|
Multi-Port
Fast Ethernet Print Server
FPS-3121
Quick Installation Guide
This Quick Installation Guide contains brief instructions for the following
environments:
● Windows 95/98/Me/NT/2000/XP/Sever 2003 Peer-to-Peer Networks
● Macintosh (AppleTalk)
For other environments, or any problems, please refer to the full User’s
Manual in the CD-ROM.
Package Content
1 x Print Server
1 x Quick Installation Guide
1 x Drivers and User’s Manual CD
1 x Power Adapter
ꢀ
Physical Installation
1.Make sure the power is OFF then connect printer to the Print Server's
printer port.
2. Connect the LAN cable to the proper connector of the Print Server.
3. Connect the other end of the LAN cable to a 10Base-T or 100Base-TX
hub or switch.
4.Connect the supplied Power Adapter.
5.Please make sure the POWER LED is light on.
ꢁ
Print Server Setup
In the following situation, you do not need to configure the Print
Server. Just follow the procedures on section “Administrator PC Setup”
to share your printer. If you want to install print server to a client PC,
you may refer to our manual in the CD-ROM.
Windows users:
● Already installed TCP/IP protocol.
Apple Macintosh users: Already installed AppleTalk protocol.
ꢂ
Administrator PC Setup
>> Windows Peer-to-Peer Printing
Install Peer-To-Peer Print Driver
1.Insert Drivers and User’s Manual CD into the CD-ROM drive to initiate
the autorun program. Once completed a menu screen will appear.
2.Click on “Administrator Installation” hyper link to initiate the installa-
tion. Or you can click the “Start” button and choose “Run”. (Suppose
“E” is your CD-ROM drive). When the dialog box appears, enter “E:\
Utility\Setup.exe” and press enter key. You will see the dialog box as
below. Please click “Next” to continue.
ꢃ
3. Specify the destination folder where the utility will be installed. Click
“Next”.
4.Select the components you want to install. It is highly recommended
to install all provided components in administrator installation. Please
click “Next”.
ꢄ
5.Specify the program folder name where the program icons will be
add to. Please click “Next” to start installation.
6. For a while, the program will finish installing utility and driver you
selected. Thus far you have completed the installation phase and
prepare to configure the Print Server. The “Choose Print Server”
dialog box will be displayed as following. Please select the print
server and click “Next”.
ꢅ
7. “Name the print Server”, you can assign an easy to memorize name
for management. But note that, this name will be the “Identifier” for
the Peer-to-Peer Printing.
If this is the first time you configure the print server, the
“Print Server Name” will the same as the “Device Name”
printed at the bottom of the print server.
Note
10
8. In the system default, IPX and NetBEUI are enabled. But the Peer-
to-Peer printing is not support those protocols, so it will show those
protocols are not supported. About the TCP/IP, you can either assign
a fixed IP address for the print server or configure it later by the
configuration utility. Please click “Next”.
9. Configuration summary will display in this screen. Now, you have
completed the “Print Server Setup”. By clicking “Finish”, your system
will perform “Add network port” of the print server to your PC.
11
10. The “Setup complete” window is displayed to indicate that the
Administrator Installation procedure is finished. Please click “Finish”.
>> Macintosh (AppleTalk)
1. Click the Apple icon and then Control Panel - Network.
2.Ensure that EtherTalk is selected under AppleTalk Connection.
3. Click Chooser. The Chooser panel will open.
4. Click either the LaserWriter 8 icon (recommended) or the LaserWriter
7 icon.
5.Select a Print Server from the printer list. Print Server names appear
in the form PSxxxxxx (PS followed by 6 digits), as recorded on the
base of the Print Server.
6. Click the Close box. Configuration is now complete.
12
|