.0 CD-ROM to install Networking and  
create setup disks to complete driver installation. To create setup  
disks, click Create Install Disk in the Autorun screen.  
Make sure you are using the drivers provided on the PCI/PXI Gigabit  
Ethernet Adapters CD-ROM.  
Make sure the drivers are loaded and the protocols are bound. Check  
the settings in the Network/Bindings dialog box in the Control Panel.  
Check the Windows NT Event Viewer for error messages.  
Make sure Plug and Play OS is set to NO in your computer’s BIOS.  
Test the adapter with the PROSet 2 advanced configuration utility that  
was installed on your system when you installed the drivers. To start  
PROSet, double-click the PROSet 2 icon in the Windows Control  
Panel. To run diagnostics, select the adapter and click the Diagnostics  
tab, then click Run Tests.  
If you do not see the ProSet 2 icon, refer to the Additional  
Troubleshooting Tools section.  
Testing the Adapter  
Test the adapter by running diagnostics. To test the Ethernet functionality,  
run PROSet 2 by double-clicking the PROSet 2 icon in the Control Panel.  
Select the adapter and click the Diagnostics tab, then click Run Tests.  
If your board has GPIB functionality, run the NI-488.2 Getting Started  
Wizard to verify your hardware and software installation.  
© National Instruments Corporation  
13  
PCI/PXI Gigabit Ethernet Adapters Installation Guide  
 
WOL558.VXD Missing or Not Found (Windows 98 Only)  
This error can occur in Windows 98 if an .inf file already installed on the  
system interferes with the driver installation. Complete the following steps  
to manually install the Ethernet adapter:  
1. Open Windows Explorer.  
2. Select Views»Folder Options.  
3. Select the View tab.  
4. Select Show all files and click OK.  
5. Delete net557.inf and net557.pnf in the Windows/inf folder.  
6. Double-click the System icon from the Control Panel.  
7. Select the Device Manager tab and double-click Network Adapters.  
8. Select the Intel PRO/1000 MT Desktop Adapter and click Remove.  
9. Restart your computer.  
10. Follow the instructions given previously in the Windows Me/98 section  
to install the Windows 98 drivers.  
Adapter Cannot Connect to the Network  
1. Make sure the cable is installed properly.  
The network cable must be installed properly at both the adapter and  
the hub. The maximum distance for the cable is 100 m. If the cable is  
connected properly and within the allowed distance, try another cable.  
2. Check the LEDs on the adapter.  
The adapter has two LEDs located on the RJ-45 connector.  
The following table lists the function of each LED.  
LED Color  
Green  
Function  
Indication  
Meaning  
Action/Link  
On  
The adapter is receiving power. The cable  
connection is good.  
Off  
The adapter is not sending or receiving  
network data. The adapter is not receiving  
power. The cable connection is bad or you  
have a driver problem.  
Flashing  
The adapter is sending and receiving  
network data.  
Yellow/Green  
Speed  
Yellow  
Green  
Off  
The adapter is operating at 1,000 Mb/s.  
The adapter is operating at 100 Mb/s.  
The adapter is operating at 10 Mb/s.  
PCI/PXI Gigabit Ethernet Adapters Installation Guide  
14  
ni.com  
 
3. Make sure you are using the correct drivers.  
Verify that you are using the drivers that came with the adapter.  
Computer Hangs when Drivers Are Loaded  
Change the PCI BIOS interrupt settings. Refer to the PCI/PXI Installation  
Tips section for more information.  
Diagnostics Pass, but Connection Fails or Errors Occur  
Check the responding link partner.  
Make sure the cable is securely attached, is the proper type, and does  
not exceed the recommended lengths.  
Try another cable.  
Make sure the duplex mode and speed setting on the adapter matches  
the setting on the switch.  
Link LED Does Not Light  
Make sure the network drivers are loaded.  
Check the cable connection.  
ACT LED Does Not Light  
Make sure the correct network drivers are loaded.  
The network may be idle.  
Adapter Has Stopped Working  
Run the diagnostics. Refer to the Additional Troubleshooting Tools  
section.  
Try reseating the adapter in the PCI/PXI slot or try a different slot.  
The network drivers may be corrupt or missing. Try removing and  
reinstalling the drivers.  
Try rebooting the computer.  
Try another cable.  
Try a different adapter.  
Link LED Is Not Lit when Computer Is Shut Down and Power Is Connected  
Make sure the network cable is attached.  
© National Instruments Corporation  
15  
PCI/PXI Gigabit Ethernet Adapters Installation Guide  
 
PCI/PXI Installation Tips  
PCI/PXI computers are designed to automatically configure add-in boards  
each time the computer starts. The PCI/PXI computer sets the I/O address  
and IRQ level for the peripheral boards when the computer starts. The  
network drivers cannot change these values. If you experience problems  
when the computer starts, you may have to follow additional steps.  
On some computers, manual configuration is possible through the  
computer’s BIOS setup utility. Refer to the documentation that came with  
your computer. You may need to verify or change some BIOS settings.  
The following common solutions may correct your problem:  
Make sure you have installed the adapter in a bus master-enabled slot.  
On some computers, not all slots are bus master enabled by default.  
Check your BIOS settings. Enable PCI/PXI bus mastering, if your  
BIOS has such an option.  
Reserve interrupts (IRQ) and/or memory addresses for ISA adapters.  
This prevents PCI/PXI boards from using the same settings ISA boards  
are using. Try changing some of the interrupts that are reserved for  
ISA, but not being used, to reserved for PCI/PXI.  
Update your BIOS. Sometimes updating the BIOS will correct some  
configuration problems.  
Configure the PCI/PXI slot for level-triggered interrupts instead of  
edge-triggered interrupts in BIOS.  
Additional Troubleshooting Tools  
The PCI/PXI Gigabit Ethernet Adapters CD-ROM contains an Intel utility  
for troubleshooting the gigabit Ethernet adapter.  
To install the tool, complete the following steps:  
1. Navigate to the appropriate directory for your operating system on the  
PCI/PXI Gigabit Ethernet Adapters CD-ROM.  
2. Run the setup.exe program.  
3. Start the tool by double-clicking the Ethernet Adapter icon in the  
system tray.  
PCI/PXI Gigabit Ethernet Adapters Installation Guide  
16  
ni.com  
 
   
Ethernet Adapter Specifications  
Dimensions  
PXI-8232/8231................................ 16.0 by 9.9 cm  
(6.3 by 3.9 in.)  
Power requirements  
PXI-8232......................................... 3.0 W at +3.3 VDC typical  
PXI-8231......................................... 2.6 W at +3.3 VDC typical  
Operating environment  
Ambient temperature ...................... 0 to 55 °C  
Relative humidity............................ 10 to 90%, noncondensing  
Storage environment  
Temperature.................................... –20 to 70 °C  
Relative humidity............................ 5 to 90%, noncondensing  
Compliance and Certification  
FCC Class A Certified  
CE  
I/O connectors  
GPIB (PCI/PXI-8232 only) ............ IEEE 488 Standard 24-pin  
Ethernet........................................... RJ-45  
LEDs  
Green............................................... Activity/Link  
Yellow/Green.................................. Speed  
Ethernet data rate mode.......................... 10 Mb/s, 100 Mb/s, or 1,000 Mb/s  
© National Instruments Corporation  
17  
PCI/PXI Gigabit Ethernet Adapters Installation Guide  
 

Miele Washer W 211 User Manual
Miller Electric Air Compressor AC Generator Air Compressor User Manual
MTD Chipper 245 650 000 User Manual
Multiquip Automobile Parts DSGPULW User Manual
National Instruments Computer Accessories 370757C 01 User Manual
Oregon Scientific Radar Detector BAR608HGA User Manual
Panasonic Air Conditioner CS MKE12NKU User Manual
Panasonic Camera Lens AW LZ10MD6 for AW E300 Series User Manual
Panasonic Car Stereo System CQ C1105W User Manual
Panasonic Car Video System CY VM7203W User Manual