Always there to help you
Register your product and get support at
AEA3000
Question?
Contact
Philips
User manual
Contents
1 Important
2
Safety
Notice
2
2
2 YourWireless Microphone and
Receiver
4
4
4
4
Introduction
What's in the box
Overview of the unit
3 Get started
5
5
Install/replace microphone batteries
4 Play
6
6
7
Sing along through the wireless
microphone
Optional: Enjoy music from an existing
Hi-Fi system
5 Product information
8
8
Specifications
6 Troubleshooting
9
EN
1
•
•
Remove batteries when the unit is not
used for a long time.
1 Important
Perchlorate Material-special handling
hazardouswaste/perchlorate.
l Apparatus shall not be exposed to
dripping or splashing, keep it away from
direct sunlight,naked flames or heat.
Safety
Important Safety Instructions
Information about the use of batteries:
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
Caution
• Risk of leakage: Only use the specified type of batteries.
Do not mix new and used batteries. Do not mix
different brands of batteries. Observe correct polarity.
Remove batteries from products that are not in use for
a longer period of time. Store batteries in a dry place.
d Follow all instructions.
e Do not use this apparatus near water.
f Clean only with dry cloth.
• Risk of injury:Wear gloves when handling leaking
batteries. Keep batteries out of reach of children and
pets.
• Risk of explosion: Do not short circuit batteries. Do
not expose batteries to excessive heat. Do not throw
batteries into the fire. Do not damage or disassemble
batteries. Do not recharge non-rechargeable batteries.
g Do not block any ventilation openings.
Install in accordance with the
manufacturer's instructions.
h Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that
produce heat.
Notice
i Only use attachments/accessories
Any changes or modifications made to this
device that are not expressly approved by
Philips Consumer Lifestyle may void the user’s
authority to operate the equipment.
specified by the manufacturer.
j Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
This product complies with the radio
interference requirements of the European
Community.
k Battery usage CAUTION –To prevent
battery leakage which may result in bodily
injury, property damage, or damage to
the unit:
This product is in compliance with the essential
requirements and other relevant provisions of
Directive 1999/5/EC.
A copy of the EC Declaration of Conformity
(DoC) is available in the packaging.
•
Install all batteries correctly, + and - as
marked on the unit.
2
EN
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
“Made for iPad” means that an electronic
accessory has been designed to connect
specifically to iPad, and has been certified by
the developer to meet Apple performance
standards.Apple is not responsible for the
operation of this device or its compliance with
safety and regulatory standards. Please note that
the use of this accessory with iPad may affect
wireless performance.
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC.
iPad is a trademark of Apple Inc., registered in
the U.S. and other countries.
The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by Philips is
under license.
Please inform yourself about the local separate
collection system for electrical and electronic
products.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste. Correct disposal of
your old product helps to prevent potential
negative consequences for the environment and
human health.
Note
• The type plate is located on the back of the unit.
Your product contains batteries covered by
the European Directive 2006/66/EC, which
cannot be disposed with normal household
waste.Please inform yourself about the local
rules on separate collection of batteries
because correct disposal helps to prevent
negative consequences for the environmental
and human health.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
EN
3
b
2 YourWireless
Microphone and
Receiver
d
c
Congratulations on your purchase, and
welcome to Philips!To fully benefit from the
support that Philips offers, register your product
If you contact Philips, you will be asked for the
model and serial number of this apparatus.The
model number and serial number are on the
back of the apparatus.Write the numbers here:
a
a Line out socket
(To use the microphone separately)
Model No. __________________________
Serial No. ___________________________
•
connect to the MIC input socket of an
existing Hi-Fi system.
b Battery compartment
Introduction
With the Philips wireless microphone and
receiver, you can:
c OFF/ON
•
Switch the microphone on or off.
•
connect the receiver to your iPad (or
both your iPad and an existing Hi-Fi
system), and sing along with music
from the app (TheVoice: On Stage)
through the wireless microphone.
d Power indicator
•
Light up red when the wireless
microphone is switched on.
•
Flash red when the battery level is low.
Receiver
b
What's in the box
Check and identify the contents of your
package:
a
c
•
•
•
•
•
Wireless microphone
Receiver
3 x AAA batteries
Quick start guide
Safety sheet
a iPad connector
b Bluetooth® indicator
•
Indicate the Bluetooth® status.
c LINE-OUT
Overview of the unit
Wireless microphone
•
Connect the receiver to an existing
Hi-Fi system.
4
EN
3 Get started
Always follow the instructions in this chapter in
sequence.
Install/replace microphone
batteries
Caution
3
Push back the battery cartridge, then close
the battery compartment.
• Risk of explosion! Keep batteries away from heat,
sunshine, or fire. Never discard batteries in fire.
• Danger of explosion if batteries are incorrectly
replaced. Replace only with the same or equivalent
type.
Note
• Batteries contain chemical substances, so they should
be disposed of properly.
• If you are not going to use the microphone for a long
time, remove the batteries.
• New batteries installed in the microphone support up
to 30 hours of continuous use.
• When the power indicator flashes red, it indicates that
the power level is low and you need to replace the
batteries.
1
Open the battery compartment and take
out the battery cartridge.
2
Insert 3 x AAA batteries (supplied) into
the cartridge with correct polarity (+/-) as
indicated.
EN
5
4
Slide the OFF/ON switch on the wireless
microphone to the ON position.
» The Bluetooth® indicator on the
receiver flashes blue.
4 Play
» The wireless microphone starts to pair
with the receiver automatically.
Sing along through the
wireless microphone
» After successful pairing and connection,
the Bluetooth® indicator turns solid
blue.
Note
• The effective operation range between the wireless
microphone and receiver is approximately 10 meters
(30 feet).
1
Connect your iPad to the receiver.
» A prompt pops up on the iPad screen,
asking you to install the relevant app.
5
Find and download a tutorial from The
Voice: On Stage, then tap Sing->RECORD
for how to sing along through the wireless
microphone and iPad.
2
3
Tap YES on the prompt to install the app
(TheVoice: On Stage) from Apple App
Store.
After successful installation, run TheVoice:
On Stage on the iPad.
6
Select a song from TheVoice: On Stage
and sing along through the wireless
microphone.
6
EN
2
Power on the existing Hi-Fi system and
select the 3.5mm audio input source (see
the user manual of the Hi-Fi system for
detailed operation).
Tip
• If the wireless microphone remains disconnected from
the receiver for more than 15 minutes, it switches to
standby mode automatically.To switch it on again, you
need to slide the OFF/ON switch on the microphone
to the OFF position and then back to the ON position.
• You can use controls available on the app to adjust
sound effects.
• If you experience howling or echo, try to increase the
distance between the microphone and iPad or adjust
the angle of the microphone towards the iPad.
Optional: Enjoy music from
an existing Hi-Fi system
For optimal sound effect, you can connect the
receiver to an existing Hi-Fi system.
MP3 LINK
LINE-OUT
1
Connect a 3.5mm audio cable to:
•
•
the LINE-OUT socket on the receiver.
the 3.5mm audio input socket on your
existing Hi-Fi system.
EN
7
Weight
5 Product
information
0.02kg
0.33kg
•
•
Receiver
Microphone
Note
• Product information is subject to change without prior
notice.
Specifications
Microphone
Power Supply
Directivity
Sensitivity
3 x AAA batteries
Unidirectional
-32 ± 3dB
Receiver
Audio Line Out
1000mV ± 100mV
RMS 20kohm
Frequency Response
100Hz - 16kHz, ±
3dB
Signal to Noise Ratio
Crosstalk
> 85dB
> 40dB
Bluetooth®
Bluetooth® version V2.1 + EDR
Frequency band
2.402-2.480 GHzISM
Band
Range
10m (free space)
General information
Dimensions (W x H
x D)
•
•
Receiver
41.5 x 45.5 x 10.5mm
162 x 333 x 162mm
Microphone
8
EN
Failed to set up connection between the
microphone and receiver
6 Troubleshooting
•
Check whether both the wireless
microphone and receiver are switched
on.The receiver is switched on
automatically when it is connected to
an iPad.
Warning
• Never remove the casing of this device.
•
Make sure that the wireless
To keep the warranty valid, never try to repair
the system yourself.
microphone and receiver are within
the the effective operation range, that
is, approximately 10 meters (30 feet).
If you encounter problems when using this
device, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips Web page (www.
philips.com/support).When you contact Philips,
make sure that the device is nearby and the
model number and serial number are available.
Howling or echo from the wireless
microphone
•
•
Adjust volume on the iPad.
Adjust volume on the existing Hi-Fi
system connected to the receiver.
No power to the wireless microphone
•
Increase the distance between the
microphone and iPad (Hi-Fi system)
or adjust the angle of the microphone
towards the iPad (Hi-Fi system).
•
The batteries may be installed incorrectly
or drained. Install or replace the batteries
batteries' on page 5).
•
As a power-saving feature, the microphone
switches to standby mode automatically
after staying disconnected from the
receiver for more than 15 minutes.To
switch it on again, you need to slide the
OFF/ON switch on the microphone to the
OFF position and then back to the ON
position.
No sound or poor sound
•
•
Adjust volume on the iPad.
Adjust volume on the Hi-Fi system
connected to the receiver.
•
Make sure that you have selected the
correct source on the connected Hi-Fi
system.
•
•
•
Make sure that you have connected the
receiver to the Hi-Fi system securely.
Check whether you have connected the
iPad securely.
Check whether you have started music
play on the iPad.
EN
9
Specifications are subject to change without notice
© 2012 Koninklijke Philips Electronics N.V.
All rights reserved.
AEA3000_UM_00_V1.0
|