Philips Flat Panel Television PSS 2000BR SS User Manual
I N S T R U C T I O N  
M A N U A L  
Plasma Swivel Stand  
(PSS-2000BR/SS)  
The Plasma Swivel Stand (PSS-2000) is available in black  
(PSS-2000BR) or silver (PSS-2000SS) to securely mount  
your large flat panel display. A stylish solution for residential,  
commercial and business applications, the PSS-200 pro-  
vides a wide variety of features for most table top installa-  
tions.  
Features include +/-45 degrees of swivel, free standing with  
bolt down capability for permanent installation or security,  
infinite height adjustment of 5” and two cable options for  
ease of installation. The PSS-2000 swivel feature offers  
optional stops at +/-15 degrees, 25 degrees or 35 degrees.  
The infinite height adjustment of 5” allows for different screen  
heights up to 32 inches and cables may extend from the back  
of the display or be routed through an access hole in the mid-  
dle of the stand.  
The PSS-2000 uses Chief’s exclusive Q-Latch™ Mounting  
System for easy installation, stable mounting and quick  
release. A video conferencing shelf, aesthetic cover kit, and  
Q-clamps for added security are available.  
BEFORE YOU BEGIN  
• CAUTION: To prevent damage to the stand, which could affect or void the Factory warranty, thoroughly  
study all instructions and illustrations before you begin to install or operate the unit. Pay particular atten-  
tion to the “Important Precautions” on Page 1.  
• The maximum weight to be installed on the PSS is 150 pounds (68.36 Kg)  
• If you have any questions about this assembly, contact Chief Manufacturing at 1-800-582-6480 or 952-582-6480.  
PART NO. 8800-000039 (Rev. D)  
CHIEF MANUFACTURING INC.  
1-800-582-6480 952-894-6280 FAX 952-894-6918  
8401 EAGLE CREEK PARKWAY, STE. 700  
SAVAGE, MINNESOTA 55378 USA  
©2004 Chief Manufacturing  
www.chiefmfg.com  
09-05  
 
Instruction Manual  
Swivel Stand  
IMPORTANT WARNINGS and CAUTIONS!  
WARNING:  
CAUTION:  
A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.  
A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corre-  
sponding instructions.  
•
WARNING:Improper installation can result in serious personal injury! Make sure that the structural members can  
support a redundant weight factor five times the total weight of the equipment: if not, reinforce the struc-  
ture before installing the table stand.  
•
•
•
WARNING:Be aware also of the potential for personal injury or damage to the unit if it is not adequately mounted.  
CAUTION: Inspect the unit for shipping damage.  
CAUTION: Do not use cleanser or harsh cleaning agents on displays.  
TOOLS REQUIRED FOR INSTALLATION  
• Phillips screwdriver  
NOTE: Other tools may be required depending on the  
method of installation.  
CONTENTS  
INSPECT PARTS BEFORE ASSEMBLY ......... 2  
DISPLAY PREPARATION PROCEDURES ..... 3  
STAND ASSEMBLY PROCEDURES ............... 3  
DISPLAY INSTALLATION PROCEDURES ... 5  
STAND ADJUSTMENT PROCEDURES .......... 5  
STAND ANCHORING PROCEDURES ............ 6  
CABLE MANAGEMENT .................................. 6  
1
 
Instruction Manual  
Swivel Stand  
INSPECT PARTS BEFORE ASSEMBLY  
Remove and Inspect the Stand  
1. Open shipping container, remove unit from container, and  
remove wooden shipping base.  
2. Carefully inspect the stand for shipping damage. If any  
damage is apparent, call your carrier claims agent and do  
not continue with the assembly procedure until the carrier  
has reviewed the damage.  
NOTE: Read all assembly instructions before start-  
ing assembly.  
3. Carefully inspect all components for damage (See  
able 1 and Figure 1).  
Table 1:  
Item #  
Description  
Quantity  
10  
20  
30  
40  
50  
Stand Assembly  
Bumper, rubber  
1
5
1
1
1
Wrench, Allen, 3/16”  
Wrench, Allen, 5/32”  
Template, paper (Not Shown)  
10  
20  
30  
40  
Figure 1. Parts  
2
 
Instruction Manual  
Swivel Stand  
DISPLAY PREPARATION PROCEDURES  
Prepare the display for installation as follows:  
1. Install the PSB bracket (shipped with the PSS) on your  
display according to the instructions included in PSB  
bracket package.  
STAND ASSEMBLY PROCEDURES  
Attach rubber bumpers here  
Free Standing (not anchored) Applications Only:  
NOTE: Do not perform this step if you are going to anchor  
the stand to a surface.  
1. Install five rubber bumpers on the bottom of the stand  
(see Figure 1).  
Display Measuring 30 Inches or Smaller In Height:  
NOTE: Stand comes assembled for displays 30” in height or  
less and lowered to its minimum height for shipment.  
1. Loosen the four height adjustment screws and raise the  
slide to its maximum height (see Figure 2).  
Figure 1. Free Standing Installations Only  
2. Secure the slide in place by tightening the four height  
adjustment screws.  
Display Measuring More Than 30 Inches In Height:  
1. Remove the slide from the base by removing four height  
adjustment screws (see Figure 3).  
Adjust height using these screws  
2. Remove the front plate from the slide by removing two  
nuts securing the front plate (see Figure 3).  
3. Install the front plate in the upper mounting holes of slide  
and secure using the two nuts removed in the previous  
step (see Figure 4).  
4. Install the slide on the base using the four height adjust-  
ment screws (see Figure 3).  
5. Raise the slide to its maximum height (see Figure 2).  
6. Secure the slide in place by tightening the four height  
adjustment screws.  
Figure 2. Height Adjustment  
3
 
Instruction Manual  
Swivel Stand  
Slide  
Height Adj.  
Screws  
Front Plate  
Nuts  
Figure 3. Stand Assembly  
Reattach front plate using these holes  
Flag in down  
(lowered)  
position  
Nuts  
Holes used for displays measuring  
less than 30 Inches Tall  
Figure 4. For displays Taller Than 30 Inches  
4
 
Instruction Manual  
Swivel Stand  
DISPLAY INSTALLATION PROCEDURES  
Install the display as follows:  
1. Make sure the latching flag of the stand is in the open  
(lowered) position (see Figure 4).  
2. Align the mounting buttons of the PSB bracket, installed  
on your display, with the teardrop slots in the mounting  
plate of the stand.  
3. Lower the display into place and raise the latching flag to  
secure the display. If the latching flag will not engage  
completely, the display is not properly mounted. Make  
sure the mounting buttons rest at the bottom of the tear-  
drop slots.  
Adjust swivel tension using these screws  
STAND ADJUSTMENT PROCEDURES  
Adjust display height as follows:  
CAUTION: Displays are fragile. Allowing the display to drop to  
the bottom of stand travel may result in damage to the display.  
1. While holding the display in place, loosen the four height  
adjustment screws (see Figure 2).  
Figure 5. Tension Adjustment Screws  
2. Position the display to the desired height.  
3. Tighten the four height adjustment screws (see Figure 2).  
Adjust stand tension as follows:  
Select swivel stop by inserting  
10-24 X 1/2” Phillips head screw  
in one of these holes  
1. With the display secured to the stand assembly, check  
swivel tension.  
2. If tension adjustment is necessary, slightly tighten or  
loosen adjustment screws on stand assembly (see Fig-  
ure 5).  
3. Repeat Step 1 and Step 2 as necessary.  
Adjust stand swivel stop as follows:  
1. If desired, insert the 10-24 X 1/2” Phillips head cap screw  
in one of the three swivel stop holes (15, 25 or 35  
degrees) in the base of the stand (see Figure 6).  
Figure 6. Swivel Stops (15, 25 or 35 Degrees)  
5
 
 
Instruction Manual  
Swivel Stand  
STAND ANCHORING PROCEDURES  
1/4-20 X 1/2” Tapped holes  
NOTE: Due to the wide variety of anchoring options, hard-  
ware is not provided.  
Anchor stand follows:  
1. Select a suitable location for anchoring, allowing for room  
for swivel and access for cabling.  
2. Using the template provided, drill anchoring holes for the  
four 1/4-20 X 1/2” tapped holes (see Figure 7).  
3. If routing cables through mounting surface, Use the tem-  
plate provided and drill the cable access hole in the  
mounting surface.  
Figure 7. Anchoring Hole Locations  
CABLE MANAGEMENT  
Install cables as follows:  
1. Attach cabling to flat panel display.  
2. Route cables in one of three ways:  
a. down the back of the display (open),  
b. through the center post of the stand and out the bot-  
tom of the stand in the back,  
c. through the center post of the stand and through a  
hole in the mounting surface.  
6
 
 

Peavey Microphone PVM 535N User Manual
Pelco Security Camera C1640M B User Manual
Philips Cell Phone 21A582BH User Manual
Philips Computer Monitor 105G78 User Manual
Philips Headphones SHB4000 User Manual
Philips Portable Radio AE6580 00 User Manual
Philips Stereo System MCM5 User Manual
Pioneer Car Stereo System SX 3400 User Manual
Pioneer DVD Recorder DVR 310 User Manual
Prince Castle Toaster TX 208 User Manual