®
EH4700 Series
Environmental
Enclosures
Installation/
Operation Manual
C1405M-E (11/03)
In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150
International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120
GENERAL
IMPORTANT SAFEGUARDS AND WARNINGS
Prior to installation and use of this product, the following WARNINGS should be
observed.
1. Installation and servicing should only be done by qualified service personnel
and conform to all local codes.
2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or
6P enclosure, it is designed for indoor use only and it must not be installed
where exposed to rain and moisture.
3. Only use replacement parts recommended by Pelco.
4. After replacement/repair of this unit’s electrical components, conduct a resis-
tance measurement between line and exposed parts to verify the exposed
parts have not been connected to line circuitry.
5. The installation method and materials should be capable of supporting four
times the weight of the enclosure, pan/tilt, camera and lens combination.
The product and/or manual may bear the following marks:
This symbol indicates that dangerous voltage constituting a
risk of electric shock is present within this unit.
This symbol indicates that there are important operating and
maintenance instructions in the literature accompanying this
unit.
CAUTION:
RISK OF
ELECTRIC SHOCK.
DO NOT OPEN.
CAUTION:
TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER. NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
Please thoroughly familiarize yourself with the information
in this manual prior to installation and operation.
Pelco Manual C1405M-E (11/03)
3
DESCRIPTION
Environmental enclosures in the EH4700 Series are used with pan/tilt units or fixed
mounts. The enclosures are constructed of aluminum. You can install cameras with
either fixed focal length lenses or motorized zoom lenses (up to 10X). All models
have an adjustable camera sled to accommodate different sizes of cameras and
lenses.
MODELS
EH4718
Environmental enclosure with rear opening lid. Lid has gas
spring to hold it open. 18-inch (45.72 cm) length.
EH4718-1
EH4718-2
EH4718-3
EH4722
EH4718 with 120 VAC thermostatically controlled heater and
blower.
EH4718 with 24 VAC thermostatically controlled heater and
blower.
EH4718 with 230 VAC thermostatically controlled heater and
blower.
Environmental enclosure with rear opening lid. Lid has gas
spring to hold it open. 22-inch (55.88 cm) length.
EH4722-1
EH4722-2
EH4722-3
EH4722 with 120 VAC thermostatically controlled heater and
blower.
EH4722 with 24 VAC thermostatically controlled heater and
blower.
EH4722 with 230 VAC thermostatically controlled heater and
blower.
CERTIFICATIONS
The products identified below have been tested and certified for agency compli-
ance as noted.
Agency Compliance Certification
Model
CE
FCC
UL
CSA/cUL
EH4718
X
EH4718-1
EH4718-2
EH4718-3
EH4722
X
X
X
EH4722-1
EH4722-2
EH4722-3
X
X
Applicable CE, FCC, UL, and CSA/cUL directives/standards:
93/68/EEC – CE Mark Directive
•
89/336/EEC, 92/31/EEC – Electromagnetic Compatibility (EMC) Directives
EN 55022: 1984 Class B – Radio-frequency emissions limits
EN 50082-2: 1992 – Immunity standard
IEC 801-2: 1984 – ESD immunity
IEC 801-3: 1984 – Radiated field immunity
IEC 801-4: 1988 – Electrical transients
Additional applicable standards:
•
•
NEMA Type 3R
IP 32
4
Pelco Manual C1405M-E (11/03)
INSTALLATION
1. Unlatch and raise the enclosure lid. The gas spring will hold the lid in place
when it is fully opened.
2. Remove the camera sled from the rail:
a. Loosen the screws.
b. Slide the sled so that the screws are in the large part of the mounting
holes.
c. Remove the sled.
d. Remove the parts tied to the sled.
3. EH4718-1, -2, -3 Models, and EH4722 -1, -2, -3 Models Only - If you are
installing the enclosure in a marine or high-moisture environment, make the
following modifications to your enclosure:
Refer to Figure 1 for an exploded assembly diagram of the blower assembly.
a. Remove the two sets of screws and washers (A, B, and C) that secure
the fan shroud (3) to the bottom of the enclosure.
b. Remove the four screws (D) that secure the fan (4) to the back of the
enclosure.
Figure 1. Exploded Assembly Diagram for Blower and Circuit Board
Pelco Manual C1405M-E (11/03)
5
c. Move the fan out of the way and remove the fan shroud.
d. Turn the fan around so that it blows toward the viewing window (refer to
the arrows on the fan).
e. Reinstall the fan on the back of the enclosure.
f.
Close the enclosure lid.
g. On the bottom of the enclosure, remove the vent grills (1) and filter (2) at
the front and back of the enclosure. Replace the grills with the vent cover
plates that were attached to the camera sled as loose equipment.
h. Open the enclosure lid.
4. If you are going to wire the enclosure with cable, remove the wiring glands
and nuts from the parts bag and install them in the bottom of the enclosure. If
you are going to wire the enclosure with conduit, do not install the glands.
5. Mount the camera to the sled with the 1/4-20 Phillips-head screws that are
provided in the parts bag. You can mount the camera to either side of the sled.
Note that the edges of the sled are bent and that one lip is wide and the other
is narrow.
Normally you should mount the camera so that the wide lip of the sled fits over
the mounting screws.
If you are installing a camera with a low optical center line or a camera with a
large diameter lens, mount the camera so that the narrow lip of the sled fits
over the mounting screws. This elevates the sled.
6. There are two threaded mounting holes on the bottom of the enclosure. Mount
the enclosure to a pan/ tilt assembly or fixed mount with 1/4-20 screws with
threads that do not exceed 5/8 of an inch (1.59 cm) in length (not supplied with
the enclosure).
7. Install the sled and camera in the enclosure:
a. If the camera’s lens is adjustable, extend the lens to its maximum length.
b. Place the sled on the rail over the three attaching screws.
c. Slide the sled so that the screws fit into the narrow slots of the mounting
holes.
d. Tighten the screws just enough to hold the sled to the rail, but not too
tight to keep the sled from moving.
e. Slide the camera sled forward until the lens almost touches the window.
f.
Tighten the three screws to secure the camera sled to the rail.
8. Wire the video output from the camera.
9. If you are going to synchronize cameras, wire the camera’s synchronization
connection.
10. If your camera has a motorized zoom lens control, wire it.
EH4718 and EH4722 Models Only - Wire the camera’s lens control directly
to the lens controller.
EH4718-1, -2, -3 Models, and EH4722-1, -2, -3 Models Only - Refer to Fig-
ure 2 and wire the motorized zoom lens control as follows:
a. Connect or wire the lens control from the camera to the LENS or LENS
CONTROL connector on the circuit board.
6
Pelco Manual C1405M-E (11/03)
Figure 2. EH4700 Series Input Wiring Diagram
Pelco Manual C1405M-E (11/03)
7
b. Wire the 10-connector INPUTS terminal on the circuit board to the lens
controller as follows:
•
•
•
•
•
•
•
•
Lens Common - Connector 1
Focus - Connector 2
Zoom - Connector 3
Iris - Connector 4
Preset Common - Connector 5
Preset Focus - Connector 6
Preset Zoom - Connector 7
Preset High - Connector 8
11. EH4718-1, -2, -3 Models, and EH4722 -1, -2, -3 Models Only - Refer to
WARNING: Camera
damage possible. You can
damage your camera if you
connect it to the wrong
connector.
Figure 2 and connect the camera’s power input to the circuit board.
There are two ways to supply power to the camera: when the power require-
ments for the camera and enclosure’s accessories are the same (for example,
if the camera and accessories use 24 VAC), and when the power require-
ments for the camera and the enclosure’s accessories are different (for ex-
ample, if the camera uses 24 VAC and the accessories use 120 VAC).
If your camera will use the same
power as the enclosure, plug the
camera into the CAM 1 socket on the
circuit board inside the enclosure.
When the power requirements are the same, there are two ways to connect
power:
If your camera’s voltage will be dif-
ferent from the enclosure’s voltage,
plug the camera into the CAM 2
socket only. DO NOT plug the cam-
era into the CAM 1 socket or you can
damage your camera. CAM 1 has en-
closure voltage on it.
(1) A three-pin plug is supplied as loose equipment. Connect the wires from
the plug to the camera as follows:
Brown - AC HI
Blue - AC NT
Green - Ground
Connect the plug to the CAM 1 socket on the circuit board (remove the
plastic cover over the power supply section of the circuit board).
BE CAREFUL - REMEMBER
CAM 1 IS ENCLOSURE
POWER
or
(2) If both the camera end enclosure use 120 VAC and you ordered the
optional 120 VAC electrical outlet accessory (O/I-OUTLET), connect the
120 VAC plug to the camera and the three-pin plug to CAM 1 (remove
the plastic cover over the power supply section of the circuit board).
NEVER PLUG YOUR
CAMERA INTO CAM 1 IF
THE CAMERA’S VOLTAGE
IS DIFFERENT FROM THE
ENCLOSURE’S VOLTAGE.
When the power requirements are different, connect the wires from the
two-pin plug, which is supplied as loose equipment, to the camera as
follows:
Brown - AC HI
Blue - AC NT
Connect the plug to the CAM 2 socket on the circuit board.
12. Wire power to the enclosure to operate the camera.
EH4718 and EH4722 Models Only - Wire power directly to the camera. If you
are using 24 VAC, refer to Table A to determine the size of wire to use.
EH4718-1, -2, -3 Models, and EH4722-1, -2, -3 Models Only -
CAM 1 - If the camera’s power input is connected to CAM 1 on the circuit
board, go to step 13.
CAM 2 - If the camera’s power input is connected to CAM 2 on the circuit
board, wire power for the camera as follows:
a. Connect AC high to connector 9 of the 10-connector INPUTS terminal
block (goes to the brown wire in the CAM 2 connector).
b. Connect AC neutral to connector 10 of the 10-connector INPUTS termi-
nal block (goes to the blue wire in the CAM 2 connector).
8
Pelco Manual C1405M-E (11/03)
Table A. 24 VAC Wiring Distances
The following are the recommended maximum distances for 24 VAC applications
and are calculated with a 10-percent voltage drop. (Ten percent is generally the
maximum allowable voltage drop for AC-powered devices.)
Wire Gauge
EXAMPLE: An enclosure that re-
quires 80 vA and is installed 35 feet
(10 m) from the transformer would
require a minimum wire gauge of 20
Awg.
Total VA 20 AWG 18 AWG 16 AWG 14 AWG 12 AWG 10 AWG
(0.5mm2) (1.0 mm2) (1.5 mm2) (2.5 mm2) (4.0 mm2) (6.0 mm2)
10
283
(86)
451
716
1142
(348)
1811
(551)
2880
(877)
(137)
(218)
20
141
(42)
225
(68)
358
571
905
1440
(438)
(109)
(174)
(275)
NOTE: Distances are calculated in
feet; values in parentheses are
meters.
30
94
150
(45)
238
(72)
380
603
960
(28)
(115)
(183)
(292)
40
70
112
(34)
179
(54)
285
(86)
452
720
(21)
(137)
(219)
50
56
90
143
(43)
228
(69)
362
576
(17)
(27)
(110)
(175)
60
47
75
119
(36)
190
(57)
301
(91)
480
(14)
(22)
(146)
70
40
64
102
(31)
163
(49)
258
(78)
411
(12)
(19)
(125)
80
35
56
89
142
(43)
226
(68)
360
(10)
(17)
(27)
(109)
90
31
(9)
50
79
126
(38)
201
(61)
320
(97)
(15)
(24)
100
110
120
130
140
150
160
170
180
190
200
28
(8)
45
71
114
(34)
181
(55)
288
(87)
(13)
(21)
25
(7)
41
65
103
(31)
164
(49)
261
(79)
(12)
(19)
23
(7)
37
59
95
150
(45)
240
(73)
(11)
(17)
(28)
21
(6)
34
55
87
139
(42)
221
(67)
(10)
(16)
(26)
20
(6)
32
(9)
51
81
129
(39)
205
(62)
(15)
(24)
18
(5)
30
(9)
47
76
120
(36)
192
(58)
(14)
(23)
17
(5)
28
(8)
44
71
113
(34)
180
(54)
(13)
(21)
16
(4)
26
(7)
42
67
106
(32)
169
(51)
(12)
(20)
15
(4)
25
(7)
39
63
100
(30)
160
(48)
(11)
(19)
14
(4)
23
(7)
37
60
95
151
(46)
(11)
(18)
(28)
14
(4)
22
(6)
35
57
90
144
(43)
(10)
(17)
(27)
Pelco Manual C1405M-E (11/03)
9
13. EH4718-1, -2, -3 Models, and EH4722-1, -2, -3 Models Only - Wire power to
the enclosure to operate accessories (and the camera if its power is con-
nected to CAM 1 on the circuit board) as follows:
a. Remove the plastic cover over the power supply section of the circuit
board.
b. Connect AC high to AC HI of the 3-connector terminal block.
c. Connect AC neutral to AC NT of the 3-connector terminal block.
d. Connect ground to GND of the 3-connector terminal block.
e. Reinstall the plastic cover over the power supply section of the circuit
board.
If the camera’s power is connected to CAM 1 on the circuit board, add the
camera’s wattage to the power consumption of the accessories to determine
the size of wire to use. If you are using 24 VAC, refer to Table A to determine
the size of wire to use. Here are the wattages for the accessories:
•
•
•
•
•
Blowers for all enclosures - 8 watts
Defrosters for all enclosures - 15 watts
Heaters for 120 VAC enclosures - 60 watts
Heaters for 24 VAC enclosures - 50 watts
Heaters for 230 VAC enclosures - 55 watts
14.
15.
Adjust the camera focus and iris, if necessary.
Close the enclosure lid.
10
Pelco Manual C1405M-E (11/03)
OPERATION
If your enclosure has a thermostatically controlled blower, the thermostat is set to
turn the fan on between 77° and 93°F (25° and 34°C) and to turn the fan off
between 62° and 78°F (17° and 26°C).
If your enclosure has thermostatically controlled heaters or defroster, the thermo-
stat is set to turn them on between 42° and 58°F (6° and 14°C) and to turn them
off between 72° and 88°F (22° and 31°C).
Pelco Manual C1405M-E (11/03)
11
MAINTENANCE
Perform the following maintenance at regularly scheduled intervals to prolong the
operational life and appearance of the equipment.
1. Clean the window with a mild nonabrasive detergent in water and a soft cloth
to maintain picture clarity.
2. If your enclosure has a blower, clean the foam filter as follows:
a. On the bottom front of the enclosure, remove the two screws in the vent
grill.
b. Remove the vent grill and take out the filter.
c. Clean the filter with warm water and mild detergent, dry thoroughly, and
replace it in the grill.
d. Reinstall the vent grill.
To order replacement filters, use the part number EH470010009.
SERVICE MANUAL
If you need to service your unit, obtain a service manual in on of the following ways:
•
•
C1405SM.
Contact Pelco’s Literature Department and request service manual C1405SM.
SPECIFICATIONS
12
Pelco Manual C1405M-E (11/03)
ELECTRICAL
Input Voltage:
24, 120 or 230 VAC, 50/60 Hz
Electrical
Connections:
One each of the following when equipped with optional circuit
board (O/I-PCB):
3-connector terminal block for power input
6-pin lens connector
9-connector terminal block for lens wiring
10-connector terminal block for camera/lens wiring
2-connector terminal block for spare connections
3-pin socket for camera power input
2-pin socket for optional camera power input
2-pin socket for blower
2-pin socket for defroster
4-pin socket for heaters
Input Power:
Heater-1
Heater-2
Heater-3
Defroster
Blower
60 watts
50 watts
55 watts
15 watts
8 watts
MECHANICAL
Construction:
Finish:
Die-cast, extruded, and sheet aluminum
Polyester powder coat, 2-tone gray
Cable Entry:
Two UL-approved glands on bottom of enclosure; maximum
cable diameter 0.47 inch (1.19 cm). Will accept 1/2-inch (1.27
cm) conduit without glands.
Window:
Plastic
Window
Viewing Area:
3.50" H x 4.00" W
(8.89 x 10.16 cm)
Camera
Mounting:
Removable camera sled that can be inverted to accommodate
various heights of cameras and lenses
Maximum
Camera/Lens
Size:
Accommodates camera/lens combinations (including BNC
connector) up to:
EH4718
17" L x 5.5" W x 4.25" H
Pelco Manual C1405M-E (11/03)
13
(43.18 x 13.97 x 10.80 cm)
EH4718-1, -2, -3
13" L x 4.75" W x 4.25" H
(33.02 x 12.07 x 10.80 cm)
EH4722
21" L x 5.5" W x 4.25" H
(53.34 x 13.97 x 10.80 cm)
EH4722-1, -2, -3
17" L x 4.75" W x 4.25" H
(43.18 x 12.07 x 10.80 cm)
Rear Latch:
Dimensions:
Stainless Steel
See Figure 3
Weight:
Unit
Shipping
EH4718
EH4718-1, -2, -3
EH4722
7.25 lb (3.28 kg)
8.5 lb (3.85 kg)
8.5 lb (3.85 kg)
9.75 lb (4.42 kg)
9 lb (4.08 kg)
10 lb (4.53 kg)
10 lb (4.53 kg)
12 lb (5.44 kg)
EH4722-1, -2, -3
GENERAL
Environment:
Indoor/outdoor
-10° to 120°F (-23° to 49°C)
Temperature
Figure 3. EH4700 Dimension Drawing
14
Pelco Manual C1405M-E (11/03)
increase inside
enclosure with
heater operating: With vent grills installed:
17°F (9.5°C) increase
With vent covers and TI47
thermal installation:
25°F (13.8°C) increase
With vent covers, TI47
thermal insulation and
WD47 defroster installed:
35°F (19.4°C) increase
Ratings:
NEMA Type 3R
IP 32
Pelco Manual C1405M-E (11/03)
15
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.
If
a
warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following
information:
1. Model and serial number
Exceptions to this warranty are as noted below:
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
•
•
•
Five years on FT/FR8000 Series fiber optic products.
Three years on Genex® Series products (multiplexers, server, and keyboard).
If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product
when returned.
Three years on Camclosure® and fixed camera models, except the CC3701H-2,
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,
which have a five-year warranty.
Method of return shipment shall be the same or equal to the method by which the item was
received by Pelco.
•
•
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series
fixed dome products.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned
for credit, and RA number if returned for repair).
•
Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in
continuous motion applications.
•
•
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.
Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura™ Series distributed network-based video products.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.
•
•
One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from
the specific use or application made of the Products. Pelco’s liability for any claim, whether
based on breach of contract, negligence, infringement of any rights of any party or product
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for
such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused,
whether by the negligence of Pelco or otherwise.
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors
473 Eccles Avenue
The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
REVISION HISTORY
Manual #
Date
Comments
C1405M
10/94
Original version.
C1405M-A
C1405M-B
C1405M-C
12/94
8/95
3/96
7/96
Revised to include new PCB9000276 wiring diagram and parts list as per ECO#94-578.
Revised Figure 1 to include new PCB9000277ASSY per ECO# 95-255. Revised Figure 9 and Section 4.1.5.
Expanded installation instructions; added troubleshooting section; changed heater specifications.
Changed specification for maximum camera size in -1, -2 and -3 models. Updated Figure 3 and respective table to show added 24
VDC rectifier per ECO # 96-159.
9/96
5/98
Added temperature specifications when using heater, TI47 thermal insulation and WD47 defroster.
Removed installation instructions for accessories, which have a separate manual. Moved service information and exploded as-
sembly drawings to new manual, C1405SM. Changed manual to new format.
C1405M-D
C1405M-E
11/03
Updated certifications, corrected weight specification, and removed section numbering.
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.
Endura and ExSite are trademarks of Pelco.
© Copyright 2003, Pelco.
All rights reserved.
16
Pelco Manual C1405M-E (11/03)
|