%.
5SER MANUAL
Important Information
EN
For your safety
In the event of a power failure, you cannot use this handset to make or receive calls. Alternative arrangements
should be made for access to emergency calls.
Your PIN code is preset to 0000. If you change your PIN code, keep the PIN details in a safe place where you
have easy access to them. Do not lose the PIN code.
To avoid damage or malfunction:
- Do not allow the product to come into contact with liquid.
- Do not open it as you could be exposed to high voltages.
- Never use any battery type other than the one supplied.
- Do not expose the phone to excessive heat caused by heating equipment or direct sunlight.
- Do not drop your phone or allow objects to fall on your phone.
-
Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives as these may harm the set.
- Active mobile phones in the vicinity may cause interference.
- Do not use the product in places where there are explosive hazards.
- Do not let small metal objects come into contact with the product. This can deteriorate audio quality
and damage the product.
About operating and storage temperatures:
- Operate in a place where temperature is always between 0 and 35º C (32 to 95º F).
- Store in a place where temperature is always between -20 and 45º C (-4 to 113º F).
- Battery life may be shortened in low temperature conditions.
Installation requirements
This product requires an electrical supply of 220-240 volts, alternating monophased power, excluding IT
installations defined in standard EN 60-950. In case of power failure, the communication can be lost.
The electrical network is classified as hazardous according to criteria in the standard EN 60-950. The only way
to power down this product is to unplug the power supply unit from the electrical outlet. Ensure the electrical
outlet is located close to the apparatus and is always easily accessible.
The voltage on the network is classified as TNV-3 (Telecommunication Network Voltages), as defined in the
standard EN 60-950.
Need Help?
For more information on troubleshooting and FAQs:
Troubleshooting: page 51
Online Help
4
What’s in the box?
EN
The following accessories are included with your SE630:
Power supply for
base station
Base station
Line cord
Handset
Warranty card
Battery door
Quick Start
Guide
User Guide
2 AAA
rechargeable
batteries
The line adaptor may not be attached to the line cord. In this case, you have to connect the line adaptor
to the line cord first before plugging the line cord to the line socket.
In multihandset packs, you will find one or more additional handsets, chargers with power supply units
and additional rechargeable batteries.
5
Your SE630
EN
Handset keys
Press
To
Enter the main menu from stand-by mode.
Select the function displayed on the handset screen directly above it.
Activate mute function during a call.
m
Go to redial list from stand-by mode.
Select the function displayed on the handset screen directly above it.
>
r
e
Answer an incoming external or internal call.
Insert R for operator services when on the line.
Hang up a call.
Long press from menu browsing to return to stand-by mode, short press to return to
previous menu.
Long press in stand-by mode to switch off the handset, short press to switch on the hand-
set again.
Access call log from stand-by mode.
Scroll up a menu list or go to the previous phonebook or call log record.
Increase earpiece volume during a call.
u
d
Go to the previous character in editing mode.
Access phonebook from stand-by mode.
Scroll down a menu list or go to the next phonebook or call log record.
Decrease earpiece volume during a call.
Go to the next character in editing mode.
Initiate an internal call.
c
v
#
Answer an incoming call in handsfree mode.
Activate and deactivate the loudspeaker* during a call.
Dial # in stand-by mode.
Long press to mute the ringer in stand-by mode.
Insert a pause in dialling mode.
Switch between upper and lower case in editing mode.
Dial * in stand-by mode.
Long press to activate and deactivate keypad lock.
*
Soft key
>BACK
Short press from menu browsing to return to the previous menu.
*WARNING Handsfree activation can suddenly increase the volume in the earpiece to a very high
level. Make sure the handset is not too close to your ear.
7
Your SE630
EN
Display icons & symbols
In stand-by mode, several icons & symbols may be displayed on the handset.
The handset is registered and within range of the base station. It blinks when the handset is
out of range or is searching for a base.
Battery symbol indicating 3 different battery levels.
The ringer volume is set to zero.
There is an external incoming call, an external call is connected or an external call is held.
There is an internal incoming call, an internal call is connected or an internal call is held.
The loudspeaker is ON.
Alarm clock is activated.
Blinks when there is a missed call, or when new SMS or voicemail messages are received
and not read yet. Steady when there are received SMS messages in the SMS box.
8
Your SE630
EN
Overview of the base station
Paging key
SIM card tray
Main features of your SE630
The following is an overview of the menu options that are available in your SE630. For detailed explanation of
the menu options, please refer to the corresponding sections in this User Guide.
Menu
To
Page
SMS
Setup, write/read SMS, etc
27
PHONEBOOK
Add, edit and manage phonebook entries
Set date and time, alarm and alarm tone
21
34
CLOCK &
ALARM
PERSONAL SET
Set Handset tone, Wallpaper, Contrast level, Screensaver,
Handset name, Auto pickup/Hang-up, Languages and Babysit
mode
35
40
ADVANCED
SET
Set Recall time, Dial mode, Call barring, Baby call mode,
Register/Unregister handset, Select Base, Change PIN, Reset
phone, Auto prefix, Country and Conference mode
NET. SERVICE
GAMES
Set Call forwarding, Voice mail, Call back, Caller ID
Play games
47
50
9
Your SE630
Menu navigation
EN
The basic steps of navigating through the menus and options are as follows:
Task
Action
Illustration
Enter main menu/menu
options.
Choose MENU by pressing the
key directly below it (left soft
key m).
1
Philips
18:00
08-08
MENU
REDIAL
>
m
:
• Go to
option
a
specific menu/ 1. Press : key to scroll to
SMS
your desired menu/option.
• Confirm your selection
2. Choose
SELECT
by
pressing the key directly
below it (left soft key
m).
SELECT
BACK
ꢀ
:
>
m
1
2
In this example, the alarm is On
Once.
Alarm
Off
On Once
On Daily
• To change your selection
• To confirm your selection
1. Press : key to scroll to
your desired option.
2. Choose
SELECT
by
pressing the key directly
below it (left soft key
ꢁ
ꢀ
BACK
SELECT
m).
>
m
:
• Return to previous menu
level or stand-by screen
3. Choose BACK by pressing
the key directly below it
1
3
(right soft key >).
2
10
Connect
EN
The location of your base station can have an effect on the range and performance of your SE630 (see TIP
below).
Connecting the Base Station
1. Place the base station in a central location near the telephone line socket and electricity sockets.
2. Connect the line cord and the power cable to the proper connector at the back of the base station.
1.
2.
B
A
Connect the
A
power supply
Connect
the line cord to
the line socket
B
3. Connect the other end of the line cord to the telephone line socket and the other end of the power cable
to the electricity socket.
The line adaptor may not be attached to the line cord. In this case, you have to connect the line
adaptor to the line cord first before plugging the line cord to the line socket.
TIP Avoid placing the base station too close to large metal objects such as filing cabinets, radiators or
electrical appliances. This can impair the range and sound quality. Buildings with thick internal and
external walls may impair transmission of signals to and from the base.
WARNING The base station does not have an ON/OFF switch. Power is applied when the power
adaptor is plugged into the unit and connected to the electricity socket. The only way to power
down the unit is to unplug the power adaptor from the electricity socket. Therefore, ensure that the
electricity socket is easily accessible.
The power adaptor and telephone line cord have to be connected correctly, as incorrect
connection could damage the unit.
Always use the telephone line cord supplied with the unit. Otherwise, you may not get a dial tone.
11
Install
EN
Install battery
Your SE630 is supplied with 2 rechargeable batteries allowing approximately up to 12 hours of talk-time and
up to 150 hours stand-by time. Before using the handset, the batteries have to be installed and fully charged.
1. Slide out the battery cover.
2. Place the batteries as indicated and replace the cover.
Charge battery
1. Place the handset on the charging cradle of the base station. A beep is emitted if the handset is placed
correctly.
2. A charging animation on the handset indicates that the battery is charging.
1
Philips
08-08
MENU
18:00
REDIAL
3. Leave it there until the batteries are fully charged (at least 24 hours).
4. The handset is fully charged when the charging animation stops and
is displayed.
The handset must be charged for at least 24 hours before using it for the first time.
12
Install
EN
Battery life and range
Talk time and stand-by time
When the battery is fully charged, the talk time of your SE630 is approximately 12 hours and the stand-by time
is approximately 150 hours.
Low battery warning
The battery level is shown at the top left of the handset screen. When the battery level becomes low, the low
battery sensor alerts you by sounding an audible tone and blinking the battery icon.
If the battery level becomes exceedingly low, the phone automatically switches off shortly after the alert and
any function in progress will not be saved.
The approximate power levels of your battery are indicated as follows:
Battery is fully charged - 3 bars in the battery icon
Battery is partially charged - 2 bars in the battery icon
Battery is running low - 1 bar in the battery icon
Battery is fully discharged - 0 bar in the battery icon
Out of range warning
The indoor and outdoor range of the phone is up to 50 metres and 300 metres respectively. When the
handset moves beyond operation range, the antenna icon
will blink.
Configure your SE630
Before you use your SE630, you need to configure it according to the country of use. After charging it for a few
minutes, the WELCOME screen appears. Follow these steps to configure your phone:
1. Press any key to display the list of countries.
2. Scroll : to your country.
3. Press mSELECT to confirm your selection.
4. Scroll : to your operator (if necessary).
5. Press mSELECT again to confirm your selection.
6. The default line settings and menu language for the selected country will be automatically configured.
You can still make outgoing calls or receive incoming calls without first defining your country
selection.
Depending on your country, the WELCOME screen may not appear. In this case, you are not
required to select your country/operator/language settings.
13
Install
EN
Set date and time
1. Press mMENU.
2. Scroll : to Clock & Alarm and press mSELECT.
3. Press mSELECT to enter Set Date/Time.
4. Enter current time (HH:MM) and current date (DD/MM/YY) and press mSELECT.
be updated after each call. The availability of date & time update is dependent on your network
provider. Please check the date & time settings in your ISDN system or contact your network
provider.
Now, you are ready to use your phone.
Basic operations of your SE630
Make a call
Enter the phone number (maximum 24 digits) and press r to dial the number.
For details, please refer to "Make a call" on page 17.
Answer or end a call
Press r key to answer a call.
Presse key to end a call.
For details, please refer to "Answer a call" and "End a call" on page 18.
Switch the handset on/off
Press and hold e key for 5 seconds to switch off the handset in stand-by mode.
Short press e key to switch on the handset again.j
Keypad lock/unlock
Press and hold * key for 2 seconds to lock and unlock the keypad in stand-by mode.
Paging
The paging feature enables you to locate a missing handset if the handset is in range and contains
charged batteries.
Press c key on the base until the handset starts to ring.
Once retrieved, press e to end the paging.
14
Install
EN
Stand-by mode
If the handset is idle for 30 seconds in settings mode, review mode, edit mode, etc. it will automatically return
to stand-by mode. It will also return to stand-by mode automatically when the handset is placed back on the
base station.
Screen and keypad backlight
The backlight remains on for 20 seconds after each activation such as an incoming call, key presses, lifting up
the handset off the base station, etc. The color of the keypad backlight is AMBER.
Event LED
If you have subscribed to Caller Line identification, the event LED on your handset blinks when there is a new
event such as a new call, a new SMS or a new voice mail message.
Text and number entry
Key
Assignment
space 1 @ _ # = < > ( ) & £ $ ¥ [ ] { } ¤ §
1
2
3
4
5
6
7
8
9
0
a b c 2 à ä ç å æ
d e f 3 é è ∆ Φ
g h i 4 ì Γ
j k l 5 Λ
m n o 6 ñ ò ö
p q r s 7 β Π Θ Σ
t u v 8 ù ü
w x y z 9 ø Ω Ξ Ψ
. 0 , / : ; “ ‘ ! i ? * + - % \ ^ ~|
For example, to enter the name “Philips”:
1. Press 7 once: P
2. Press 4 twice: Ph
3. Press 4 three times: Phi
4. Press 5 three times: Phil
5. Press 4 three times: Phili
6. Press 7 once: Philip
15
Install
EN
7. Press 7 four times: Philips
By default, the first letter of a word is in upper case. Press # to switch between upper and
lower case.
Default settings
Ringer Volume
Earpiece Volume
Speaker Volume
Key Beep
Medium
Volume 3
Volume 3
On
Wallpaper
Contrast
Level 2
On
Screensaver
Auto Pick-up
Auto Hang-up
Babysit mode
Alarm clock
Barring mode
SMS reception
Master PIN
Off
On
Off
Off
Off
On
0000
16
Call
EN
Make a call
Predialling
1. Enter the phone number (maximum 24 digits).
2. Press r to dial the number.
Direct dialling
1. Press r or v to take the line.
2. Enter the phone number.
Call from redial list
1. Press > in stand-by mode.
2. Scroll : to an entry in the redial list.
3. Press r to dial the number.
TIP The handset stores the last 20 numbers dialled. The last number dialled will appear first in the
redial list. If the redial number matches a phonebook entry, the name will be displayed instead.
Call from the call log
1. Press u in stand-by mode.
2. Press mSELECT to enter call log.
3. Scroll : to an entry in the call log.
4. Press r to dial the number.
You need to subscribe to Caller Line Identification service to be able to see the caller’s number or
name in the call log. See "Call log" on page 25 for details.
Call from the phonebook
1. Press d in stand-by mode.
2. Scroll : to a phonebook entry.
3. Press r to dial the number.
TIP Instead of scrolling : to browse the phonebook entries, press the numeric key corresponding
to the first letter of the entry you wish to locate. For example, pressing 2 will show the entries
starting with A. Pressing 2 again will show the entries starting with B, etc...
17
Call
EN
Answer a call
When the phone rings, press r key.
Handsfree answering
When the phone rings, press v key.
Incoming call has priority over other events. Whenever there is an incoming call, other status in
progress such as phone setting, menu navigation, etc will be aborted.
TIP If Auto Pick-up mode (see page 38) is activated, you can simply lift up the handset from its base
station to answer the call. This feature is deactivated by default.
WARNING When the handset rings during an incoming call, please do not hold the handset too
close to your ear as the volume of the ringing tone may damage your hearing.
End a call
Press e key.
The call duration will be displayed on the handset screen for about 5 seconds.
TIP If Auto Hang-up mode (see page 38) is activated, you can simply place the handset back to its
base station to end the call. This feature is activated by default.
Calls in-progress
The following options are available during a call:
Adjust earpiece volume
1. Press : to select from Volume 1 to Volume 5.
Mute/unmute the handset
1. During a call, press mMUTE to turn off the microphone so that your correspondent cannot hear you.
2. Press mUNMUTE to turn on the microphone.
Loudspeaker mode
1. Press v key to activate loudspeaker mode.
18
Call
EN
2. Press v key again to return to normal mode.
WARNING Activation of loudspeaker can suddenly increase the volume in the earpiece to a very
high level. Make sure the handset is not too close to your ear.
Adjust loudspeaker volume
1. Press : key to select from Volume 1 to Volume 5.
Intercom
This feature is only available when there are at least 2 registered handsets. It allows you to make free internal
calls, transfer external calls from one handset to another and use the conference option.
Intercom another handset
To be able to use intercommunication feature, you must have at least 2 handsets registered to your base
station (see page 43 "To register an additional handset").
1. Press c key in stand-by mode.
2. Intercom is established immediately if there are only 2 registered handsets. If there are more than 2 regis-
tered handsets, the handset numbers which are available for intercom will be displayed. Press mALL to
call all the handsets or press the handset number to select a specific handset, e.g. press 2 to call
handset 2.
If the handset does not belong to keep the same range, this function may not be available.
Transfer an external call to another handset
1. Press c key to put the external call on hold (the caller can no longer hear you).
2. Intercom is established immediately if there are only 2 registered handsets. If there are more than 2 regis-
tered handsets, the handset numbers which are available for intercom will be displayed. Press mALL to
call all the handsets or press the handset number to select a specific handset, e.g. press 2 to call
handset 2.
The called handset rings.
If there is no answer from the called handset, press c key to resume the external call.
3. Press r key on the called handset to answer the internal call, where both internal callers can talk.
4. Presse key on the first handset to transfer the external call to the called handset.
Switch between an internal and external call
1. Press c key once to switch between an internal call and external call.
19
Call
EN
Three-party conference call
The conference call feature allows one external call to be shared with two handsets (in intercom). The three
parties can share the conversation and no network subscription is required.
1. Press c to put the external call on hold (the caller can no longer hear you).
2. Intercom is established immediately if there are only 2 registered handsets. If there are more than 2 regis-
tered handsets, the handset numbers which are available for establishing a conference call will be
displayed. Press mALL to call all the handsets or press the handset number to select a specific handset,
e.g. press 2 to call handset 2.
The called handset rings.
3. Press r key on the called handset to answer the internal call, where both internal callers can talk.
4. Press CONF soft key on the first handset to start the three-party conference.
TIP If Conference mode is activated (see page 46), a three-party conference call is automatically
established if the second handset takes the line when there is already an external call in progress.
Call waiting
If you have subscribed to Call Waiting service, the earpiece will emit a beep tone to inform you that there is a
second incoming call. The number or name of the second caller will also be displayed if you have subscribed to
Caller Line Identification service (CLI). Please contact your network provider for more information on this
service.
To answer the second call, press r+ 2(may be different according to your network).
Caller Line Identification
Caller Line Identification (CLI) is a special service that you may subscribe from your network operator. If you
have subscribed to CLI service, and provided the identity of the caller is not withheld, the number or name of
the caller (if stored in the phonebook) will be displayed when the phone rings so that you may decide whether
to answer the call or not. Please contact your network provider for more information on this service.
20
Phonebook
EN
Phonebook
New Entry
List Entry
Edit Entry
Delete Entry
Delete All
Direct Memory
Copy from SIM
Phbk transfer
Your SE630 can store up to 250 phonebook memories, including 9 direct access memories (1 to 9).
Each phonebook entry can have a maximum of 24 digits for the phone number and 12 characters for name.
Access phonebook
1. Press d in stand-by mode or press mMENU, scroll : to Phonebook and press mSELECT, scroll
: to List Entry and press mSELECT.
2. The phonebook entries will be listed in alphabetical order.
3. Press : to browse the phonebook.
To view the details of a phonebook entry, press mVIEW.
To dial a number from the phonebook, scroll : to the phonebook entry and press r.
TIP Instead of scrolling : to browse the phonebook entries, you can press the numeric key
corresponding to the first letter of the entry you wish to locate. For example, pressing 2 will show
the entries starting with A. Pressing 2 again will show the entries starting with B, etc...
Store a contact in the phonebook
1. Press mMENU, scroll : to Phonebook and press mSELECT, press mSELECT to enter New
Entry.
2. Enter the name of the contact (maximum 12 characters) and press mOK.
3. Enter the number (maximum 24 digits) and press mOK.
4. Enter the SMS Box number and press mOK (only for UK).
21
Phonebook
EN
5. Scroll : to choose a group (<No Group>, <Group A>, <Group B>, <Group C>) and press
mSELECT to confirm.
A long confirmation beep tone is emitted.
You can assign individual contacts to specific groups of your choice. For example, Group A contains
phone numbers of all your co-workers. You can also assign a specific ring melody to that group (see
"Group Melody" on page 36) . If you have subscribed to Caller Line Identification service from your
network provider, every time someone from that group calls you, you will hear the designated
ringtone for that group.
TIP You can store up to 250 phonebook entries. You cannot store a new phonebook entry when
the memory is full. In this case, you have to delete existing entries to make space for new entries.
Edit a phonebook entry
1. Press mMENU, scroll : to Phonebook and press mSELECT, scroll : to Edit Entry and press
mSELECT.
2. Scroll : to the entry you wish to edit and press mSELECT.
3. Press >CLEAR to erase the letters one by one, edit the name and press mOK.
4. Press >CLEAR to erase the digits one by one, edit the number and press mOK.
5. Enter the SMS Box number and press mOK (only for UK).
6. Scroll : to a group (<No Group>, <Group A>, <Group B>, <Group C>) and press mOK to
confirm.
A long confirmation beep tone is emitted.
Delete a phonebook entry
1. Press mMENU, scroll : to Phonebook and press mSELECT, scroll : to Delete Entry and press
mSELECT.
2. Scroll to the entry you wish to delete and press mSELECT.
A long confirmation beep tone is emitted.
Delete all phonebook entries
1. Press mMENU, scroll : to Phonebook and press mSELECT, scroll : to Delete All and press
mSELECT.
2. Press mSELECT again to confirm.
A long confirmation beep tone is emitted.
22
Phonebook
EN
Store direct access memory
You can store up to 9 direct access memories (Key 1 to 9). A long press on the keys in stand-by
mode will automatically dial the stored phone number.
1. Press mMENU, scroll : to Phonebook and press mSELECT, scroll : to Direct Memory and
press mSELECT.
2. Select a key (Key 1 to Key 9) and press mVIEW. If there is a stored number in that key, the number/
name will be displayed.
3. If there is no number stored for the selected key or if you want to change the number currently stored,
press mSELECT and press mSELECT again to select Add.
4. Press mOK to display the phonebook list and scroll : to the entry you wish to store as direct access
memory.
5. Press mOK to confirm.
A long confirmation beep tone is emitted.
Delete a direct access memory
1. Press mMENU, scroll : to Phonebook and press mSELECT, scroll : to Direct Memory and
press mSELECT.
2. Select a key (Key 1 to Key 9) and press mVIEW.
3. Press mMENU and scroll : to Delete.
4. Press mOK to confirm.
A long confirmation beep tone is emitted.
Copy phonebook from SIM card
This feature allows you to copy the SIM card phonebook of your mobile phone to the phonebook of your
handset.
1. Open the SIM card tray and remove it from the base station.
Remove SIM
card tray
23
Phonebook
EN
2. Slide the SIM card between the retaining clips, microchip facing up, until it stops.
3. Put the SIM card tray back in the slot on the base station and push into place until it latches.
4. On the handset, press mMENU, scroll : to Phonebook and press mSELECT, scroll : to Copy
from SIM and press mSELECT.
5. Scroll : to Copy All or Select Entry. If you choose Copy All then all entries in the SIM card will be cop-
ied to your phonebook. If you choose Select Entry, you can browse the SIM card entries and select the
ones you wish to copy.
6. Press mSELECT to confirm.
7. Enter the PIN code of the SIM card (if required). The copy progress will be displayed on the screen.
8. A message Transferred! will be displayed upon successful completion.
Your handset should be able to read all standard SIM phonebook contents. If the handset is unable to
read the SIM card, or no SIM card is detected, the screen will display an error message No SIM Card!
and return to previous menu.
TIP You can select >CANCEL anytime to abort the process.
Transfer phonebook
This feature allows you to transfer the phonebook from one handset to another handset when there are at
least 2 handsets registered to your base station.
1. Press mMENU, scroll : to Phonebook and press mSELECT, scroll : to Phbk transfer and press
mSELECT.
2. The handset numbers which are available for transfer will be displayed. If there are more than 2 handsets,
you can scroll : to select a specific handset.
3. Press mSELECT to confirm.
4. The called handset will be prompted with a message Transfer from Handset X.
5. To accept the transfer of phonebook, press mSELECT on the called handset; to reject the transfer,
press > CANCEL.
6. A message Transferred! will be displayed upon successful completion.
24
Call log
EN
The call log can store up to 50 entries. If you have subscribed to Caller Line Identification (CLI), and provided
the identity of the caller is not withheld, the name (or number) of the caller will be displayed together with the
date & time of the call (if provided by the network). The calls (missed and received) are displayed in
chronological order with the most recent call at the top of the list. When the call log is empty, the screen
displays List Empty.
Access call log
1. Press u in stand-by mode, press mSELECTtto enter Call Log and scroll : to view the entries.
Save call log entry to phonebook
1. Press u in stand-by mode, press mSELECTtto enter Call Log and scroll : to select an entry.
2. Press mSELECT and press mSELECT again to Copy to Phbk.
3. Enter name and press mOK.
4. Edit number if necessary and press mOK.
5. Enter the SMS Box number and press mOK (only for UK).
6. Scroll : to choose a group (<No Group>, <Group A>, <Group B>, <Group C>) and press
mSELECT to confirm.
A long confirmation beep tone is emitted.
Delete call log entry
1. Press u in stand-by mode, press mSELECTtto enter Call Log and scroll : to select an entry.
2. Press mSELECT and scroll : to Delete.
3. Press mSELECT to confirm.
A long confirmation beep tone is emitted.
Delete all call log
1. Press u in stand-by mode, press mSELECTtto enter Call Log.
2. Press mSELECT and scroll : to Delete All and press mSELECT.
3. Press mSELECT again to confirm.
A long confirmation beep tone is emitted.
Access redial list
1. Press > in stand-by mode and scroll : to view the entries.
25
Call log
EN
View details of a redial list entry
1. Press > in stand-by mode and scroll : to select an entry.
2. Press mSELECT and press mSELECT again to View.
Save redial list entry to phonebook
1. Press > in stand-by mode and scroll : to select an entry.
2. Press mSELECT, scroll : to Copy to Phbk and press mSELECT.
3. Enter name and press mOK.
4. Edit number if necessary and press mOK.
5. Enter the SMS Box number and press mOK (only for UK).
6. Scroll : to choose a group (<No Group>, <Group A>, <Group B>, <Group C>) and press
mSELECT to confirm.
A long confirmation beep tone is emitted.
Delete a number from redial list
1. Press > in stand-by mode and scroll : to select an entry.
2. Press mSELECT and scroll : to Delete and press mSELECT.
A long confirmation beep tone is emitted.
Delete all redial list
1. Press > in stand-by mode.
2. Press mSELECT and scroll : to Delete All and press mSELECT.
3. Press mSELECT again to confirm.
A long confirmation beep tone is emitted.
26
SMS
EN
SMS
Write a SMS
Inbox
Draft box
SMS Settings
SMS stands for Short Message Service. To benefit from this service, you must subscribe to Caller Line
Identification Service (CLI) together with SMS service from your network provider. SMS messages can be
exchanged with a phone (mobile or compatible fixed lines), provided the receiver has also subscribed to CLI
and SMS services.
The factory settings on your SE630 correspond to the main national operator. If you wish to send or receive
SMS messages through another service provider, you must set the corresponding numbers (see page 32).
You can create up to 10 SMS boxes (Box 0 to Box 9) and protect each box with a password (only for UK).
Your SE630 can store up to 50 SMS messages (40 SMS in the Inbox and 10 SMS in the Draft box) shared by
all the SMS boxes and the maximum length of each message is 160 characters.
In order to send and receive SMS messages, there must be at least one SMS Box. Box 9 with empty password
is created by default (only for UK). For more information, please refer to "SMS Box (only for UK)" on page 31.
Write and send new SMS
1. Press mMENU, press mSELECT to enter SMS, press mSELECT again to enter Write a SMS.
2. Scroll
:
to the desired SMS Box (Box 0 to Box 9) and press mSELECT to enter password (only for UK).
3. Enter the password (if needed) and press mOK.
Key
Operation
Press to move cursor left by 1 position.
u
Press and hold to jump to the 1st character/digit.
Press to move cursor right by 1 position.
Press and hold to jump to the last character/digit.
Press to erase the previous character/digit.
Press to return to the previous menu if there are no characters/digits on the input screen.
Long press to delete all characters/digits.
d
>CLEAR
4. Enter the text and press mOK.
You can enter up to 160 characters for an SMS.
If you receive a call while writing an SMS, the operation will be interrupted. However, your SMS will
be saved in the Draft box. To retrieve it, go to Draft box in your SMS menu (see page 30).
27
SMS
EN
5. Enter the destination phone number and press mOK. Or press mPHBK to browse the phonebook
list to select a phone number, press mSELECT and press mOK.
6. Enter the destination box number (0 to 9) directly and press mOK (only for UK).
By default, the destination box is 9 (the default destination box depends on the country).
7. Press mSELECT to Send the message or scroll : to Save as Draft to save the message in the Draft
box and press mSELECT to confirm.
8. If you select Send, the message will be sent immediately. SMS Sent! will be displayed if the message has
been sent successfully.
If the message cannot be sent successfully, the screen will display SMS not Sent! and the message will
be saved in the Draft box.
WARNING When composing your SMS, if no keys are pressed for 60 seconds, the handset will
return to stand-by mode. The edited message will be automatically saved in the Draft box.
Inbox
The messages in the Inbox are listed according to the time of receipt, with the newest message appearing first.
The Inbox can store up to 40 messages (shared between Box 0 to Box 9).
Each time an SMS is received, you will be alerted by a beep tone (see "SMS Tone" on page 36) and the screen
displays the number of new messages received. If LED is activated, the event LED will blink until the SMS has
been reviewed.
WARNING When the message box is full, you will not be able to receive new messages. In this case,
you need to delete some old messages in order to receive new ones
View Inbox messages
1. Press mMENU, press mSELECT to enter SMS, scroll : to Inbox press mSELECT.
2. Scroll : to your desired box number and press mSELECT (only for UK).
3. Enter the password and press mOK (Password is not required for Box 9).
4. Browse the list of SMS messages and select the message you wish to read. The message list will be
displayed with the sender’s phone number or corresponding name (if the number matches the
phonebook record).
5. Press mVIEW to view the message content.
TIP While reading an SMS, press : to scroll to the next or previous row. At the end of the
message, the sender’s phone number and the date and time of reception are shown.
28
SMS
EN
6. When viewing the message content, you can press mMENU to access the following options:
Reply
Send a reply to the sender of the message.
Forward the message to another recipient.
Save the sender’s number to your phonebook.
Delete the selected message.
Edit
Copy to Phbk
Delete
Delete All
Delete all messages in the Inbox.
7. To return to SMS menu, press e.
Press r while viewing the message content/sender number/date/time stamp will abort the SMS
function and dial the sender’s phone number.
Press e to return to Inbox message list.
Reply to an Inbox message
2. Scroll : to Reply and press mSELECT to start editing.
3. After editing, press mOK to confirm the message.
4. Refer to steps 5 to 7 in "Write and send new SMS" on page 27 to send the message or select Save as
Draft to save the message in the Draft box.
Forward an Inbox message
1. While viewing the message content, press mMENU to display the Inbox menu options.
2. Scroll : to Edit and press mSELECT to start editing it if you wish.
3. After editing, press mOK to confirm message.
4. Refer to steps 5 to 7 in "Write and send new SMS" on page 27 to forward the message or select Save To
Draft to save the message in the Draft box.
Save sender’s phone number to phonebook
1. While viewing the message content, press mMENU to display the Inbox menu options.
2. Scroll : to Copy to Phbk and press mSELECT to enter a name for this new contact.
3. Enter the name and press mOK to modify number.
4. To confirm the number, press mOK again.
5. Enter the SMS Box number and press mOK (only for UK).
6. Scroll : to select a group you wish to assign for this contact and press mSELECT to confirm.
A long confirmation beep is emitted and the screen returns to display the message content.
Delete an Inbox message
1. While viewing the message content, press mMENU to display the Inbox menu options.
2. Scroll : to Delete and press mSELECT to confirm deletion.
29
SMS
EN
Delete all Inbox messages
1. While viewing the message content, press mMENU to display the Inbox menu options.
2. Scroll : to Delete All and press mSELECT.
3. Press mSELECT again to confirm deletion.
Draft box
In addition to SMS messages saved as drafts, all the SMS messages that are not successfully sent will be
automatically stored in the Draft box. The Draft box can store up to 10 messages.
Review Draft messages
1. Press mMENU, press mSELECT to enter SMS, scroll : to Draft box and press mSELECT.
2. Scroll : to your desired box number and press mSELECT (only for UK).
3. Enter the password and press mOK (Password is not required for Box 9).
4. Browse the list of SMS messages and select the message you wish to review.
5. Press mVIEW to view the message content.
6. When viewing the message content, you can press mMENU to access the following options:
Send
Send the message immediately.
Edit the message and send or save as draft.
Delete the message.
Edit
Delete
Delete All
Delete all messages in the Draft box.
Send a message from Draft box
2. Press mSELECT to Send the message.
3. Press mSELECT again to confirm or scroll : to Save as Draft to save the message in the Draft box
and press mSELECT.
4. If you select Send, the message will be sent immediately. SMS Sent! will be displayed if the message has
been sent successfully.
Edit a Draft message
1. While viewing the message content, press mMENU to display the Draft box menu options.
2. Scroll : to Edit and press mSELECT to start editing.
3. After editing, press mOK to confirm message.
4. Refer to steps 5 to 7 in "Write and send new SMS" on page 27 to send the message or select Save as
Draft to save the message in the Draft box.
Delete a Draft message
1. While viewing the message content, press mMENU to display the Draft box menu options.
30
SMS
EN
2. Scroll : to Delete and press mSELECT to confirm deletion.
Delete all Draft messages
1. While viewing the message content, press mMENU to display the Draft box menu options.
2. Scroll : to Delete All and press mSELECT.
3. Press mSELECT again to confirm deletion.
SMS settings
This menu allows you to set up the server for sending and receiving SMS messages. Your SE630 can receive
messages from 3 service centers.
Each service center consists of 2 numbers:
- Incoming number
- Outgoing number
The maximum length of an incoming/outgoing number is 24 digits.
The incoming and outgoing numbers of your SE630 are already set to work on your country network. We
advise you not to modify these settings. For more details or in case of any problems, please contact your local
network provider.
SMS reception
Your SE630 can receive SMS messages from another phone if you have subscribed to the CLI and SMS ser-
vices from your network provider. By default, SMS reception is set to On so that you can receive SMS mes-
sages.
To activate or deactivate the reception of SMS
1. Press mMENU, press mSELECT to enter SMS, scroll : to SMS Settings and press mSELECT,
press mSELECT to enter SMS Reception.
2. Scroll : to On or Off and press mSELECT to confirm.
Even if SMS reception is Off, you can still send SMS messages.
SMS Box (only for UK)
In order to send and receive SMS messages, there must at least be 1 SMS Box created. Box 9 with empty
password is created by default.
You can create a maximum of 10 SMS boxes (Box 0 to Box 9), and you can protect each box with a
password.
To create a new SMS Box (only for UK)
1. Press mMENU, press mSELECT to enter SMS, scroll : to SMS Settings and press mSELECT,
scroll : to SMS Boxes and press mSELECT.
2. Press mMENU and press mSELECT to Add New Box.
31
SMS
EN
3. Enter box name (maximum 12 characters) and press mOK.
4. Enter a password (maximum 8 digits) and press mOK.
5. Enter the password again and press mOK.
You can choose to leave the password empty. If no password is required, simply press mOK
when prompted to enter password.
6. Enter the SMS box number and press mOK.
If the confirmation password is correct, the new SMS box will be created. A long confirmation beep is
emitted and the screen returns to SMS box list.
To change the password of an SMS Box (only for UK)
1. Press mMENU, press mSELECT to enter SMS, scroll : to SMS Settings and press mSELECT,
scroll : to SMS Boxes and press mSELECT.
2. Scroll : to the SMS box for which you wish to change password and press mSELECT.
3. Scroll : to Change Passwd and press mSELECT.
4. Enter old password and press mOK.
5. Enter new password, press mOK and enter the new password again for confirmation.
6. Press mOK to confirm password change.
To delete an SMS Box (only for UK)
1. Press mMENU, press mSELECT to enter SMS, scroll : to SMS Settings and press mSELECT,
scroll : to SMS Boxes and press mSELECT.
2. Scroll : to the SMS box you wish to delete and press mMENU.
3. Scroll : to Delete Box and press mSELECT.
4. Enter password (if needed) and press mOK to confirm box deletion.
To change the box number of an SMS Box (only for UK)
1. Press mMENU, press mSELECT to enter SMS, scroll : to SMS Settings and press mSELECT,
scroll : to SMS Boxes and press mSELECT.
2. Scroll : to the SMS box you for which wish to change the box number and press mMENU.
3. Scroll : to Change Box Nr and press mSELECT.
4. Enter the new box number and press mOK to confirm box number change.
To set outgoing number
The incoming and outgoing numbers of your SE630 are already set to work on your country network.
We advise you not to modify these settings. For more details or in case of any problems, please contact your
local network provider.
1. Press mMENU, press mSELECT to enter SMS, scroll : to SMS Settings and press mSELECT,
scroll : to SMS Center 1, SMS Center 2 or SMS Center 3 and press mSELECT.
2. Press mSELECT to enter Outgoing Nr..
32
SMS
EN
3. Enter the number and press mOK to confirm.
A confirmation beep is emitted.
The maximum length of an outgoing number is 24 digits.
To set incoming number
1. Press mMENU, press mSELECT to enter SMS, scroll : to SMS Settings and press mSELECT,
scroll : to SMS Center 1, SMS Center 2 or SMS Center 3 and press mSELECT.
2. Scroll : to Incoming Nr. and press mSELECT.
3. Enter the number and press mOK to confirm.
A confirmation beep is emitted.
The maximum length of an incoming number is 24 digits.
Default SMS center
The default SMS center number is 1.
To set default SMS center
1. Press mMENU, press mSELECT to enter SMS, scroll : to SMS Settings and press mSELECT,
scroll : to Default Ctr. and press mSELECT.
2. Scroll : to SMS center that you wish to set as default center (SMS Center 1, SMS Center 2 or SMS
Center 3) and press mSELECT.
A confirmation beep is emitted.
1st ring
When this function is set to Off, the first ring from a voice call will not sound. This is particularly useful in coun-
tries where calling line identity is sent after the first ring, so no phones in the house would ring when a message
arrives.
To set 1st ring
1. Press mMENU, press mSELECT to enter SMS, scroll : to SMS Settings and press mSELECT,
scroll : to Set 1st Ring and press mSELECT.
2. Scroll : to On or Off and press mSELECT to confirm.
33
Clock & Alarm
EN
Clock & Alarm
Set Date/Time
Alarm
Alarm Tone
Set date and time
1. Press mMENU, scroll : to Clock & Alarm and press mSELECT, press mSELECT again to enter
Set Date/Time.
2. Enter the current time (HH:MM) and current date (DD/MM/YY) and press mSELECT.
Enter the date in Day/Month/Year format and the time in 24-hour format.
3. A confirmation beep is emitted and the screen returns to Clock & Alarm menu.
Once the date and time are set, there will be time & date recovery when the batteries are removed,
or when there is a power failure.
Set Alarm
1. Press mMENU, scroll : to Clock & Alarm and press mSELECT, scroll : to Alarm and press
mSELECT.
2. Scroll : to Off, On Once or On Daily and press mSELECT.
3. If you have selected On Once or On Daily, enter the time for the alarm and press mSELECT.
A confirmation beep is emitted and the screen returns to previous menu.
The alarm tone and alarm icon will only sound/blink for 1 minute when the alarm time is reached. To
mute the alarm tone, simply press any key on the handset.
Alarm tone
1. Press mMENU, scroll : to Clock & Alarm and press mSELECT, scroll : to Alarm Tone and
press mSELECT.
2. Scroll : to the desired melody (Melody 1, Melody 2 or Melody 3) to play the melody.
3. Press mSELECT to set the alarm tone.
34
Personal Settings
EN
Personal Set
Handset Tones
Wallpaper
Contrast
Screensaver
Handset Name
Auto Pick-up
Auto Hang-up
Language
Babysit Mode
Handset Tones
Ring Volume
There are 5 ringer volume options (Silence, Low, Medium, High and Progressive). The default level is Medium.
To set ring volume
1. Press mMENU, scroll : to Personal Set and press mSELECT, press mSELECT to enter
Handset Tones and press mSELECT again to enter Ring Volume.
2. Scroll : to your desired volume level and press mSELECT to confirm.
A confirmation beep is emitted and the screen returns to previous menu.
When Silence is activated, the icon
is displayed on the screen.
WARNING When the handset rings during an incoming call, please do not hold the handset too
close to your ear as the volume of the ringing tone may damage your hearing.
Ring Melody
There are 10 ring melodies available on your handset.
To set Ring Melody
1. Press mMENU, scroll : to Personal Set and press mSELECT, press mSELECT to enter
Handset Tones, scroll : to Ring Melody and press mSELECT.
2. Scroll : to your desired melody to play the melody.
35
Personal Settings
EN
3. Press mSELECT to set the ring melody.
A confirmation beep is emitted and the screen returns to previous menu.
Group Melody
To benefit from this feature, you must subscribe to the Caller Line ldentification service. See "Caller Line
Identification" on page 20.
This menu enables you to select and set the melodies to be played when there is an external incoming call
from a contact whose name is stored in your phonebook and is part of a group. You can associate 1 ring
melody to each group.
There are three phonebook groups (Group A, B, C) available for you to organize your contacts. Each group
can be assigned a unique melody.
To set Group Melody
1. Press mMENU, scroll : to Personal Set and press mSELECT, press mSELECT to enter
Handset Tones, scroll : to Group Melody and press mSELECT.
2. Scroll : to the group for which you wish to set melody and press mSELECT.
3. Scroll : to the desired melody to play the melody.
4. Press mSELECT to set the group melody.
A confirmation beep is emitted and the screen returns to previous menu.
Key Beep
A single beep is emitted when a key is pressed. You can enable or disable this key beep. By default, the key
beep is On.
To set key beep On/Off
1. Press mMENU, scroll : to Personal Set and press mSELECT, press mSELECT to enter
Handset Tones, scroll : to Key Beep and press mSELECT.
2. Scroll : to On or Off and press mSELECT to confirm.
A confirmation beep is emitted and the screen returns to previous menu.
SMS Tone
A tone is emitted when a new SMS is received. You can enable or disable this SMS Tone. By default, SMS tone
is On.
To set SMS tone On/Off
1. Press mMENU, scroll : to Personal Set and press mSELECT, press mSELECT to enter
Handset Tones, scroll : to SMS Tone and press mSELECT.
2. Scroll : to On or Off and press mSELECT to confirm.
A confirmation beep is emitted and the screen returns to previous menu.
36
Personal Settings
EN
Wallpaper
This feature allows you to select the wallpaper to be displayed in stand-by mode. There are 4 wallpapers
pre-installed on your phone. Please see "Default settings" on page 16 for the default wallpaper.
To set wallpaper
1. Press mMENU, scroll : to Personal Set and press mSELECT, scroll : to Wallpaper and press
mSELECT.
2. Scroll : to your desired wallpaper and press mSELECT to confirm.
A confirmation beep is emitted and the screen returns to previous menu.
Contrast level
There are 3 contrast level options (Level 1, Level 2 or Level 3). The default contrast level is Level 2.
To set contrast level
1. Press mMENU, scroll : to Personal Set and press mSELECT, scroll : to Contrast and press
mSELECT.
2. Scroll : to your desired contrast level (Level 1, Level 2 or Level 3) and press mSELECT to confirm.
A confirmation beep is emitted and the screen returns to previous menu.
Screensaver
Screensaver will be activated automatically after 1 minute in stand-by mode.
To set screensaver
1. Press mMENU, scroll : to Personal Set and press mSELECT, scroll : to Screensaver and press
mSELECT.
2. Scroll : to On or Off and press mOK to confirm.
A confirmation beep is emitted and the screen returns to previous menu.
Handset Name
You can name the handset and display the handset name in stand-by mode. The default handset name of your
handset is PHILIPS.
To rename the handset
1. Press mMENU, scroll : to Personal Set and press mSELECT, scroll : to Handset Name and
press mSELECT.
37
Personal Settings
EN
2. Edit the handset name and press mOK to confirm.
A confirmation beep is emitted and the screen returns to previous menu.
Maximum length of the handset name is 12 characters and the default handset name is PHILIPS.
Auto Pick-up
This function enables you to answer a call automatically by simply lifting the handset from the base station. By
default, the Auto Pick-up feature is Off.
To set Auto Pick-up mode
1. Press mMENU, scroll : to Personal Set and press mSELECT, scroll : to Auto Pick-up and press
mSELECT.
2. Scroll : to On or Off and press mSELECT to confirm.
A confirmation beep is emitted and the screen returns to previous menu.
Auto Hang-up
This function enables you to end a call automatically by simply replacing the handset on the base station.
By default, the Auto Hang-up feature is On.
To set Auto Hang-up mode
1. Press mMENU, scroll : to Personal Set and press mSELECT, scroll : to Auto Hang-up and
press mSELECT.
2. Scroll : to On or Off and press mSELECT to confirm.
A confirmation beep is emitted and the screen returns to previous menu.
Language
Your SE630 can support different display languages.
To change the language
1. Press mMENU, scroll : to Personal Set and press mSELECT, scroll : to Language and press
mSELECT.
2. Scroll : to your desired language and press mSELECT to confirm.
A confirmation beep is emitted and the screen returns to previous menu.
38
Personal Settings
EN
Babysit mode
You must have at least 2 handsets registered to your base station to be able to use this feature (see page 43
"To register an additional handset").
This feature allows you to monitor, e.g. the baby’s room. Place the handset in the room to be monitored. If the
sound level around the microphone of the handset exceeds a certain threshold, the handset can automatically
call another handset registered on the same base station.
To use the Babysit feature you need to activate it (e.g. on handset 1) and enter the number of the handset to
be called (e.g. handset 2) in the event that there are noises in the monitored room. Place the handset which is
in Babysit mode (e.g. handset 1) in the room to be monitored. If this handset detects a sound level greater than
a certain threshold, it will automatically initiate an internal call to the selected handset (e.g. handset 2).
To activate Babysit mode
1. Press mMENU, scroll : to Personal Set and press mSELECT, scroll : to Babysit mode and press
mSELECT.
2. Enter the number of the handset you wish to call to and press mOK to activate.
In Babysit mode, all keys are deactivated except for m key. Babysit mode is displayed on the
screen when this function is activated and the handset cannot make or receive calls.
To deactivate Babysit mode
1. Press m, select Off and press mOK.
39
Advanced Settings
EN
Advanced Set
Recall Time
Dial Mode
Call Barring
Baby call
Registration
Select Base
Unregistration
Change PIN
Reset
Auto prefix
Country
Conference
Recall Time
Recall time (or dial delay) is the time delay by which the line will be disconnected after you press r key.
It can be set to short, medium or long.
The default value of recall time that is preset in your SE630 should be the best suited for your country network
and therefore you should not need to change it.
To set recall time
1. Press mMENU, scroll : to Advanced Set and press mSELECT and press mSELECT to enter
Recall Time.
2. Scroll to select Short / Medium / Long and press mSELECT to confirm.
A confirmation beep is emitted and the screen returns to previous menu.
This setting is useful when using network services. The use of some services accessed with [r +
1] , [r + 2 ] , [r + 3] (call waiting, call forward...) will depend on your recall time
setting. Please contact your network provider for more details on this feature.
40
Advanced Settings
EN
Dial Mode
The default value for dial mode that is preset in your SE630 should be the best suited for your country
network and therefore you should not need to change it.
There are 2 dial modes: Tone or Pulse.
To set dial mode
1. Press mMENU, scroll : to Advanced Set and press mSELECT, scroll : to Dial Mode and press
mSELECT.
2. Scroll : to Tone or Pulse and press mSELECT to confirm.
A confirmation beep is emitted and the screen returns to previous menu.
Call Barring
Call barring enables you to restrict selected handsets from dialling a phone number beginning with certain
numbers. You can set up to four different barring numbers, with each number containing up to 4 digits.
If you have modified the Master PIN before and it is not the default 0000, you will be required to
enter the Master PIN before you can activate or deactivate call barring mode, add or modify call
barring number.
To activate/deactivate Call Barring mode
1. Press mMENU, scroll : to Advanced Set and press mSELECT, scroll : to Call Barring and press
mSELECT.
2. Enter the Master PIN when prompted and press mOK to confirm.
3. Press mSELECT to enter Barring Mode.
4. Scroll : to On or Off and press mSELECT to confirm.
A confirmation tone is emitted and the screen returns to previous menu.
To modify Call Barring number
1. Press mMENU, scroll : to Advanced Set and press mSELECT, scroll : to Call Barring and press
mSELECT.
2. Enter the Master PIN when prompted and press mOK to confirm.
3. Scroll : to Barring Number and press mSELECT.
4. Scroll : to Number 1, Number 2, Number 3 or Number 4 and press mSELECT to confirm.
5. Enter a maximum of 4 digits and press mOK to confirm.
A confirmation beep is emitted and the screen returns to stand-by mode.
If a restricted number is dialled, the call will not be connected. When this happens, the phone emits
an error tone and returns to stand-by mode.
41
Advanced Settings
EN
Baby Call
When activated, the Baby Call feature enables you to dial a number by pressing any key on your handset. This
feature is very useful for direct access to emergency services.
You can enter up to 24 digits for baby call number.
If you have modified the Master PIN before and it is not the default 0000, you will be required to
enter the Master PIN before you can activate or deactivate Baby Call mode or change Baby Call
number.
To activate Baby Call mode
1. Press mMENU, scroll : to Advanced Set and press mSELECT, scroll : to Baby call and press
mSELECT.
2. Enter the Master PIN when prompted and press mOK to confirm.
3. Press mSELECT to enter Mode.
4. Scroll : to On and press mOK to confirm.
When Mode is activated but the Baby Call number is not set yet, your handset will prompt you to
enter a number.
5. Enter the Baby Call number and press mOK to confirm.
A confirmation message will be displayed on the screen.
To deactivate Baby Call mode
1. Long press mMENU (when Baby Call mode has been activated before).
2. Scroll : to Off and press mSELECT to confirm.
To change Baby Call number
1. Press mMENU, scroll : to Advanced Set and press mSELECT, scroll : to Baby call and press
mSELECT.
2. Enter the Master PIN when prompted and press mOK to confirm.
3. Scroll : to Number and press mSELECT.
4. The last stored Baby Call number is displayed (if any).
5. Enter the new Baby Call number and press mOK to confirm.
A long confirmation beep is emitted and the screen returns to previous menu.
42
Advanced Settings
EN
Registration
The procedures described below are the procedures that you will find in your SE630 handset. The procedures
may vary according to the handset you want to register. In this case, please refer to the manufacturer of the
additional handset.
Additional handsets must be registered to the base unit before you can use them. Up to 5 handsets can be
registered to one base station.
The Master PIN is required before you can register or unregister handsets. The default PIN is 0000.
To register an additional handset
1. On the base station, press and hold c for 3 seconds in stand-by mode. After that, the registration
procedure has to be done within 1 minute.
Within 1 minute, the base station is able to accept registration from a handset. If no key is pressed
within 10 seconds, the registration procedure will be aborted.
2. At the same time, on the handset, press mMENU, scroll : to Advanced Set and press mSELECT,
scroll : to Registration and press mSELECT.
3. Enter the Master PIN when prompted and press mOK to start registration.
4. Press : to select the Base to be registered to and press mOK to confirm.
If the base is found and the PIN is correct, the unused handset numbers will be displayed and you can
select a handset number by entering the number directly.
If the PIN is incorrect, Incorrect PIN will be displayed and the handset returns to stand-by mode.
A long confirmation tone is emitted to indicate successful registration and the screen returns to stand-by
mode.
Select Base
One SE630 handset can register up to 4 different SE630 Base stations. By default, the handset will register to
BASE 1. If you select Any Base, the handset will register to the nearest base station.
To manually select a base station
1. Press mMENU, scroll : to Advanced Set press mSELECT, scroll : to Select Base and press
mSELECT.
2. Scroll : to the desired base station and press mOK to confirm.
3. The handset will start searching for the base station. If the selected base is found, a long confirmation tone
is emitted.
43
Advanced Settings
EN
Unregistration
To unregister a handset
1. Press mMENU, scroll : to Advanced Set and press mSELECT, scroll : to Unregistration and
press mSELECT.
2. Enter the Master PIN when prompted and press mOK to confirm.
3. Press on the handset keypad the handset number corresponding to the handset that you wish to
unregister.
If there are no key presses within 15 seconds, the unregistration procedure will be aborted and the
handset returns to stand-by mode.
A long confirmation beep is emitted to indicate successful unregistration and the screen shows
Unregistered.
Change Master PIN
The Master PIN is used for setting call barring/baby call number and for registration/unregistration of handsets.
The default Master PIN number is 0000. The length of the PIN is 4 digits. This PIN is also used to protect the
settings of your handset. Your handset will prompt you whenever the PIN is required.
To change Master PIN
1. Press mMENU, scroll : to Advanced Set and press mSELECT, scroll : to Change PIN and press
mSELECT.
2. Enter the current Master PIN when prompted and press mOK to confirm. The PIN entered will be
shown as asterisks (*) on the screen.
If an incorrect PIN is entered, Incorrect Pin will be displayed and the screen returns to stand-by
mode.
If your PIN number is the default 0000, step 2 is skipped.
3. Enter new PIN and press mOK.
4. Enter new PIN again and press mOK to confirm PIN change.
A confirmation tone is emitted, the message New PIN Stored appears and the screen returns to
previous menu.
If the Master PIN is modified, you will be required to enter the Master PIN before you can modify
Call Barring and Baby Call settings.
44
Advanced Settings
EN
Reset
Reset to default settings
1. Press mMENU, scroll : to Advanced Set and press mSELECT, scroll : to Reset and press
mSELECT.
2. Enter the Master PIN when prompted and press mOK.
If your PIN number is the default 0000, step 2 is skipped.
3. Scroll : to Yes and press mSELECT.
A confirmation beep is emitted, and the unit is reset to its default settings (please see "Default settings" on
page 16).
The WELCOME mode will appear again after master reset.
Auto Prefix
The maximum length of an auto prefix number is 5 digits. Once the number is set, it will be automatically
inserted at the beginning of each number that will be dialled.
To set auto prefix number
1. Press mMENU, scroll : to Advanced Set and press mSELECT, scroll : to Auto prefix and press
mSELECT.
2. The last stored auto prefix number is displayed (if any).
3. Enter the number and press mSELECT to confirm.
A confirmation beep is emitted and the screen returns to previous menu.
Country Setting
The availability of this menu is dependent on your country.
You can select another country different from the one chosen during Welcome mode.
1. Press mMENU, scroll : to Advanced Set and press mSELECT, scroll : to Country and press
mSELECT.
2. Enter the Master PIN when prompted and press mOK to confirm.
You need to enter the Master PIN even if your PIN is 0000 (default PIN).
45
Advanced Settings
EN
3. Scroll : to the country of your choice and press mSELECT to confirm.
Once the country is selected, the default line settings for the selected country will be applied to the
phone automatically (e.g. Recall time, Dial mode, Language, etc).
Conference Mode
When Conference mode is activated, you can initiate a three-party conference call with a second handset
registered to your base station automatically if the second handset takes the line when there is already an
external call in progress.
The default setting for this mode is Off.
To activate/deactivate conference mode
1. Press mMENU, scroll : to Advanced Set and press mSELECT, scroll : to Conference and press
mSELECT.
2. Scroll : to On or Off and press mSELECT to confirm.
A confirmation beep is emitted and the screen returns to previous menu.
46
Network Services
EN
Net. Service
Call Forward
Call Fwd Busy
Call Fwd UnAns
Voice Mail
Call Back
Cancel Call Bk
Withhold ID
This menu provides a convenient means for you to access, activate or deactivate some network services that
are country/subscription dependent. Contact your network provider for more information about these
services.
The default numbers and values that are preset in your SE630 should be the best suited for your country
network and therefore you should not need to change them.
Call Forward
There are 3 call forwarding options available: Unconditional Call Forwarding, When Busy and When Unanswered.
Set up Call Forward number
1. Press mMENU, scroll : to Net. Service and press mSELECT.
2. Scroll : to the type of call forwarding option you wish to set (Call Forward / Call Fwd Busy / Call Fwd
UnAns) and press mSELECT.
3. Scroll : to Settings and press mSELECT to enter the number for forwarding.
4. Press mOK to confirm.
Activate Call Forward
1. Press mMENU, scroll : to Net. Service and press mSELECT.
2. Scroll to the type of call forwarding option you wish to set (Call Forward / Call Fwd Busy / Call Fwd
UnAns) and press mSELECT.
3. Press mSELECT to Activate.
4. The number string for that selected service will be dialled.
5. When the number has been dialled, press e to return to stand-by mode.
When this feature is activated, depending on the call forwarding option you have set, your incoming
calls will be forwarded to the number of your choice.
Deactivate Call Forward
1. Press mMENU, scroll : to Net. Service and press mSELECT.
47
Network Services
EN
2. Scroll : to the type of call forwarding option you wish to set (Call Forward / Call Fwd Busy / Call Fwd
UnAns) and press mSELECT.
3. Scroll : to Deactivate and press mSELECT to confirm.
4. The number string for that selected service will be dialled.
5. When the number has been dialled, press e to return to stand-by mode.
Voice Mail
This feature allows the caller to leave a voice message when you are unable, or do not wish to take a call
yourself. The availability of this feature is dependent on your country and your subscription with your network
provider. Charges often apply for you to retrieve messages, as these are stored by the network rather than on
the handset itself. Contact your network provider for more information about this feature.
Set up Voice Mail number
1. Press mMENU, scroll : to Net. Service and press mSELECT, scroll : to Voice Mail and press
mSELECT.
2. Scroll : to Voice Mail 1 or Voice Mail 2 and press mSELECT.
3. Scroll : to Settings and press mSELECT.
4. Modify the voice mail number and press mOK.
Activate Voice Mail
1. Press mMENU, scroll : to Net. Service and press mSELECT, scroll : to Voice Mail and press
mSELECT.
2. Scroll : to Voice Mail 1 or Voice Mail 2 and press mSELECT.
3. Press mSELECT to Activate.
4. The number string for that selected service will be dialled.
5. When the number has been dialled, press e to return to stand-by mode.
Call Back
Setting
1. Press mMENU, scroll : to Net. Service and press mSELECT, scroll : to Call Back and press
mSELECT.
2. Scroll : to Settings and press mSELECT.
3. Enter the required number for call back and press mOK.
Activate Call Back
1. Press mMENU, scroll : to Net. Service and press mSELECT, scroll : to Call Back and press
mSELECT.
2. Press mSELECT to Activate.
3. The number string for that selected service will be dialled.
48
Network Services
EN
4. When the number has been dialled, press e to return to stand-by mode.
Cancel Call Back
Setting
1. Press mMENU, scroll : to Net. Service and press mSELECT, scroll : to Cancel Call Bk and
press mSELECT.
2. Scroll : to Settings and press mSELECT.
3. Enter the required number for cancelling of call back and press mOK.
Activate Cancel Call Back
1. Press mMENU, scroll : to Net. Service and press mSELECT, scroll : to Cancel Call Bk and
press mSELECT.
2. Press mSELECT to Activate.
3. The number string for that selected service will be dialled.
4. When the number has been dialled, press e to return to stand-by mode.
Withhold ID
Setting
1. Press mMENU, scroll : to Net. Service and press mSELECT, scroll : to Withhold ID and press
mSELECT.
2. Scroll : to Settings and press mSELECT.
3. Enter the required number for withholding ID and press mOK.
Activate Withhold ID
1. Press mMENU, scroll : to Net. Service and press mSELECT, scroll : to Withhold ID and press
mSELECT.
2. Press mSELECT to Activate.
3. The number string for that selected service will be dialled.
4. When the number has been dialled, press e to return to stand-by mode.
Deactivate Withhold ID
1. Press mMENU, scroll : to Net. Service and press mSELECT, scroll : to Withhold ID and press
mSELECT.
2. Scroll : to Deactivate and press mSELECT to confirm.
3. The number string for that selected service will be dialled.
4. When the number has been dialled, press e to return to stand-by mode.
49
Games
EN
Games
Memory
Tetris
Memory
The objective of this game is to find and match different pairs of graphics in the shortest possible time using
your memory. To win, you have to complete matching all 8 pairs of graphics in a 4x4 matrix.
To start the game
1. Press mMENU, scroll : to Games and press mSELECT, press mSELECT to enter Memory
game.
2. An instruction screen is displayed.
Press 2 / 4 / 6 / 8 keys to move up / down / left / right respectively.
Press 5 to select.
3. Press mSELECT or press 5 to start the game.
4. To exit from the game, press >.
Tetris
You can rotate each shaped block as they fall such that they fit neatly into horizontal blocks. The more blocks
you can gather within the same level, the more you will score.
To start the game
1. Press mMENU, scroll : to Games and press mSELECT, scroll : to Tetris and press
mSELECT.
2. An instruction screen is displayed.
Press 2 / 4 / 6 / 8 keys to rotate / move left / move right / move down respectively.
3. Press mSELECT to start the game.
4. To exit from the game, press >.
50
Troubleshooting
EN
Troubleshooting of the phone
Problem
Causes
Solution
The
icon is not blinking
• Bad battery contact
• Dirty contact
• Move the handset slightly
when the handset is placed
on the base
• Clean the battery contact with a
cloth moistened with alcohol
• Battery is full
• No power
• No need to charge
No dialling tone
• Check the connections. Reset
the phone: unplug and plug
back in the mains
• Batteries are empty
• Charge the batteries for at least
24 hours
• You are too far from the base
station
• Move closer to the base station
• Wrong line cable
• Use the line cable provided
• Line adaptor (when needed) is
not connected to the line cord
• Connect the line adaptor (when
needed) to the line cord
Poor audio quality
• You are too far from the base
station
• Move closer to the base station
• The base station is too close to
electrical appliances, reinforced
concrete walls or metal
doorframes
• Move the base station at least
one metre away from any elec-
trical appliances
The
icon is blinking
• Handset is not registered to
the base station
• Register the handset to the base
station
• The handset is too far from the
base station
• Move closer to the base station
The copy from my mobile
phone SIM card to SE630
phonebook is not complete.
Only phonebook entries from
your mobile phone SIM card will
be transferred; the phonebook
entries that are stored on your
mobile phone memory will not be
transferred.
Transfer the phonebook entries
that are on your mobile phone
memory to your mobile phone
SIM card and then to your SE630.
51
Troubleshooting
EN
Problem
Causes
Solution
The handset displays “not
available”
• The procedure to add
handset has failed
a
• Try again by disconnecting and
connecting the base station
power supply and follow the
procedure to register a handset
(see page 43)
• Remove and place back the
handset batteries
• when attempting to add
another handset to the
base station
• Maximum number of handsets
(5) has been reached
• Unregister a handset so as to
register the new handset
• Base station is already busy
with another handset
• when using a handset
• Wait until it is available
Noise interference on your
radio or television
power pack are too close to
electrical appliances
station as far away as possible
Caller Line Identification (CLI)
service does not work
The service is not activated
Check your subscription with your
network operator
No ring tone
The ring tone is deactivated
The phonebook is full
Increase the volume
A phonebook entry cannot
be stored
Delete an entry to free memory
Cannot receive new SMS
• SMS storage space is full
• Wrong SMS settings
• Delete old SMS
• Check your SMS settings (see
page 31)
Cannot send or receive new
SMS
• The outgoing or incoming SMS
center numbers are not set or
are wrong
• Refer to "SMS settings" on page
31
• You have no subscription
• Contact your provider for more
information
• Another SMS-enabled phone is
also on your line
• Deactivate the SMS reception
mode on one of the device
• There is a problem of compati- • Contact your provider for more
bility between operators
• The identity is withheld
information
• Show identity (see "Withhold
ID" on page 49)
52
Information
EN
Electric, Magnetic and Electromagnetic
Fields ("EMF")
1. Philips Royal Electronics manufactures and sells many consumer oriented products which usually, as with
any electronic apparatus, have the ability to emit and receive electro magnetic signals.
2. One of Philips' leading Business Principles is to take all necessary health and safety precautions for our
products, to comply with all applicable legal requirements and to stay well within the EMF standards
applicable at the time of producing the products.
3. Philips is committed to develop, produce and market products that cause no adverse health effects.
4. Philips confirms that if its products are handled properly for their intended use, they are safe to use
according to scientific evidence available today.
5. Philips plays an active role in the development of international EMF and safety standards, enabling Philips
to anticipate further developments in standardisation for early integration in its products.
Conformity
Hereby, Philips Consumer Electronics, BLC P&ACC, declares that the SE630x is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.
Recycling and disposal
Disposal instructions for old products
The WEEE Directive (Waste Electrical and Electronic Equipment: 2002/96/EC) has been put in place to ensure
that products are recycled using best available treatment, recovery and recycling techniques to ensure human
health and give utmost protection to the environment.
Your product is designed and manufactured with high quality materials and components, which can be recycled
and reused.
Do not dispose of your old product in your general household waste bin. Inform yourself about the local
separate collection system for electrical and electronic products marked by this symbol:
Use one of the following disposal options:
1. Dispose of the complete product (including its cables, plugs and accessories) in the
designated WEEE collection facilities
2. If you purchase a replacement product, return your old product, in its entirety, to the
retailer. He should accept it as required by the WEEE Directive.
Philips has marked the packaging with standard symbols designed to promote the
recycling and appropriate disposal of your eventual waste.
A financial contribution has been paid to the associated national recovery &
recycling system.
The labelled packaging material is recyclable.
53
Index
EN
A
G
S
Accessories 5
Group melody 36
H
SMS 27
Alarm 34
SMS Boxes 31
Alarm tone 34
Answer a call 14, 18
Auto Hang-up 38
Auto Pick-up 38
Auto Prefix 45
SMS Tone 36
Handset Name 37
SMS reception 31
SMS settings 31
Save redial list 26
Screensaver 37
Select Base 43
Handset Tones 35
Handsfree answering 18
I
Icons & symbols 8
Inbox 28
Incoming number 33
Install battery 12, 13, 14, 16
Intercom 19
Intrusion Mode 46
K
Key Beep 36
Keypad lock 14
Keypad lock/unlock 14
Keypad unlock 14
B
Send SMS 27
Baby Call 42
Stand-by mode 14
Store a contact 21
Switch handset on/off 14
Babysit mode 39
Backlight 15
Basic operations 11
Battery level 13
T
Tetris 50
C
Text and number entry 16
Transfer an external call 19
Transfer phonebook 24
Call 41
Call Back 48
Call Barring 41
U
Call Forward 47
Call log 17, 25
L
Unmute 18
Unregister 44
V
Voice Mail 48
W
Wallpaper 37
Withhold ID 49
Write a SMS 27
Call waiting 20
Language 38
Loudspeaker 18
Loudspeaker mode 18
Loudspeaker volume 19
Caller Line Identification 20
Calls in-progress 18
Charge battery 12
Clock & Alarm 34
Conference call 20
Conformity 53
M
Make a call 14
Master PIN 44
Memory 50
Menu navigation 10
Mute 18
Mute handset 18
Connect Base Station 11
Contrast 37
Copy phonebook from SIM
card 23
Country Setting 46
D
Date & time 34
Date and time 14
Default SMS center 33
Default settings 16
Delete SMS message 29
Delete call log 25
Delete phonebook 22
Dial Mode 40
Direct access memory 23
Direct dialling 17
Draft box 30
N
Noise interference 52
O
Other network services 49
Out of range 13
Outgoing number 32
Overview of the base station 9
Overview of the handset 6
P
Paging 14
Personalize 35
Phonebook 17, 21
Predialling 17
E
Earpiece volume 18
Edit Draft message 30
Edit phonebook 22
End a call 14, 18
R
Recall Time 40
Recycling and disposal 53
Redial list 17, 25
Registration 43
Event LED 15
F
Reply SMS message 29
Reset Unit 45
Ring Melody 35
Ring Volume 35
Forward SMS message 29
54
3PECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICEꢀ
4RADEMARKS ARE THE PROPERTY OF +ONINKLIJKE 0HILIPS %LECTRONICS .ꢀ6ꢀ OR THEIR RESPECTIVE OWNERSꢀ
ꢁꢂꢂꢃ ¥ +ONINKLIJKE 0HILIPS %LECTRONICS .ꢀ6ꢀ !LL RIGHTS RESERVEDꢀ
WWWꢀPHILIPSꢀCOM
ꢄꢅꢅꢅ ꢁꢆꢇ ꢁ6593
|