POLAR CADENCE SENSOR
POLAR SPEED SENSOR
Model:Y6
User Manual
nload from Www.Somanuals.com. All Manuals Search And Down
1
ID:
ID:
A
2
A
B
nload from Www.Somanuals.com. All Manuals Search And Down
ENG LIS H
Polar Cadence Sensor is designed to measure
cadence, i.e. crank revolutions per minute,
when cycling. Polar Speed Sensor is designed to
measure speed and distance when cycling. The
sensors are compatible with Bluetooth® Smart
Ready devices that support Bluetooth® Cycling
Speed and Cadence Service.
You can use your sensors with dozens of leading
fitness apps as well as with Polar products
using Bluetooth® Smart. Check the compatible
1
nload from Www.Somanuals.com. All Manuals Search And Down
Register your Polar product at
improving our products and services to better
meet your needs.
The latest version of this user manual can be
Please follow the pictures on the front and back
covers.
Write the device ID printed on each sensor in
the space on the front cover (picture 1). The
original marking may fade as a result of
normal wear and tear.
2
EN GL I SH
nload from Www.Somanuals.com. All Manuals Search And Down
Cadence Sensor Parts
1. Cadence sensor (pictures 2 A and 3 A)
2. Cadence magnet (picture 3 B)
Installing the Cadence Sensor
For a video tutorial, see Installing Polar
Cadence Sensor at
To install the cadence sensor and cadence
magnet, you need cutters.
1. Check the chain stay for a suitable place
for the cadence sensor (picture 2 A on the
front cover). Do not install the sensor on
the same side as the chain. The Polar logo
on the sensor should be facing away from
the crank (picture 3 A on the back cover).
2. Attach the rubber part to the sensor
(picture 1 on the front cover).
3. Clean and dry a suitable place for the
sensor and place the sensor on the chain
stay (picture 3 A on the back cover). If the
sensor touches the rotating crank, tilt the
sensor slightly away from the crank. Pass
the cable ties over the sensor and rubber
part. Do not tighten them fully yet.
E N G L I S H
3
nload from Www.Somanuals.com. All Manuals Search And Down
4. Place the cadence magnet vertically on the
inner side of the crank (picture 3 B on the
back cover). Before attaching the magnet,
clean and dry the area thoroughly. Attach
the magnet to the crank and secure with
tape.
5. Fine-tune the positioning of the sensor so
that the magnet passes close to the sensor
without actually touching it (picture 3 on
the back cover). Tilt the sensor towards the
magnet so that the gap between the sensor
and the magnet is under 4
gap is correct when you can fit a cable tie
between the magnet and the sensor. There
is a small caved dot on the backside of the
sensor (picture 1 A on the front cover),
which indicates the spot the magnet should
be pointing at when passing the sensor.
6. Rotate the crank to test the cadence
sensor. The flashing red light on the sensor
indicates that the magnet and the sensor
are positioned correctly. If you keep
rotating the crank, the light will stop
flashing. Tighten the cable ties securely
and cut off any excess cable tie ends.
4
EN GL I SH
nload from Www.Somanuals.com. All Manuals Search And Down
Speed Sensor Parts
1. Speed sensor (pictures 2 B and 4 A)
2. Spoke magnet (picture 4 B)
Installing the Speed Sensor
For a video tutorial, see Installing Polar Speed
Sensor at
To install the speed sensor and spoke magnet,
you need cutters and a cross-head screwdriver.
1. It is recommended to install the speed
sensor on the front fork of your bicycle (as
in picture 2 B on the front cover).
2. Attach the rubber part to the speed sensor
(picture 1 on the front cover).
3. Pass the cable ties over the speed sensor
and rubber part (picture 4 A on the back
cover). Adjust the sensor to the front fork
so that the POLAR logo faces outwards.
Adjust the ties loosely. Do not tighten them
fully yet.
E N G L I S H
5
nload from Www.Somanuals.com. All Manuals Search And Down
4. Attach the magnet to a spoke at the same
level as the speed sensor (picture 4 on the
back cover). There is a small caved dot on
the backside of the sensor (picture 1 A on
the front cover), which indicates the spot
the magnet should be pointing at when
passing the sensor. Fasten the magnet to
the spoke and tighten it lightly with a
screwdriver. Do not tighten it fully yet.
5. Fine-tune the positioning of both the
magnet and the speed sensor so that the
magnet passes close to the sensor but does
not touch it (picture 4 on the back cover).
Move the sensor towards the wheel/spokes
as close as possible. The gap between the
sensor and the magnet should be under 4
can fit a cable tie between the magnet and
the sensor.
6. Rotate the front tire to test the speed
sensor. The flashing red light on the sensor
indicates that the magnet and the sensor
are positioned correctly. If you keep
rotating the tire, the light will stop flashing.
Tighten the screw to the magnet with a
screwdriver. Also tighten the cable ties
securely and cut off any excess cable tie
ends.
Before you start cycling, set the wheel size of
your bicycle into the receiving device or
mobile application.
6
EN GL I SH
nload from Www.Somanuals.com. All Manuals Search And Down
Pairing
Your new sensors must be paired with the
receiving device in order to receive data. For
more information, see the user guidance
material of the receiving device or mobile
application.
To ensure a good connection between the
sensors and the receiving device, it is
recommended to keep the device in a bike
mount on the handlebar.
Care and Maintenance
Keep the sensors clean. Clean them with a mild soap
and water solution, and rinse off with clean water. Dry
carefully with a soft towel. Never use alcohol or any
abrasive material, such as steel wool or cleaning
chemicals. Do not immerse the sensors in water.
Your safety is important to us. Make sure that you can
turn your handlebars normally and that the cable wires
for brakes or gears do not catch the bike mount or
sensors. Also, make sure that sensors do not disturb
pedaling or using the brakes or gears. While riding your
bike, keep your eyes on the road to prevent possible
accidents and injury. Avoid hard hits as these may
damage the sensors.
Replacement magnet sets can be purchased separately.
E N G L I S H
7
nload from Www.Somanuals.com. All Manuals Search And Down
Battery
The batteries cannot be replaced. The sensors are
sealed in order to maximize mechanical longevity and
reliability. To purchase a new sensor, contact your
authorized Polar Service or retailer. You can also
your own country's shoppolar online store.
The battery level of your sensors is displayed on the
receiving device if it supports Bluetooth® Battery
Service.
To increase battery life, the sensors go into standby
mode in thirty minutes if you stop cycling and the
magnets are not passing the sensors.
Frequently Asked Questions
What should I do if...
...the cadence/speed reading is 0 or there is no
cadence/speed reading while cycling?
the magnet are appropriate.
function in the receiving device. For further
information, see the user guidance material of the
receiving device or mobile application.
the handlebar. This may improve the connection.
to temporary electromagnetic interference in your
current surroundings.
empty.
8
EN GL I SH
nload from Www.Somanuals.com. All Manuals Search And Down
...there are irregular cadence, speed, distance or heart
rate readings?
computers. Also WLAN base stations may cause
interference when training with Polar Cadence
Sensor and Polar Speed Sensor. To avoid erratic
reading or misbehaviors, move away from possible
sources of disturbance.
... I want to pair the sensor with the receiving device
before installation?
material of the receiving device or mobile
application. Instead of rotating the crank/wheel,
activate the sensor by moving it back and forth
close to the magnet. The flashing red light indicates
that the sensor is activated.
How do I know...
... if the sensor is transmitting data to the receiving
device?
When you begin cycling, a flashing red light
indicates that the sensor is alive and it is
transmitting cadence/speed signal. As you continue
cycling, the light stops flashing.
E N G L I S H
9
nload from Www.Somanuals.com. All Manuals Search And Down
Technical Specification
-10 ºC to +50 ºC / +14 ºF to +122 ºF
Operating temperature:
Battery life:
Accuracy:
Average 1400 hours of use
±1 %
Material:
Water resistance:
Thermoplastic polymer
Splash proof
FCC ID: INWY6
Cadence Sensor Bluetooth QD ID: B021137
Speed Sensor Bluetooth QD ID: B021136
Copyright © 2014 Polar Electro Oy, FI-90440
KEMPELE.
All rights reserved. No part of this manual may be used
or reproduced in any form or by any means without
prior written permission of Polar Electro Oy. The names
and logos marked with a
or in the package of this product are trademarks of
Polar Electro Oy. The names and logos marked with a ®
symbol in this user's manual or in the package of this
product are registered trademarks of Polar Electro Oy.
The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use
of such marks by Polar Electro Oy is under license.
10
EN GL I SH
nload from Www.Somanuals.com. All Manuals Search And Down
3
A
max 4 mm / 0.16”
B
4
max 4 mm / 0.16”
B
A
nload from Www.Somanuals.com. All Manuals Search And Down
|