I N S T A L L A T I O N
PMCL-R Series
Monitor Mount
C2220M-A (1/06)
Installation
The following parts are supplied:
Qty
2
Description
Preassembled rack mounts
8
Screws, 10-32 x 0.750-inch, Phillips, pan head, black
Nylon washers
8
4
Screws, M4 x 0.70 x 6 mm, Phillips, pan head, stainless steel
Lock washers
4
1. Tighten the lock nuts (refer to Figure 1) so they are loose enough to allow the brackets to move but tight enough to hold them in place.
2. Attach the rack mounts to the monitor using the four stainless steel, pan head screws and lock washers. Refer to Figure 1.
(4) LOCK WASHERS
(4) SCREWS,
M4 X 0.70 X 6MM,
PHILLIPS, PAN HEAD
(2) LOCK NUTS
Figure 1. Attaching Rack Mounts to Monitor
3. Attach the rack mounts to the equipment rack using the eight black, pan head screws and nylon washers. Align the top slots of the mounts
with mounting holes on the equipment rack that have 0.5-inch spacing below them. All eight mounting slots will align with the holes in the
rack only if the mounts are in the correct position.
4. Swivel the monitor forward or backward to position it to the proper viewing angle.
C2220M-A (1/06)
3
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following
information:
Exceptions to this warranty are as noted below:
1. Model and serial number
•
Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted
pair transmission products.
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
•
•
•
Three years on Spectra® IV products.
If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product when
returned.
Three years on Genex® Series products (multiplexers, server, and keyboard).
Three years on Camclosure® and fixed camera models, except the CC3701H-2,
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,
which have a five-year warranty.
Three years on PMCL200/300/400 Series LCD monitors.
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed
dome products.
Two years on Spectra III™, Esprit®, ExSite™, and PS20 scanners, including when used in
continuous motion applications.
Method of return shipment shall be the same or equal to the method by which the item was
received by Pelco.
•
•
•
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for
credit, and RA number if returned for repair).
•
•
•
Two years on Esprit and WW5700 Series window wiper (excluding wiper blades).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.
Two years (except lamp and color wheel) on Digital Light Processing (DLP®) displays.
The lamp and color wheel will be covered for a period of 90 days. The air filter is not
covered under warranty.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.
•
•
•
Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura™ Series distributed network-based video products.
One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed
to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from
the specific use or application made of the Products. Pelco’s liability for any claim, whether
based on breach of contract, negligence, infringement of any rights of any party or product lia-
bility, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such
Products. In no event will Pelco be liable for any special, incidental or consequential damages
(including loss of use, loss of profit and claims of third parties) however caused, whether by
the negligence of Pelco or otherwise.
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.
REVISION HISTORY
Manual #
C2220M
C2220M-A
Date
11/05
1/06
Comments
Original version.
Added information about aligning mounting holes properly.
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.
Endura, ExSite, and Spectra III are trademarks of Pelco.
© Copyright 2006, Pelco. All rights reserved.
DLP is a registered trademark of Texas Instruments, Inc
USA & Canada • Tel: 800/289-9100 • Fax: 800/289-9150
International • Tel: 1-559/292-1981 • Fax: 1-559/348-1120
|