Portable CD Player
AX7101
AX7104
AX7113
Audio
Read this manual first!
Return
If you have any problems, do not attempt
to return this product to the store.
yourWarranty
Registration Card
within 10 days
For fast help, call us first!
1-800-531-0039
Y
PHILIPS CONSUMER ELECTRONICS COMPANY
A Division of Philips Electronics North America Corporation
Knoxville, Tennessee 37914-1810, U.S.A.
English
Français
Español
Meet Philips at the Internet
CLASS 1
LASER PRODUCT
AX7101
AX7104
AX7113
3140 115 2891.1
Printed in China
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
9. Only use attachments/accessories specified by the manufacturer.
10.
Use only with a cart, stand, tripod, bracket, or table specified
by the manufacturer or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
11. Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as if the power-supply cord
or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, or when the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
12. Battery usage CAUTION – To prevent battery leakage which may result in bodily
injury or damage to the unit:
7. Do not block any of the ventilation openings. Install in accordance
with the manufacturers instructions.
➟ Install all batteries correctly, + and - as marked on the unit.
➟ Do not mix batteries (old and new or carbon and alkaline, etc.).
➟ Remove batteries when the unit is not used for a long time.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
EL 6474-E002: 01/3
Return your W arranty Registration card today to
ensure you receive all the benefits you’re entitled to.
• Once your Philips purchase is
registered, you’re eligible to receive all
the privileges of owning a Philips
product.
• So complete and return the Warranty
Registration Card enclosed with your
purchase at once.And take advantage
of these important benefits.
W arranty
O wner
Model
Verification
Confirm ation Registration
Registering your product
within 10 days confirms
your right to maximum
protection under the
terms and conditions of
your Philips warranty.
Your completed Warranty Returning your Warranty
Registration Card serves
as verification of
Registration Card right
away guarantees you’ll
ownership in the event of receive all the information
product theft or loss.
and special offers which
you qualify for as the
owner of your model.
Know these
For Custom er Use
Enter below the Serial No. which is
located on the bottom of the cabinet.
Retain this information for future reference.
safety
C AUTION
symbols
RIS K OF ELECTRIC S HOCK
DO NOT OP EN
Model No. _______________________
Serial No. ________________________
CAUTION: TO REDUCE THE RIS K OF ELECTRIC S HOCK, DO NOT
REM OVE COVER (OR BACK). NO US ER-S ERVICEABLE P ARTS
INS IDE. REFER S ERVICING TO QUALIFIED S ERVICE P ERS ONNEL.
This “bolt of lightning”
indicates uninsulated
material within your unit
WARNING: TO PREVENT
FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS EQUIPMENT TO
RAIN OR MOISTURE.
may cause an electrical shock. For the
safety of everyone in your household,
please do not remove product
covering.
CAUTIO N: To prevent electric
shock, match wide blade of plug to
wide slot, and fully insert.
The “exclamation point” calls
attention to features for
which you should read the
enclosed literature closely to prevent
operating and maintenance problems.
MAC5097
LIMITED WARRANTY
PO RTABLE CO MPACT DISC
One Year Free Exchange
This product must be carried in for an exchange.
W HO IS COVERED?
You must have proof of purchase to exchange the product.A sales receipt or other
document showing that you purchased the product is considered proof of purchase.
Attach it to this owner’s manual and keep both nearby.
W HAT IS COVERED?
Warranty coverage begins the day you buy your product. For one year thereafter, a
defective or inoperative product will be replaced with a new, renewed or comparable
product at no charge to you.A replacement product is covered only for the original
warranty period.When the warranty on the original product expires, the warranty on
the replacement product also expires.
W HAT IS EXCLUDED?
Your warranty does not cover:
•
labor charges for installation or setup of the product, adjustment of customer controls
on the product, and installation or repair of antenna systems outside of the product.
product repair and/or part replacement because of misuse, accident, unauthorized
repair or other cause not within the control of Philips Consumer Electronics
Company.
•
•
•
reception problems caused by signal conditions or cable or antenna systems outside
the unit.
a product that requires modification or adaptation to enable it to operate in any
country other than the country for which it was designed, manufactured, approved
and/or authorized, or repair of products damaged by these modifications.
incidental or consequential damages resulting from the product. (Some states do not
allow the exclusion of incidental or consequential damages, so the above exclusion may
not apply to you.This includes, but is not limited to, prerecorded material, whether
copyrighted or not copyrighted.)
•
•
a product that is used for commercial or institutional purposes.
W HERE IS EXCHANGE AVAILABLE?
You may exchange the product in all countries where the product is officially distributed
by Philips Consumer Electronics Company. In countries where Philips Consumer
Electronics Company does not distribute the product, the local Philips service
organization will attempt to provide a replacement product (although there may be a
delay if the appropriate product is not readily available).
BEFO RE REQ UESTING EXCHANGE...
Please check your owner’s manual before requesting an exchange.Adjustments of the
controls discussed there may save you a trip.
Philips Service Solutions Group, P.O. Box 2976,
Longview,Texas 75606, (903) 242-4800
EXCHANGING A PRO DUCT IN U.S.A.,
PUERTO RICO O R U.S.VIRGIN ISLANDS...
Contact your dealer to arrange an exchange. Or, ship the product, insured and freight
prepaid, and with proof of purchase enclosed, to the address listed below.
Small Product Service Center
Philips Service Company
907 Snapps Ferry Road, Plant 2, Building 6
Greeneville,TN 37743
(In U.S.A., Puerto Rico and U.S.Virgin Islands, all implied warranties, including implied
warranties of merchantability and fitness for a particular purpose, are limited in duration
to the duration of this express warranty. But, because some states do not allow limitations
on how long an implied warranty may last, this limitation may not apply to you.)
EXCHANGING A PRO DUCT IN CANADA...
Please contact Philips at:
1-800-661-6162 (French Speaking)
1-800-363-7278 (English Speaking)
(In Canada, this warranty is given in lieu of all other warranties. No other warranties are
expressed or implied, including any implied warranties of merchantability or fitness for a
particular purpose. Philips is not liable under any circumstances for any direct, indirect,
special, incidental or consequential damages, howsoever incurred, even if notified of the
possibility of such damages.)
TO GET O UT-O F-WARRANTY EXCHANGE...
In U.S.A., Puerto Rico or U.S.Virgin Islands, contact Philips Service Company at (800)
vince
531-0039 to obtain the cost of out-of-warranty exchange.Then carefully pack the
product and ship it to the Small Product Service Center (address listed above). In
Canada, call the phone number listed above under “Exchanging a Product in Canada” to
obtain the cost of out-of-warranty exchange.
REMEMBER...
Please record the model and serial numbers found on the product below.Also, please fill
out and mail your warranty registration card promptly. It will be easier for us to notify
you if necessary.
MODEL #
SERIAL #
____________________________________
____________________________________
This warranty gives you specific legal rights.You may have other rights
which vary from state/province to state/pro
.
EL4967E005 / MAC 4110 / 1-97
POWER SUPPLY / GENERAL INFORMATION
Mains adapter (supplied or optionally available)
English
CONTROLS / POWER SUPPLY
CONTROLS ( see figure
1
)
Use only the AY 3170 adapter (4.5 V / 300 mA direct
current, positive pole to the center pin). Any other
product may damage the player.
1 OPEN 2 ..............opens the CD lid
2 2; ......................switches the player on, starts or pauses CD play
3 9.........................stops CD play, clears a program or switches the player off
4 § .......................skips and searches CD tracks forwards
.5
V
DC
1
Make sure the local voltage corresponds to the power
adapter’s voltage.
5 ESP......................EXTREME SHOCK PROTECTION ensures continuous CD
2
Connect the power adapter to the 4.5V DC jack of the
player and to the wall outlet.
playback regardless of vibrations and shocks
6 MODE .................selects the different playing possibilities: SHUFFLE,
SHUFFLE REPEAT ALL, REPEAT, REPEAT ALL and SCAN
Note: Always disconnect the adapter when you are not using it.
7 ............................display
8 PROGRAM ..........programs tracks and reviews the program
9 BASS...................switches the bass enhancement on and off. This button also
switches acoustic feedback (the beep) on/off when it is
pressed for more than 2 seconds
Environmental information
•
•
All redundant packing material has been omitted. We have done our utmost to
make the packaging easily separable into two materials: cardboard (box) and
polyethylene (bags, protective foam sheet).
0 ∞ .......................skips and searches CD tracks backwards
! RESUME .............stores the last position of a CD track played
HOLD...................locks all buttons
OFF......................switches RESUME and HOLD off
@ LINE OUT/p........3.5 mm headphone jack and LINE OUT jack to connect the
player to another audio input of an additional appliance,
remote control jack (not on all versions)
Your set consists of materials which can be recycled if disassembled by a
specialized company. Please observe the local regulations regarding the
disposal of packing materials, dead batteries and old equipment.
# VOL E ............adjusts the volume
$ 4.5V DC...............jack for external power supply
% ............................belt clip holder
^ ............................type plate
Batteries (supplied or optionally available)
CD player and CD handling
•
•
Do not touch the lens A of the CD player.
You can use the following batteries with this CD-player:
Do not expose the unit, batteries or CDs to humidity,
rain, sand or excessive heat (caused by heating
equipment or direct sunlight).
•
•
normal batteries type LR6, UM3 or AA (preferably Philips), or
alkaline batteries type LR6, UM3 or AA (preferably Philips).
•
•
You can clean the CD player with a soft, slightly
dampened, lint-free cloth. Do not use any cleaning
agents as they may have a corrosive effect.
To clean the CD, wipe it in a straight line from the
center toward the edge using a soft, lint-free cloth. A
cleaning agent may damage the disc! Never write on a CD or attach a sticker
to it.
The lens may cloud over when the unit is moved suddenly from cold to warm
surroundings. Playing a CD is not possible then. Leave the CD player in a warm
environment until the moisture has evaporated.
Active mobile phones in the vicinity of the CD player may cause malfunctions.
Avoid dropping the unit as this may cause damage.
Notes:– Old and new or different types of batteries should not be combined.
– Remove batteries if they are empty or if the player is not going to be used for
a long time.
Inserting batteries
1
2
Push OPEN 2 to open the CD lid.
•
Open the battery compartment and insert either 2
normal or alkaline batteries.
•
•
Battery indication
The approximate power level of your batteries is shown in the display.
Headphones HL351
Battery full
•
Connect the supplied headphones to the LINE OUT/p
jack of the player.
Battery two-thirds full
Battery one-third full
Note: LINE OUT/p can also be used for connecting the
player to your HiFi system (with a signal lead) or to
your car radio (with a cassette adapter or signal
lead). In both cases, the volume of the player must
be set to position 8.
Battery dead or empty. When the batteries are
dead or empty, the symbol A flashes,
bAttis displayed, and the beep tone sounds repeatedly.
Average playing time of batteries under normal conditions
IMPORTANT!
Battery type
Normal
Alkaline
ESP on
5 hours
22 hours
Power Save
6 hours
Hearing safety: Do not play your headphones at a high volume. Hearing experts
advise that continuous use at high volume can permanently damage your hearing.
Traffic safety: Do not use headphones while driving a vehicle. It may create a
hazard and it is illegal in many countries. Even if your headphones are an open-air
type designed to let you hear outside sounds, do not turn up the volume so high
that you cannot hear what is going on around you.
25 hours
Batteries contain chemical substances, so they should be disposed
of properly.
GENERAL INFORMATION / CD PLAY
CD PLAY / FEATURES
In-car use (connections supplied or optionally available)
Playback information
•
•
If a CD-Recordable (CD-R) or a CD-Rewritable (CD-RW) is not recorded
properly, nF dISCis displayed, indicating that the CD has not been
finalized. In that case, use FINALIZE on your CD recorder to complete the
recording.
Only use the AY 3545 (4822 219 10033) or AY 3548 (3140 118 71890) car voltage
converter (4.5 V DC, positive pole to the center pin) and the AY 3501 cassette car
adapter. Any other product may damage the set.
1
Put the set on a horizontal, vibration-free and
stable surface. Make sure it is in a safe place,
where the set is neither a danger nor an
obstacle to the driver and the passengers.
When playing a CD-Rewritable (CD-RW), please note that it takes 3–15
seconds after pressing 2; for sound reproduction to start.
12 V DC
•
•
Playback will stop if you open the CD lid.
While the CD is read, 1-:-flashes in the display.
2
Plug the voltage converter into the
cigarette lighter jack (only for 12 V car
battery, negative grounding), then connect
the wired end with 4.5V DC input jack on the
set.
4,5 V DC
Volume and bass
O
F
F
•
R
E
S
U
M
E
•
H
O
L
D
E
N
P
O
L
I
N
E
O
U
T/
VO
L.
Volume adjustment
Adjust the volume by using VOL E.
•
3
4
If necessary, clean the cigarette lighter jack to
obtain a good electrical contact.
Bass adjustment
Turn down the volume and connect the cassette adapter plug to LINE OUT/p
on the set.
E
D
O
•
Press BASS to switch the bass enhancement on or
off
M
P
S
E
5
6
7
Carefully insert the cassette adapter into the car radio’s cassette compartment.
Make sure the cord does not hinder your driving.
y
is shown if the bass enhancement is acti-
M
A
vated.
S
S
A
B
Set VOL E on the set to position 8. Start playback on the set and adjust
the sound with the car radio controls.
Remote control (supplied or optionally available)
•
Always remove the voltage converter from the cigarette lighter jack-
when the set is not in use.
Use the AY 3767 or AY 3768 cord remote control.The buttons on the remote
control have the same functions as the corresponding buttons on the set.
Note: If your car radio has a LINE IN jack, it is better to use it for the
car radio connection instead of the cassette.adapter. Connect the signal
lead to this LINE IN jack and to LINE OUT/p on the set.
1
2
3
Press 9 twice to switch off the set.
Firmly connect the remote control to LINE OUT/p on the set.
Adjust the volume VOL E on the CD player and remote control.
Playing a CD
Selecting a track and searching
This CD-player can play all kinds of Audio Discs such
Selecting a track during playback
P
S
E
as CD-Recordables and CD-Rewritables. Do not try to
T
OS
BO
SS
BA
C
MI
NA
DY
L
•
Briefly press ∞ or § once or several times to skip to
the current, previous or next track.
yPlayback continues with the selected track, and
the track’s number is displayed.
TA
GI
DI
play a CD-ROM, CDi, VCD, DVD or computer CD.
O
L
D
N
E
P
O
L
I
N
E
O
U
T
/
1
2
Push the OPEN 2 slider to open the player.
VOL.
Selecting a track when playback is stopped
Insert an audio CD, printed side up, by pressing the
CD onto the hub.
1
Briefly press ∞ or § once or several times to select the desired track. The
track number is displayed.
E
D
O
M
P
S
E
3
4
Close the player by pressing the lid down.
2
Press 2; to start CD play.
yPlayback starts with the selected track.
Press 2; to switch the player on and start playback.
yThe current track number and elapsed playing
time are displayed.
S
S
Searching for a passage during playback
1
Keep ∞ or § pressed to find a particular passage in
a backward or forward direction.
ySearching starts while playback continues at low
volume. After 2 seconds the search speeds up.
•
You can pause playback by pressing 2;.
yThe time at which playback was paused starts
flashing.
•
You can continue playback by pressing 2; again.
2
Release the button when you reach the desired passage.
yPlayback continues from this position.
5
Press 9 to stop playback.
yThe total number of tracks and the total playing
time of the CD are displayed.
Notes: – If the player is in SCAN mode (see MODE chapter), searching is not
possible.
– In SHUFFLE, SHUFFLE REPEAT ALL or REPEAT mode (see MODE
chapter), or while playing a program, searching is only possible within
the particular track.
6
Press 9 again to switch the player off.
•
To remove the CD, hold it by its edge and press the
hub gently while lifting the CD.
Note: If there is no activity, the set will automatically
switch off after a while to save energy.
FEATURES
FEATURES / TROUBLESHOOTING
RESUME and HOLD
Programming track numbers
You can interrupt playback and continue (even after an
extended period of time) from the position where
playback stopped (RESUME) and you can lock all buttons
of the set so that no action will be executed (HOLD).
Use the RESUME–HOLD–OFF slider for these functions.
You can store up to 30 tracks to play in a program.
A single track may be stored more than once in the
program.
S
E
M
A
R
G
O
R
P
S
S
A
B
1
While playback is stopped, select a track with
∞ or §.
RESUME – continuing from where you have stopped
2
Press PROGRAM to store the track.
yPROGRAM lights up; the track number
programmed and Pwith the total number of
stored tracks are displayed.
1
Switch the slider to RESUME during playback to activate RESUME.
yRESUME is shown.
2
3
Press 9 whenever you want to stop playback.
Press 2; whenever you want to resume playback.
yRESUME is shown and playback continues from
where you have stopped.
3
4
Select and store all desired tracks in this way.
Press 2; to start playback of your selected tracks.
yPROGRAM is shown and playback starts.
•
To deactivate RESUME, switch the slider to OFF.
yRESUME goes off.
•
You can review the program by pressing PROGRAM
for more than 2 seconds.
yThe display shows all the stored tracks in
sequence.
HOLD – locking all buttons
You can lock the buttons of the set by switching the slider to HOLD. Now, when a
key is pressed, no action will be executed. This is of use, for example, when
transporting the player in a bag. With HOLD activated, you can avoid accidental
activation of other functions.
Notes: – If you press PROGRAM and there is no track selected, SELis
displayed.
– If you try to store more than 30 tracks, FULLis displayed.
1
Switch the slider to HOLD to activate HOLD.
yAll buttons are locked. HoLdis shown when
you press any button. If the set is switched off,
HoLdwill be shown only when 2; is
pressed.
Clearing the program
•
While playback is stopped, press 9 to clear program.
yCLris displayed once, PROGRAM goes off, and
the program is cleared.
2
To deactivate HOLD, switch the slider to OFF.
Note: The program will also be cleared if the power
supply is interrupted, or if the CD-player lid is opened, or if the set
switches off automatically.
Note: If you deactivate HOLD by switching the slider to RESUME, you will be
activating the RESUME function.
Selecting different playing possibilities−MODE
Troubleshooting
It is possible to play tracks in random order, to repeat a
WARNING: Under no circumstances should you try to repair the set yourself as
this will invalidate the warranty. If a fault occurs, first check the points listed,
before taking the unit for repair. If you are unable to solve a problem by following
these hints, consult your dealer or service center.
E
D
single track or the entire CD, and to play the first few
O
M
seconds of each track.
P
S
E
1
Press MODE during playback as often as required in
order to activate one of the following ‘modes’. The
active mode is shown in the display.
S
The CD player has no power, or playback does not start
ySHUFFLE : All tracks of the CD are played in
•
Check that your batteries are not dead or empty, that they are inserted
correctly, that the contact pins are clean.
random order until all of them have been played once.
ySHUFFLE REPEAT ALL : All tracks of the CD are
•
•
Your adapter connection may be loose. Connect it securely.
For in-car use, check that the car ignition is on. Also check player’s batteries.
played repeatedly in random order.
yREPEAT : The current track is played repeatedly.
The indication no diSCis displayed
yREPEAT ALL : The entire CD is played repeatedly.
•
•
Check that the CD is clean and correctly inserted (label-side upward).
If your lens has steamed up, wait a few minutes for this to clear.
ySCAN: The first 10 seconds of each of the
remaining tracks are played in sequence.
The indication nF diSCis displayed
CD-RW (CD-R) was not recorded properly. Use FINALIZE on your CD-recorder.
2
Playback starts in the chosen mode after 2 seconds.
•
•
To return to normal playback, press MODE repeatedly until the display shows
no active modes.
The indication HOLD is on and/or there is no reaction to controls
•
•
If HOLD is activated, then deactivate it.
Electrostatic discharge. Disconnect power or remove batteries for a few seconds.
ESP / Power Save Mode
With a conventional portable CD-player you might have experienced that the
The CD skips tracks
music stopped e.g. when you were jogging. The EXTREME SHOCK PROTECTION
•
•
The CD is damaged or dirty. Replace or clean the CD.
RESUME, SHUFFLE or PROGRAM is active. Switch off whichever is on.
prevents loss of sound caused by light vibrations and shocks. Continuous playback
is ensured. However ESP does not prevent playback interruptions during vigorous
running. It also does not protect the unit against any damage caused by dropping!
In this set ESP is default ON. It is possible to set ESP off. and enter the Power
Save Mode.(PS). PS helps to extend battery lifetime for longer playback.
No sound or bad sound quality.
•
•
•
•
PAUSE might be active. Press 2;.
•
Press ESP once.
Loose, wrong or dirty connections. Check and clean connections.
Volume might not be appropriately adjusted. Adjust the volume.
Strong magnetic fields. Check player’s position and connections. Also keep
away from active mobile phones.
yESP disappears.
Press ESP again .
•
yPSis displayed once
ESP on ➟ ESP off ➟ Power Save ➟ESP on
•
For in-car use, check that the cassette adapter is inserted correctly, that the car
cassette player’s playback direction is correct (press autoreverse to change),
and that the cigarette lighter jack is clean. Allow time for temperature change.
BELT CLIP
CLIP CEINTURE
CINTURÓN DE CIERRE
LOCK
LIFT
BELT CLIP
RELEASE
English (supplied or optionally available)
1 To attach the belt clip to the CD player, position the shaped grip (found on the back of
the belt grip) so that it fits into the belt clip hole of the CD player. Turn the clip to
LOCK as indicated on the CD player.
2 To detach, gently lift the belt clip and turn to RELEASE as indicated on the CD player.
Français (fourni ou en option)
1 Pour fixer le clip ceinture, placez l’attache (située sur le dos du clip) dans le trou prévu
à cet effet sur l’appareil. Tournez l’attache jusqu’à LOCK, comme indiqué sur l’appareil.
2 Pour enlever l’attache, soulevez-la doucement et tournez-la jusqu’à RELEASE.
Español (suministrado o disponible de forma opcional)
1
Para ponerse el cinturón, encaje el broche (en la parte posterior del cinturón) en el orificio
del cinturón de cierre. Gire el cierre hasta LOCK tal y como se indica.
2
Para quitárselo, levante con cuidado el cinturón y gire hasta RELEASE tal y como se indica.
El aparato cumple las normas FCC, Parte 15 y 21 CFR 1040.10. Funcionamiento
dependiente de dos condiciones siguientes:
1. Este aparato no puede provocar interferencia dañina, y
2. Este aparato debe aceptar cualquier interferencia recibida, incluyendo las
interferencias que pueden provocar un funcionamiento insuficiente.
CAUTION
Use of controls or adjustments or performance of procedures other than
herein may result in hazardous radiation exposure or other unsafe
operation.
L’appareil répond aux normes FCC, Part 15 et 21 CFR 1040.10. Fonctionnement
soumis aux deux conditions suivantes :
1. Cet appareil ne doit pas provoquer d’interférences nuisibles, et
2. Cet appareil doit accepter toute interférence reçue, y compris les
interférences susceptibles de provoquer un fonctionement peu satisfaisant.
ATTENTION
L’utilisation de commandes ou de réglages ou l’exécution de procédures
autres que celles décrites dans le présent manuel risque
d’entraîner une exposition à un rayonnement dangereux ou d’avoir d’autres
conséquences sur la sécurité.
The set complies with the FCC-Rules, Part 15 and with 21 CFR 1040.10.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
PRECAUCIÓN
La utilización de controles o ajustes y la realización de procedimientos
distintos de los contenidos en este manual pueden provocar la
exposición a radiaciones peligrosas y a otros peligros.
Canada
English: This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio Interference Regulations
of the Canadian Department of Communications.
Français : Cet appareil numérique n'émet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de Classe B prescrites
dans le Règlement sur le Brouillage Radioélectrique édicté par le Ministère des
Communications du Canada.
|