®
HS4000
High-Security Enclosure
Installation/Operation Manual
C497M-D (1/96)
(800) 289-9100 or (1-559) 292-1981 • FAX (800) 289-9150 or (1-559) 292-3827
International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120
INSTALLATION/OPERATION MANUAL
HS4000 HIGH-SECURITY ENCLOSURE
1.0 WARNINGS
Priortoinstallationanduseofthisproduct,thefollowing
WARNINGS should be observed.
4. After replacement/repair of this unit’s electrical
components, conduct a resistance measurement
betweenlineandexposedpartstoverifytheexposed
parts have not been connected to line circuitry.
1. Installation and servicing should only be done by
Qualified Service Personnel and conform to all
Local codes.
5. The installation method and materials should be
capable of supporting four (4) times the weight of
theenclosure,pan/tilt,cameraandlenscombination.
2. Unless the unit is specifically marked as a NEMA
Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is
designed for indoor use only and it must not be
installed where exposed to rain and moisture.
3. Only use replacement parts recommended by
PELCO.
The product may bear the following
marks:
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit.
This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.
CAUTION:
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
CAUTION:
TOREDUCETHERISKOFELECTRICAL
SHOCK, DO NOT REMOVE COVER. NO
USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Please thoroughly familiarize yourself with the information in this manual
prior to installation and operation.
Pelco Manual C497M-D (1/96)
1
2.0 SCOPE
This enclosure has a removable rear cap for easy ac-
cess to the slide-out platform on which the camera is
mounted. The removable front cap allows manual lens
adjustments to be made without removing the camera.
Access to the interior can only be gained with a spe-
cially designed tool, eliminating the possibility of the
enclosure being opened by unauthorized personnel.
The information contained within this manual covers
the HS4000 High Security Camera Enclosure.
2.1 DESCRIPTION
The HS4000 is a high-security camera enclosure de-
signed for use with 2/3-inch cameras and will accom-
modate fixed focal length lenses or motorized zoom
lenses with or without auto-iris operation.
A factory-installed tamper switch provides additional
security.
The HS4000 has been engineered for indoor use as a
stand-alone enclosure in prisons, detention cells, or
other applications requiring maximum protection from
vandalism.
Figure 1. HS4000 Dimension Drawing
2
Pelco Manual C497M-D (1/96)
3.0 INSTALLATION
3.1 CAMERA/LENS INSTALLATION
The following hardware is supplied with the enclosure
and can be used to mount the enclosure or the camera/
lens:
1. Remove the four (4) “tampruf” screws from the
rear cap with the tool provided.
2. Remove the rear cap from the enclosure. Loosen
the bolt on the camera sled assembly and remove
it from the rail.
Quantity
Item
2
4
4
2
1/4-20 x .500 hex head screws
1/4 flat washers
1/4 split washers
3. Place the camera/lens on the sled assembly.
1/4-20 “tampruf” screws
NOTE: Position the camera/lens at the
forward-most point on the sled, while al-
lowing clearance between the lens and en-
closure window when the lens is adjusted
to its maximum physical length.
4. Secure the camera/lens to the sled with the 1/4-20
hex head screws provided.
5. Pull the video and power cables through the knock-
outs and attach to the camera.
6. Adjust camera focus and iris if necessary.
7. Replace the sled onto the rail and slide the assem-
bly into the enclosure; replace the bolt and secure.
8. Replace the rear cap and the four (4) “tampruf”
screws.
9. Attach the enclosure to the appropriate mount or
pan/tilt using the instructions provided.
NOTE: If the lens needs to be adjusted fur-
ther after installation has been completed, it is
easier to remove the front cap to make final lens
adjustments.
Pelco Manual C497M-D (1/96)
3
4.0 TAMPER SWITCH INSTALLATION
6.0 SPECIFICATIONS
MECHANICAL
The HS4000 High-Security enclosures come standard
from the factory with a tamper switch(es) mounted on
the secured access door. Refer to Section 4.1 for wir-
ing.
Camera
Mounting:
Viewing
Multiple holes on camera sled
Window:
1/2" (1.27 cm) thick impact and abra-
sion resistant Lexan
Should it become necessary to install a replacement
switch, reference Figure 2 and perform the following
steps:
Camera Size:
Accommodates camera/lens combi-
nations up to:
6.00" W x 4.75" H x 15.00" L
(15.24 cm x 12.07 cm x 38.10 cm)
Tamper Switch: Plunger type door switch with “pull
to cheat” feature. N.O/N.C. contacts
1. Open the enclosure by removing the end plate from
the desired “alarmed” opening.
clearly marked on body of switch.
DM electrical rating: 10A, 125V.
2. Install the bracket so that the mounting studs go
through the slots in the bracket.
Security:
Tamper-resistant screws N.O./N.C.
switch contact on secure cover
NOTE: The slot in the bracket allows the switch
to be used against either the 1/2" (1.27 cm) thick
lexan window or the .134" (0.34 cm) thick metal
plate.
ELECTRICAL
Cable Entry:
Two (2) cable knockout holes on rear
plate
Tamper Switch: 1/4" (.63 cm) quick connect. N.O./
N.C. clearly marked on switch body.
3. If the switch is to be used against the metal plate,
slide the bracket so that the studs are at the end of
the slot that is furthest from the switch plunger.
10A, maximum switching current
125V, maximum switching voltage.
4. If the switch is to be used against the Lexan win-
dow, slide the bracket so that the studs are at the
end of the slot nearest the switch plunger.
GENERAL
Construction:
Seam welded 10 gauge .134" (0.34
cm) steel
Finish:
Dimensions:
Weight:
Poly vinyl powder coat
See Figure 1
22 lbs (9.9 kg)
5. When reinstalling the front/rear plate, position the
plate flush with the end of the enclosure body.
4.1 WIRING THE SWITCH
(Product specifications subject to change
without notice.)
The tamper switch comes with both a “Normally Open”
contact and a “Normally Closed” contact.
•
•
For a “Normally Open” circuit, use the “open” and
“common” terminals.
For a “Normally Closed” circuit, use the “closed”
and “common” terminals.
5.0 CARE AND MAINTENANCE
Regularly scheduled maintenance will help prolong the
appearance of the equipment.
Clean the window regularly with a soft cloth and mild
nonabrasive detergent in water to help maintain picture
clarity.
Figure 2. HS4000 Series Tamper Switch Installation
4
Pelco Manual C497M-D (1/96)
7.0 EXPLODED ASSEMBLY DIAGRAM
Figure 3. HS4000 Exploded Assembly Diagram
7.1 MECHANICAL PARTS LIST
Item
Quantity
Description
Part Number
1
2
3
4
5
6
7
8
9
1
1
2
1
1
2
2
10
1
Lexan window
Body assembly
Front/rear plate
Sled
Knockouts plate
Tamper switch bracket
Tamper switch
Screws, “tampruf” #10, SS, 1/4-20 x 1/2" round
Socket, “tampruf” #10
AH80001001
HS40001100WA
HS40004003COMP
EH40144001COMP
HS40004015COMP
HS30004113COMP
SWI1DM401
ZH1/4-20X.50SRT
ZTSOCKET10
A
B
C
D
E
F
4
16
1
4
4
1/4-20 Nut-lock
1/4" Flat washer
1/4-20 x 1.25" Screw
1/4" Split lock washer
1/4-20 Hex nut
ZH1/420NUTCHN
ZH260X562X65C
ZH1/420X1.25CS
ZH1/4LWSSL
ZH1/4-20 NUTCH
ZH6LWSIS
4
4
#6 Lock washer
6-32 Hex nut
G
ZH6-32NUTSH
Pelco Manual C497M-D (1/96)
5
8.0 WARRANTY AND RETURN
INFORMATION
WARRANTY
RETURNS
Pelco will repair or replace, without charge, any merchandise proved
defectiveinmaterialorworkmanshipforaperiodofoneyearafterthedate
of shipment.
In order to expedite parts returned to the factory for repair or credit, please
call the factory at (800) 289-9100 or (559) 292-1981 to obtain an
authorization number (CA number if returned for credit, and RA number
if returned for repair).
Exceptions to this warranty are as noted below:
All merchandise returned for credit may be subject to a 20% restocking
and refurbishing charge.
•
•
Five years on FT/FR8000 Series fiber optic products.
Three years on Genex® Series products (multiplexers, server, and
keyboard).
Three years on Camclosure® and fixed camera models, except the
CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,
and MC3651H-2X camera models, which have a five-year warranty.
Goods returned for repair or credit should be clearly identified with the
assigned CA or RA number and freight should be prepaid. Ship to the
appropriate address below.
•
If you are located within the continental U.S., Alaska, Hawaii or Puerto
Rico, send goods to:
•
•
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and
DF5/DF8 Series fixed dome products.
Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, includ-
ing when used in continuous motion applications.
Two years on Esprit® and WW5700 Series window wiper (excluding
wiper blades).
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
•
•
•
If you are located outside the continental U.S., Alaska, Hawaii or Puerto
Rico and are instructed to return goods to the USA, you may do one of the
following:
Eighteen months on DX Series digital video recorders, NVR300
Series network video recorders, and Endura™ Series distributed
network-based video products.
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
•
•
One year (except video heads) on video cassette recorders (VCRs).
Video heads will be covered for a period of six months.
If the goods are to be sent by a FREIGHT FORWARDER, send the goods
to:
Six months on all pan and tilts, scanners or preset lenses used in
continuousmotionapplications(thatis,presetscan,tourandautoscan
modes).
Pelco c/o Expeditors
473 Eccles Avenue
Pelco will warrant all replacement parts and repairs for 90 days from the
date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to Pelco, Clovis, California. Repairs made necessary by
reason of misuse, alteration, normal wear, or accident are not covered
under this warranty.
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
Pelco assumes no risk and shall be subject to no liability for damages or
loss resulting from the specific use or application made of the Products.
Pelco’s liability for any claim, whether based on breach of contract,
negligence, infringement of any rights of any party or product liability,
relating to the Products shall not exceed the price paid by the Dealer to
Pelco for such Products. In no event will Pelco be liable for any special,
incidental or consequential damages (including loss of use, loss of profit
and claims of third parties) however caused, whether by the negligence
of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The
Dealer may also have additional rights, which are subject to variation from
state to state.
If a warranty repair is required, the Dealer must contact Pelco at (800)
289-9100 or (559) 292-1981 to obtain a Repair Authorization number
(RA), and provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice
number
3. Details of the defect or problem If there is a dispute regarding the
warranty of a product which does not fall under the warranty conditions
stated above, please include a written explanation with the product
when returned.
Method of return shipment shall be the same or equal to the method by
which the item was received by Pelco.
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.
6
Pelco Manual C497M-D (1/96)
|