I N S T A L L A T I O N
WM5000 Series
Wall Mount Kit
For Endura® Modules
C1616M-A (1/08)
Description
With a WM5000 Series wall mount kit, you can attach up to four Endura modules to the wall in any orientation. The WM5001-4U is a base kit
consisting of a wall bracket and a module sleeve with a cover plate.
WARNING: Do not attach more than four module sleeves with modules. The excessive weight can cause the equipment to fall from the
wall.
Expansion kits are available if you want to add more module sleeves to a wall bracket. The WM5001-4UEXP expansion kit consists of an
additional module sleeve.
The wall bracket and module sleeve interlock are secured with two 4-40 screws, which are located on the module sleeve. Module sleeves attach
to one another in the same way. The wall bracket can support up to four module sleeves.
Rubber feet are attached to the wall bracket giving you the option of desktop placement for stacking the modules.
MODELS
WM5001-4U
WM5001-4UEXP
Wall mount base kit for a single module
Wall mount expansion kit for an additional module
C1616M-A (1/08)
3
Installation
PACKAGE CONTENTS
WM5001-4U
1
1
Wall bracket
Module sleeve with cover plate
WM5001-4UEXP
Module sleeve
1
MOUNTING A WALL BRACKET
You can mount a wall bracket onto a wall so that the modules can be inserted into the sleeves from the right, left, top, or bottom.
NOTE: The back of the wall bracket has four rubber feet for placing the mount on a desk. The feet do not need to be removed if the mount is
installed on a wall.
1. Position the bracket on the wall in your desired orientation.
2. Drill four holes into the wall.
3. Secure the wall bracket to the wall using four 8-32 screws with washers (not supplied).
Figure 1. Wall Bracket Mounting
4
C1616M-A (1/08)
ATTACHING A MODULE SLEEVE
Your base kit comes with a single module sleeve. The optional expansion kits allow you to add more module sleeves.
WARNING: Do not attach more than four module sleeves with modules. The excessive weight can cause the equipment to fall from the
wall.
1. Attach the module sleeve to the wall bracket by inserting the four tabs on the module sleeve into the four openings on the wall bracket.
2. Remove the two 4-40 screws from location A and screw them into location B.
You must remove the cover plate on the module sleeve before adding additional module sleeves.
LOCATION B
LOCATION A
LOCATION B
Figure 2. Module Sleeve Attachment
REMOVING A COVER PLATE
To add additional module sleeves, you must remove the cover plate from the supplied module sleeve. Refer to Figure 3.
Figure 3. Cover Plate Removal
C1616M-A (1/08)
5
INSTALLING A MODULE
1. Insert a module into the module sleeve.
2. Tighten the thumbscrew on the bottom of the module sleeve to secure the module.
NOTE: Do not attach a WM5001-4UEXP when either a NET5301T-I or a NET5301T-C is in the WM5001-4U.
Figure 4. Module Installation
Specifications
MECHANICAL
Number of Slots
Module Orientation
Rack Units
1
Variable
4
Construction
Aluminum
Black
Mounting
GENERAL
Dimensions*
Mounting
2.19" D x 7.88" W x 6.69" H (5.56 x 20.02 x 16.99cm)
Wall or desktop
Unit Weight
WM5001-4U
WM5001-4UEXP
1.46 lb (0.66 kg)
0.42 lb (0.19 kg)
6
C1616M-A (1/08)
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in
material or workmanship for a period of one year after the date of shipment.
Pelco assumes no risk and shall be subject to no liability for damages or loss
resulting from the specific use or application made of the Products. Pelco’s liability
for any claim, whether based on breach of contract, negligence, infringement of
any rights of any party or product liability, relating to the Products shall not exceed
the price paid by the Dealer to Pelco for such Products. In no event will Pelco be
liable for any special, incidental, or consequential damages (including loss of use,
loss of profit, and claims of third parties) however caused, whether by the
negligence of Pelco or otherwise.
Exceptions to this warranty are as noted below:
•
Five years on fiber optic products and TW3000 Series unshielded twisted pair
(UTP) transmission products.
•
•
•
Three years on Spectra® IV products.
Three years on Genex® Series products (multiplexers, server, and keyboard).
The above warranty provides the Dealer with specific legal rights. The Dealer may
also have additional rights, which are subject to variation from state to state.
Three years on DX Series digital video recorders, DVR5100 Series digital video
®
recorders, DigitalSENTRY Series hardware products, DVX Series digital video
recorders, NVR300 Series network video recorders, and Endura® Series
distributed network-based video products.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the
following information:
•
Three years on Camclosure® and Pelco-branded fixed camera models, except
the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and
MC3651H-2X camera models, which have a five-year warranty.
1. Model and serial number
2. Date of shipment, P.O. number, sales order number, or Pelco invoice number
3. Details of the defect or problem
•
•
•
Three years on PMCL200/300/400 Series LCD monitors.
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8
Series fixed dome products.
Two years on Spectra III™, Spectra Mini, Esprit®, ExSite®, and PS20 scanners,
including when used in continuous motion applications.
If there is a dispute regarding the warranty of a product that does not fall under
the warranty conditions stated above, please include a written explanation with
the product when returned.
•
•
•
Method of return shipment shall be the same or equal to the method by which the
item was received by Pelco.
Two years on Esprit and WW5700 Series window wiper (excluding wiper
blades).
Two years (except lamp and color wheel) on Digital Light Processing (DLP®)
displays. The lamp and color wheel will be covered for a period of 90 days. The
air filter is not covered under warranty.
RETURNS
To expedite parts returned for repair or credit, please call Pelco at (800) 289-9100
or (559) 292-1981 to obtain an authorization number (CA number if returned for
credit, and RA number if returned for repair) and designated return location.
•
•
Two years on Intelli-M® eIDC controllers.
One year (except video heads) on video cassette recorders (VCRs). Video heads
will be covered for a period of six months.
All merchandise returned for credit may be subject to a 20 percent restocking and
refurbishing charge.
•
Six months on all pan and tilts, scanners, or preset lenses used in continuous
motion applications (preset scan, tour, and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of
Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid
to a Pelco designated location. Repairs made necessary by reason of misuse,
alteration, normal wear, or accident are not covered under this warranty.
Goods returned for repair or credit should be clearly identified with the assigned
CA or RA number and freight should be prepaid.
REVISION HISTORY
Manual #
C1616M
C1616M-A
Date
4/05
1/08
Comments
Original version.
Added note to Installing a Module section.
Pelco, the Pelco logo, Camclosure, DigitalSENTRY, Endura, Esprit, ExSite, Genex, Intelli-M, Legacy, and Spectra are registered trademarks of Pelco, Inc.
Spectra III is a trademark of Pelco, Inc.
© Copyright 2008, Pelco, Inc. All rights reserved.
DLP is a registered trademark of Texas Instruments Incorporated.
Worldwide Headquarters
3500 Pelco Way
Clovis, California 93612 USA
USA & Canada
Tel: 800/289-9100
Fax: 800/289-9150
International
Tel: 1-559/292-1981
Fax: 1-559/348-1120
ISO9001
Australia Canada Finland France Germany Italy Macau The Netherlands Russia Singapore
|
|
|
|
|
|
|
|
|
South Africa Spain Sweden United Arab Emirates United Kingdom United States
|
|
|
|
|
|