Brick, Concrete and Stone wall(Fig 2c):
Using the wall mount as template to mark 6 holes location on the wall. There holes are
located at the top row of the slots and three more are located at the bottom row. The
outer holes must be fall to the left and right of the two holes in the middle of the
mount. Please make sure these holes are level and at least 6” between any two lines.
Pre-drill these holes with a 10mm drill bit to at least 80mm deep hole. Insert Wall
anchors(P) into each of these holes. Attach the wall mount to the wall using 6 Long
bolts(O) and washers(Q).
1
Fixed Flat Panel TV Bracket
Multifunctional double deck wall mount
INSTALLATION GUIDE
Q
O
Item No.:PSW112
Fig 2c
Fig 2b
Step 3: Hanging display
Firstly lift the bracket mounted display over the wall mount. And then hook the
brackets over the top of the wall mount. Rotate the display let the bottom of the
brackets hook over the bottom of wall mount, as shown in Fig.3a. Then put safe
bolts into the bottom of the brackets and lock it, as shown in Fig.3b.
Warning: Some TV require two people to lift, as we are not responsible for any
personal injury or product damage due to mishandling.
2,3
Easy installing: Just hang up the display
Safety: locking by spining bolt on the bottom
Max load capacity:75kg(165lbs）
TV size range: 36"~55"
4
1
Fig 3a
Fig 3b
,
-8-
IMPORTANT: If don’t understand about right install ways, please
consult to normal installing specialist.
3. For display with protruding HDTV tune or deeply
curved backs(Fig b), two 9/16” spacers(R) or two
½” spacers(S) should be used. Stack two spacers
and then install them between display and the
bracket. As shown in Fig 1c.
WARNING
Fig b
M5 Fig bit
We are not responsible for any personal injury or product damage due to mishandling,
incorrect mounting, incorrect assembly or incorrect use of this product.
M4 Fig bit
Note: The supplied wall mounting hardware is not for use on steel stud walls or cold
cinder block walls. If you are uncertain about the nature of your wall, please consult a
qualified contractor. If the hardware you required is not included please contact your
local hardware store or the nearest Circuit City Stores.
R
I
R
Caution:
This Product LCD /Plasma Wall Mount Bracket is intended for use only
3
N
N
2
J
with the maximum weights indicated .See apparatus instructions .Use with products
heavier than the maximum weights indicated may result in instability causing possible
injury .
Step 1: Attach bracket to TV
Check your TV manual to confirm the diameter of bolt to be used or choose an
appropriate bolt according to size, height and position of the holes on your TV. See
pages 4-6 of these instructions for examples.
For correct installing, make sure that hook of every bracket must facing down. Use
selected bolt, spacers and washer for installing bracket at the back of display.
Adjust two brackets to equal heights and level. Once aligned, tightly secure the
bolts.
S
R
IMPORTANTT: Don't force the bolt into the hole, which will cause a damage of
N
K
equipments and injure of person. Don't use electric drill to fasten any bolts.
N
L
2
3
M6 Fig bit
M8 Fig bit
Fig 1c
-3-
-6-
Following examples shows how to use bolts, spacers and square washers.
2. Some displays have curved backs with
recessed mounting lands(Fig.a). It will
require the use of spacer. For this display,
install a 9/16” spacer(R) or ½”spacer(S)
between display and the bracket. As
shown in Fig 1b.
1.Some displays have vertical backs. No spacer is required. Install the bracket directly
to the back of display by using bolts and square washers provided. As shown in Fig.1a.
Fig a
M4 Fig bit
M5 Fig bit
M4 Fig bit
M5 Fig bit
R
N
R
A
E
3
2
B
N
2
N
F
3
N
S
2
N
R
3
H
N
G
2
D
N
3
N
C,M
M6,1/4＂-20 5/8＂Fig bit
M8 Fig bit
M6 Fig bit
M8 Fig bit
Fig 1b
Fig 1a
-5-
-4-
|