= Vertical bar in the right margin indicates change or addition.
SWM-PA Series
Pole Adapter for the
Spectra® Compact
Wall Mount
Installation/Operation Manual
C294M (11/98)
1. Installation and servicing should only be done by qualified service personnel
and conform to all local codes.
1.0 WARNINGS
2. Installation shall be done in accordance with all local and national electrical
and mechanical codes utilizing only approved materials.
Please thoroughly familiarize yourself with the information in this
manual prior to installation and operation.
The SWM-PA Series Pole Adapter is designed to adapt Pelco’s SWM Series Spec-
tra® Compact Wall Mount to a pole. It can be used for either indoor or outdoor
applications. The adapter is supplied with two stainless steel straps and two stain-
less steel screws. The adapter is attached to a pole with the two straps, and a
mounting cleat (supplied with the wall mount) is installed on the adapter with the
two stainless steel screws. Once the mounting cleat is firmly in position on the
adapter, the SWM wall mount is then attached and held in place by a set screw.
The adapter and mounting cleat both have a feedthrough opening for electrical
cables, not a conduit fitting.
2.0 DESCRIPTION
The adapter is constructed of aluminum and has either a light gray or black polyes-
ter powder coat finish.
SWM-PA-GY
SWM-PA-BK
Pole adapter for use with the SWM Series Spectra® Compact
Wall Mount. Gray finish.
2.1 MODELS
Same as SWM-GY, except black finish.
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150
International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120
3.2 SWM SERIES
SPECTRA® COMPACT
WALL MOUNT
To install the SWM Series wall mount (not supplied) to the pole adapter, perform
the following steps (see Figure 1):
1. Feed the electrical cables through the hole in the mounting cleat, and install
the cleat securely onto the adapter with two 1/4-20 socket head screws (sup-
plied). Position the cleat so the elongated mounting hole is below the cable
entry hole.Adjust the vertical alignment of the cleat before tightening the screws.
NOTE: Make sure no moisture
has condensed inside the mount
before installation.
2. Feed the electrical cables through the mount, hook the mount onto the top of
the mounting cleat, and position the mount flush against the pole adapter.
Back out, if necessary, and tighten the set screw in the bottom of the mount
only until the mount is snug against the surface of the adapter. Do not over-
tighten.
NOTE: The mounting cleat has
an arrow embossed in it, for orien-
tation purposes, and must point up-
ward.
3. Attach the pendant dome back box to the mount:
a. Feed the electrical cables from the mount into the dome back box.
b. Apply anti-seize compound to the dome back box pipe threads.
c. Screw the dome back box into the threads in the mount.
d. Complete the installation following the instructions in the dome manual.
NOTE: Anti-seize compound is
supplied with the SWM Series wall
mount.
4.0 SPECIFICATIONS
MECHANICAL
Construction:
Aluminum
Finish
SWM-PA-GY:
SWM-PA-BK:
Gray polyester powder coat
Black polyester powder coat
Mount Method:
Adapter is attached to a pole with two stainless steel
straps (supplied). Two stainless steel screws (supplied)
areusedtoattachthewallmountcleat(notsupplied)tothe
adapter.Thelowerholeinthemountingcleatiselongated,
which allows for vertical alignment adjustment.
Cable Entry:
One cable feedthrough hole in the adapter and the mount-
ing cleat
Maximum Load:
GENERAL
Environment:
Dimensions:
Weight:
10 lb (4.5 kg)
Indoor/outdoor
5.00" H x 3.65" W x 1.50" D (12.70 x 9.27 x 3.81 cm)
Unit
0.7 lb (0.32 kg)
Shipping
2.0 lb (0.91 kg)
(Design and product specifications subject to change without notice.)
Pelco Manual C294M (11/98)
3
5.0 WARRANTY AND
RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or workman-
ship for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:
• Five years on FT/FR8000 Series fiber optic products.
• Three years on Genex® Series products (multiplexers, server, and keyboard).
• Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X,
CC3751H-2, CC3651H-2X, MC3651H-2, and CC3651H-2X camera models, which have a five-year
warranty.
• Two years on standard motorized or fixed focal length lenses.
• Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series
fixed dome products.
• Two years on Spectra®, Esprit®, ExSite™, and PS20 Scanners, including when used in continuous
motion applications.
• Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).
• Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and
Endura™ Series distributed network-based video products.months on DX Series digital video
corders, NVR300 Series network video recorders, Endura™ Series distributed network-based video
products, and TW3000 Series twisted pair transmission products.
re-
• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a
period of six months.
• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications
(that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All
goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made
necessary by reason of misuse, alteration, normal wear, or accident are not covered under this
warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the spe-
cific use or application made of the Products. Pelco’s liability for any claim, whether based on breach of
contract, negligence, infringement of any rights of any party or product liability, relating to the Products
shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable
for any special, incidental or consequential damages (including loss of use, loss of profit and claims of
third parties) however caused, whether by the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional
rights, which are subject to variation from state to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to
obtain a Repair Authorization number (RA), and provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the warranty condi-
tions stated above, please include a written explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received by
Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800)
289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and
RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and
freight should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to
return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
® Pelco, the Pelco logo, Spectra, Esprit, Genex, Legacy, and Camclosure are registered trademarks of Pelco.
™ Endura and ExSite are trademarks of Pelco.
© Copyright 1998, Pelco. All rights reserved.
4
Pelco Manual C294M (11/98)
|