C491M-D (3/99)
HS4100BH
High-Security Camera Enclosure
®
IMPORTANT SAFEGUARDS AND WARNINGS
Prior to installation and use of this product, the following WARNINGS should be observed.
300 W. Pontiac Way,
Clovis, CA 93612-5699
USA
1. Installation and servicing should only be done by qualified service personnel and conform
to all local codes.
In North America & Canada:
Tel (800) 289-9100
FAX (800) 289-9150
DataFAX (800) 289-9108
2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X ,6 or 6P enclo-
sure, it is designed for indoor use only and it must not be installed where exposed to rain
and moisture.
International Customers:
Tel (1-559) 292-1981
FAX (1-559) 348-1120
DataFAX (1-559) 292-0435
3. Only use replacement parts recommended by Pelco.
4. The installation method and materials should be capable to supporting four times the
weight of the enclosure, pan/tilt, camera and lens combination.
Pelco Online
5. The camera and lens combination shall not exceed 20 pounds (9.06 kg).
The product and/or manual may bear the following marks:
This symbol indicates that danger-
ous voltage constituting a risk of
electric shock is present within this
U
®
L
C A U T I O N :
unit.
RISK OF ELECTRIC SHOCK.
This symbol indicates that there are
important operating and mainte-
nance instructions in the literature
accompanying this unit.
DO NOT OPEN.
Please thoroughly familiarize yourself with the information in this manual prior to installation
and operation.
DESCRIPTION
The HS4100BH is a high-security camera enclosure designed to be mounted in indoor walls in
applications requiring maximum protection from vandalism, such as prisons and detention
cells.
There is no exposed mounting hardware holding the enclosure to its mounting surface be-
cause the HS4100BH replaces a half-size concrete block during construction of the wall. The
HS4100BH is made of heavy-gauge steel and is equipped with a window of 1/2-inch (1.27 cm)
thick, impact-resistant Lexan®.
The HS4100BH accepts most CCD cameras with fixed focal length lenses and some motor-
ized zoom lenses. Access to the inside is through the front or rear with a specially designed
tool, so the enclosure cannot be opened by unauthorized people. In addition, a factory-in-
stalled tamper switch is mounted on the secured access cover.
INSTALLATION
The following parts are supplied:
1
1
Enclosure
Tampruf #10 socket, 1/4-inch drive
The HS4100BH is designed to be installed in a concrete block wall during construction. The
enclosure’s dimensions allow it to replace a half-size block.
Before installing the HS4100BH enclosure in a wall, make certain the wall detail and construc-
tion can support the full weight of the enclosure plus the camera and lens. The HS4100BH
must not be considered a structural component in a wall. Make sure during construction that
the access panels are not obstructed by mortar.
GENERAL
Construction:
Seam-welded 10-gauge (0.134 in. or 0.34 cm) steel
Gray polyester powder coat
Finish:
Dimensions:
Environment:
Weight:
See Figure 1
Indoor; 32° to 120°F (0° to 49°C)
Unit
Shipping
23 lb (10.35 kg)
27 lb (12.23 kg)
Rating:
NEMA 1
IP 20
(Design and product specifications subject to change without notice.)
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS;
ALL OTHERS ARE INCHES
Figure 1. HS4100BH Dimension Drawing
WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defec-
tive in material or workmanship for a period of one year after the date of
shipment. Exceptions to this warranty are as noted below:
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-
9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and
provide the following information:
•
•
•
Three years on Genex™ Series (multiplexers, server, and keyboard).
Two years on all standard motorized and fixed focal length lenses.
Two years on Esprit™, Legacy®, Intercept®, PV1000 Series, CM6700/
CM8500/CM9500/CM9750/CM9760 Matrix, Spectra®, DF5 Series and DF8
Fixed Dome products.
Two years on WW5700 series window wiper (excluding wiper blades).
Two years on cameras.
Six months on all pan and tilts, scanners or preset lenses used in continuous
motion applications (that is, preset scan, tour and auto scan modes).
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall
under the warranty conditions stated above, please include a written expla-
nation with the product when returned.
•
•
•
Ship freight prepaid to:
Pelco
300 West Pontiac Way
Clovis, CA 93612-5699
Pelco will warrant all replacement parts and repairs for 90 days from the date
of Pelco shipment. All goods requiring warranty repair shall be sent freight
prepaid to Pelco, Clovis, California. Repairs made necessary by reason of
misuse, alteration, normal wear, or accident are not covered under this war-
ranty.
Method of return shipment shall be the same or equal to the method by which
the item was received by Pelco.
RETURNS
Pelco assumes no risk and shall be subject to no liability for damages or loss
resulting from the specific use or application made of the Products. Pelco’s
liability for any claim, whether based on breach of contract, negligence, in-
fringement of any rights of any party or product liability, relating to the Prod-
ucts shall not exceed the price paid by the Dealer to Pelco for such Products.
In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) how-
ever caused, whether by the negligence of Pelco or otherwise.
In order to expedite parts returned to the factory for repair or credit, please
call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authoriza-
tion number (CA number if returned for credit, and RA number if returned for
repair). Goods returned for repair or credit should be clearly identified with
the assigned CA/RA number and freight should be prepaid. All merchandise
returned for credit may be subject to a 20% restocking and refurbishing charge.
Ship freight prepaid to:
Pelco
The above warranty provides the Dealer with specific legal rights. The Dealer may
also have additional rights, which are subject to variation from state to state.
300 West Pontiac Way
Clovis, CA 93612-5699
REVISION HISTORY
Manual # Date
Comments
C491M
5/90
9/95
11/95
1/96
11/96
2/99
Original manual.
C491M-A
C491M-B
C491M-c
Rev. A. Revised to include wiring instructions for tamper switch and metric equivalents for specifications.
Rev. B. Revised to include updated tamper switch/bracket part numbers and exploded view diagram.
Revised to include tamper switch installation, specification description and new part numbers per ECO 95-397.
Revised Section 6.2 Mechanical Parts List for HS4100BH Enclosure. The quantity of item no. 8 is to be 6 instead of 8.
Removed material related to HS4100BF. Added certifications information. Moved an exploded assembly drawing and parts list
to a new HS4100BH service manual. Reformatted the manual.
C1491M-D
®Pelco and the Pelco logo are registered trademarks of Pelco.
© Copyright 1999, Pelco. All rights reserved.
|