I N S T A L L A T I O N
SWM Series Spectra®
Compact Wall Mount
C293M-B (1/09)
Installation
The SWM can be mounted directly onto a wall, onto a single gang electrical box, or onto a pole using an
adapter. Refer to the SWM-PA Series pole adapter manual (C294M) for pole mounting installation
instructions.
WALL MOUNTING
To install the SWM Series wall mount directly onto a wall (refer to Figure 1 on page 4):
1. Determine the location where the mount is to be installed.
2. Use the adjustment plate as a template to drill holes into the mounting surface. If the adjustment
plate is not required for shimming, it can be discarded after the mounting holes are drilled.
3. Pull the electrical cables from the cable hole in the mounting surface through the cable holes in the
adjustment plate (if required), and then through the mounting cleat. Position the cleat so the
elongated mounting fastener hole is below the cable entry hole and the embossed arrow is pointing
up.
4. Fasten the adjustment plate (if used) and mounting cleat securely to the mounting surface with two
fasteners of appropriate length and size (not supplied). If necessary, before tightening the two
fasteners, insert shims between the adjustment plate and the mounting surface to create a
perpendicular surface on which to attach the wall mount. The lower hole in the mounting cleat is
elongated, which allows for vertical alignment adjustment.
5. Pull the electrical cables through the mount, hook the mount onto the top of the mounting cleat, and
position the mount flush against the mounting surface. If necessary, loosen the set screw to ensure
the mount is flush against the mounting surface. Tighten the set screw in the bottom of the mount
only until the mount is snug against the surface. Do not overtighten.
C293M-B (1/09)
3
6. Attach the pendant model back box to the mount:
a.
b.
c.
d.
Pull the electrical cables from the mount into the back box.
Apply anti-seize lubricant (supplied) to the back box pipe threads.
Screw the back box into the threads in the mount.
Complete the installation using the instructions in the dome manual.
MOUNTING CLEAT
MOUNTING FASTENERS
(NOT SUPPLIED)
WALL MOUNT
ADJUSTMENT
PLATE
10-24 SET SCREW
Figure 1. Installing the SWM Series Wall Mount onto a Wall
4
C293M-B (1/09)
ELECTRICAL BOX MOUNTING
To install the SWM Series wall mount onto a single gang electrical box (refer to Figure 2 on page 5):
1. Thread the two inner mounting holes on the adjustment plate to be used with threaded mounting
fasteners (not supplied).
2. Pull the electrical cables from the gang box through the cable hole in the adjustment plate.
3. Fasten the adjustment plate to the mounting surface with two fasteners of appropriate length and
size (not supplied).
4. Pull the electrical cables from the gang box through the cable hole in the mounting cleat. Position
the cleat so the elongated mounting fastener hole is below the cable entry hole and the embossed
arrow is pointing up.
5. Fasten the mounting cleat to the adjustment plate with two threaded fasteners of appropriate
length and size (not supplied).
6. Pull the electrical cables through the mount, hook the mount onto the top of the mounting cleat, and
position the mount flush against the mounting surface. If necessary, loosen the set screw to ensure
the mount is flush against the mounting surface. Tighten the set screw in the bottom of the mount
only until the mount is snug against the surface. Do not overtighten.
7. Attach the pendant model back box to the mount:
a.
b.
c.
d.
Pull the electrical cables from the mount into the back box.
Apply anti-seize lubricant (supplied) to the back box pipe threads.
Screw the back box into the threads in the mount.
Complete the installation using the instructions in the dome manual.
MOUNTING CLEAT
MOUNTING FASTENERS
(NOT SUPPLIED)
WALL MOUNT
ADJUSTMENT
PLATE
10-24 SET SCREW
Figure 2. Installing the SWM Series Wall Mount onto an Electrical Box
C293M-B (1/09)
5
Specifications
MECHANICAL
Construction
Cast aluminum
Finish
SWM-GY
SWM-BK
Gray polyester powder coat
Black polyester powder coat
Mount Method
Mount is secured by a set screw to a mounting cleat that is
attached to a surface with two fasteners (not supplied). A gasket
is affixed to the base to protect the interior from moisture. An
adjustment plate is provided to allow the wall mount to be
shimmed when the mounting surface is not plumb. The lower
hole in the mounting cleat is elongated, which allows for vertical
alignment adjustment.
Dome Mounting
Cable Entry
1-1/2-inch NPT pipe thread in mount tip. Anti-seize lubricant is
supplied to be applied to the pipe threads.
One cable feedthrough hole in the mounting cleat. Cable feeds
through the mount into the pendant dome.
Maximum Load
10 lb (4.5 kg)
GENERAL
Environment
Indoor/outdoor
Weight
Unit
Shipping
1.1 lb (0.50 kg)
2.0 lb (0.91 kg)
(Design and product specifications subject to change without notice.)
4.15
(10.54)
2.54
(6.45)
6.25
(15.88)
3.10
(7.87)
NOTE: VALUES IN PARENTHESIS ARE CENTIMETERS; ALL OTHERS ARE INCHES.
Figure 3. Dimension Drawing
6
C293M-B (1/09)
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of
shipment.
Exceptions to this warranty are as noted below:
•
•
Five years:
–
–
–
Fiber optic products
TW3000 Series unshielded twisted pair (UTP) transmission products
CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models
Three years:
–
–
–
–
–
Pelco-branded fixed camera models (CCC1390H Series, C10DN Series, C10CH Series, and IP3701H Series)
EH1500 Series enclosures
Spectra® IV products (including Spectra IV IP)
Camclosure® Series (IS, ICS, IP) integrated camera systems
DX Series digital video recorders, DVR5100 Series digital video recorders, Digital Sentry® Series hardware products, DVX Series digital video
recorders, and NVR300 Series network video recorders
–
–
–
Endura® Series distributed network-based video products
Genex® Series products (multiplexers, server, and keyboard)
PMCL200/300/400 Series LCD monitors
•
Two years:
–
–
–
–
–
–
–
–
Standard varifocal, fixed focal, and motorized zoom lenses.
DF5/DF8 Series fixed dome products
Legacy® Series integrated positioning systems
Spectra III™, Spectra Mini, Spectra Mini IP, Esprit®, ExSite®, and PS20 scanners, including when used in continuous motion applications.
Esprit Ti and TI2500 Series thermal imaging products
Esprit and WW5700 Series window wiper (excluding wiper blades).
CM6700/CM6800/CM9700 Series matrix
Digital Light Processing (DLP®) displays (except lamp and color wheel). The lamp and color wheel will be covered for a period of 90 days.
The air filter is not covered under warranty.
–
Intelli-M® eIDC controllers
•
•
One year:
–
Video cassette recorders (VCRs), except video heads. Video heads will be covered for a period of six months.
Six months:
–
All pan and tilts, scanners, or preset lenses used in continuous motion applications (preset scan, tour, and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to a Pelco designated location. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under
this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products.
Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to
the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental, or
consequential damages (including loss of use, loss of profit, and claims of third parties) however caused, whether by the negligence of Pelco or
otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state
to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and
provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, sales order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product that does not fall under the warranty conditions stated above, please include a written
explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.
RETURNS
To expedite parts returned for repair or credit, please call Pelco at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if
returned for credit, and RA number if returned for repair) and designated return location.
All merchandise returned for credit may be subject to a 20 percent restocking and refurbishing charge.
12-23-08
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid
REVISION HISTORY
Manual #
C293M
Date
11/98
12/07
1/09
Comments
Original version.
C293M-A
C293M-B
Updated to new format. Revised Figure 1 to include additional holes in adjustment plate.
Reformatted manual to smaller size.
Pelco, the Pelco logo, Camclosure, Endura, Esprit, ExSite, Genex, Legacy, and Spectra are registered trademarks of Pelco.© Copyright 2007, Pelco. All
rights reserved.
Spectra III is a trademark of Pelco.
DLP is a registered trademark of Texas Instruments Incorporated.
Pelco, Inc. Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA
USA & Canada Tel (800) 289-9100 Fax (800) 289-9150
International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120
|