Polaroid TV DVD Combo FDM 0700A User Manual

7” Under-the-Counter LCD / DVD

FDM-0700A

Operating Manual

Important Safety Instructions

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USE-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle,

is intended to alert the user to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric to persons.

The exclamation point within an equilateral triangle is intended to alert the

user to the presence of important operating and maintenance (servicing)

instructions in the literature accompanying the appliance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OF MOISTURE.

POWER SUPPLY:

Connect the supplied adapter to the side of the DVD player in the slot marked “DC 12V

IN”. Plug the two-prong end of the power cord to an AC100-240V outlet. If you have

difficulty inserting the plug, turn it over and reinsert it, if the unit will not be used for a

long time, disconnect the plug from the outlet.

NOTE:

Before plugging the power cord into an AC outlet, make sure that all the connections

have been made.

CAUTION:

These servicing instructions are for use by qualified service personnel only. To reduce

the risk of electric shock, do not perform any servicing other than that contained in the

operating instructions unless you are qualified to do so.

Refer to service manual for servicing instructions.

-3-

Important Safety Instructions

Note:

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. DANGER: Visible laser radiation when open and interlock failed or

defeated. Avoid direct exposure to beam.

4. Follow all instructions.

5. Do not use near water.

6. Clean only with dry cloth.

3. CAUTION: Do not open the top cover. There are no user service-

able parts inside the unit. Leave all servicing to qualified service

personnel.

7. Do not block any ventilation openings. Maintain well ventilated conditions around

the product. Do not put product on bed, sofa or anything that blocks ventilation.

Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or

other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide blade or the third prong is

provided for your safety. If the provided plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by

the manufacturer, or sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus combination to avoid

injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of

time.

14. Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or has

been dropped.

15. Apparatus shall not be exposed to dripping or splashing and no objects filled with

liquids, such as vases, shall be placed on the apparatus.

Unauthorized copying, broadcasting, public performance, and lending of disks are

prohibited. This product incorporates copyright protection technology that is protected

by method claims of certain U.S. patents and other intellectual property rights owned

by Macrovision Corporation and other rights owners. Use of this copyright protection

technology must be authorized by Macrovision Corporation, and is intended for home

and other limited viewing uses only unless otherwise authorized by Macrovision

Corporation. Reverse engineering or disassembly is prohibited.

-4-

FCC Notice

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help.

-5-

Characteristic Features

This product incorporates

DVD

Advanced Playing Function

Compatibility

Plays: DVD, CD, CD-R, CD-RW, JPEG

and MP3 discs.

player, LCD display, TV receiver and

radio function in one system. It is

designed for convenient use in the

kitchen. Please refer to page 32 for the

installation instructions.

On-Screen Display

Displays your choice of English, Spanish

or French.

Multiple Mode

Fast Search Function

DVD

Multi-speed, fast forward, fast reverse,

slow play and repeat playback.

Zoom Function

Radio

External Audio

mode

Video Input

Allows the viewer to enlarge in the

picture.

Search By Time

High Quality Property

Video Screen

Search for a certain time on a disc.

Last Memory Playback

Continues playback from a stopped point

as long as power is applied to the DVD

Player.

Supports normal screen (4:3) and wide

screen (16:9) aspect ratios.

AV Input

External Audio、Video input can be

connected to most external AV sources.

LCD (Liquid Crystal Display) screen

Color video screen designed with LCD

technology clearly shows video data.

Amplifier Function

TV Functions

Clear TV signal reception.

Search for TV channels automatically.

Automatically memorize the channels.

Built-in 2x2.5w stereo amplifier with left

and right speakers.

Radio Functions

Clear AM/FM signal reception.

Search for radio stations

automatically.

Switching Power Adapter

Automatically adapts to the voltage

required.

Special Functions

Store radio stations easily.

Search for radio stations in high or

low frequency range.

Supports Multi-language and Parental-

lock features.

-6-

Disc Information

Disc Formats Supported By This Player

PLAYBACK TIME/

PLAYABLE SIDES

DISC LOGO

DIAMETER

133 min (SS-SL)

242 min (SS-DL)

266 min (SS-SL)

484 min (SS-DL)

41 min (SS-SL)

12cm

DVD

75 min (SS-DL)

8cm

82 min (DS-SL)

150 min (DS-DL)

12cm

74 min

8cm

20 min

MP3

12cm

600 min

The disc maker specifies the operation of some DVD discs. Please refer to the

instruction manual with the disc.

Care of Discs

Cleaning of Discs

If a disc has fingerprints or dust on it,

lightly wipe the disc with soft cloth from

the center of the disc outward.

Do not touch the playing surface of the

disc.

Do not stick paper or labels on the disc.

Storage of Discs

Do not expose discs to direct sunlight or

excessive temperatures.

Never use record cleaning sprays, or

any other solvents to clean your discs.

Front Panel

Front Panel Drawing

1. POWER button

Press twice to go to the previous

track/chapter.

Press to enter or exit the STANDBY

mode.

7. SOURCE button

2. PLAY/PAUSE button

Press to start or pause playback under

DVD mode.

Press to shift among DVD, TV,AV,FM

and AM mode.

8. EJECT button

3. Disc Tray

Press to open or close the disc tray.

9. Remote Sensor

Used to load disc.

4. STOP button

Receives remote control signal for

operation.

Press to stop playback under DVD mode.

5. ꢀ

10. Display panel

Press to go to the next track under DVD

mode.

Displays the time, status, radio

frequency and radio station number.

When adjusting volume, the VOL and

volume level will be displayed on the

display panel for several seconds.

6. ꢁ

Under DVD mode, press once to go to

beginning of the current track/chapter.

- 8 -

Front Panel

11. SEEK –/+ button

16. ▲

Under radio mode, press once to fine

tune frequency backward or forward.

Press for about 1.5 seconds to search

radio stations backward or forward

automatically.

Press to select items in the setup menu.

Press to select channels or radio

stations forward under TV or radio mode.

Press to adjust the value upward when

setting the time on the display panel.

17. OK button

Under DVD mode, press to activate fast

backward or forward playback.

12. MUTE button

Press to confirm selections in setup

menu.

Press to turn the speaker output on or

off. The corresponding information will

be displayed on the display panel.

13. SET button

18. ►

Press to select items in the setup menu.

Press to increase the volume. Press to

increase the value in the picture setup

menu.

Press to enter and exit from the timer

setup menu. Press to memorize the

station under AM/FM status.

19. ▼

Press to select items in the setup menu.

Press to select the channels or radio

stations backward under TV or radio

mode.

14. TIME button

Press it once to display the time on the

display panel. In standby status, the time

is still displayed on the panel.

Press it again to set the time on the

display panel. Use the ꢂꢃbuttons to

select the editing position of hour or

minute, and then use the ꢄꢅ buttons to

adjust the value of the hour or minute

upward and downward.

Press to adjust the value downward

when setting the time on the display

panel.

20. TV/LCD SETUP button

Press to enter the TV/LCD setup menu.

21. LCD screen

Presents a high resolution picture.

15. ◄

Press to select items in the setup menu.

Or press to decrease the volume. Or

press to decrease the value in the

picture setup menu.

- 9 -

Rear Panel and display panel

Rear Panel Drawing

1. ANT INPUT jack

4. Left/Right AUDIO input jack

Connected to external antenna to

receive the TV program in TV mode.

2. FM 75Ωcoaxial antenna jack

3. AM antenna jack

Connection for audio input.

5. VIDEO input jack

Connection for video input.

6. Direct current 12V input jack

Display Panel Drawing

1. FM radio status indicator

2. AM radio status indicator

AM time indicator

5. Minute or character indicators

6. Character indicators

7. FM frequency unit of MHz indicator

3. PM time indicator

4. Hour or character indicators

8. AM frequency unit of KHz indicator

- 10 -

Remote Control

Preparation

Using Of Remote Control

Refer to the drawing and remove the

empty battery receptacle.

Point the remote control towards the

main unit when operating. The r/c works

best at a distance less than 7m and at

an angle of up to 60°to the front of the

unit. No obstacles may stand in the way

between r/c and infrared sensor.

Insert the battery into the receptacle.

Make sure the polarity matches the

marks inside the component.

The batteries normally last for about six

months. This depends on how often and

for what operations the remote control is

used.

Insert the receptacle into the remote

control.

If the remote control unit fails to work

even when it is operated near the player,

replace the batteries.

If the r/c is not used for a long period of

time, please remove the batteries from

the compartment, to prevent damage by

leakage.

- 11 -

Remote Control

Remote Control Drawing

- 12 -

Remote Control

1. POWER button

11. SEEK – button

Press to access to or exit the STANDBY

mode.

Under radio mode, press once to fine

tune frequency backward. Press for

about 1.5 seconds to search radio

stations backward automatically.

Under DVD mode, press to activate fast

backward playback.

2. SUBTITLE button

Press to select a subtitle language or to

turn subtitles off when a DVD with multi-

subtitles is playing.

12. SEEK + button

3. DVD button

Press to enter DVD mode.

Under radio mode, press once to fine

tune frequency forward. Press for about

1.5 seconds to search radio stations

forward automatically.

4. TV button

Press to enter TV mode.

Under DVD mode, press to activate fast

forward playback.

5. AV button

Press to shift to external AV input mode.

13. PLAY button

Press to start playback under DVD mode.

6. FM/AM button

Press to shift to FM/AM signal input

mode.

14. STOP button

Press to stop playback under DVD mode.

7. TV/LCD SETUP button

Press to enter the TV/LCD SETUP menu.

15. TITLE button

Press to display titles if present on the

disc under DVD mode.

8. OK button

Press to confirm selections.

16. MENU button

Press to access the disc menu under

DVD mode.

9. ꢂꢃꢄꢅ

Press to select menu items or settings.

Press ꢂꢃ buttons to adjust volume. Or

press to adjust value in the picture setup

menu.

Press ꢄꢅ buttons to select channels or

radio stations forward and backward in

TV or radio mode. Or press to adjust the

value of time when setting time on the

display panel.

17. REPEAT button

Press to repeat a title, chapter, title or

the entire disc.

18. A-B Repeat button

Used to play a section of the DVD from

point “A” to point “B”. Press once to

select the starting point (A) press again

to select the end point (B). Press a third

time to stop the A-B Repeat.

10. SET button

Press to enter and exit from the timer

setup menu. Or Press to memorize the

station under AM/FM status.

- 13 -

Remote Control

19. EJECT button

28. TIME button

Press to open or close the disc tray.

Press it once to display the time on the

display panel. In standby status, the time

is still displayed on the display panel.

Press it twice to set the time on the

display panel. Use the ꢂꢃbuttons to

select the editing position of hour or

minute, use the ꢄꢅ buttons to adjust

the value of the hour or minute upward

and downward.

20. AUDIO button

Press to access various audio languages,

when the DVD disc contains multiple

audio languages.

21. 0-9 number buttons

Select numbers by pressing these

buttons.

29. ꢀ NEXT button

Press to go to the next track under DVD

mode.

22. GOTO button

Press to select the desired disc starting

Time, Track or Title.

30. ꢁ PREV button

23. +10 button

Under DVD mode, press to go to

beginning of current track or chapter.

Press twice repeatedly to go to

beginning of a previous track or chapter.

Select numbers greater than 9 by

pressing the (+10) button first, and then

additional number buttons as needed.

24. 16:9/4:3 button

31. MUTE button

Press to shift the aspect radio between

16:9 and 4:3.

Press to turn on/off the speaker output.

The corresponding information will be

displayed on the display panel.

25. DVD SETUP button

Press to access the DVD setup menu

under DVD mode.

32. PAUSE button

Press to pause playback in DVD mode.

26. INFO button

33. ZOOM button

Press to display detailed playback

information.

Press repeatedly to display additional

information or to turn the information

display OFF.

Press to enter and cycle through zoom

functions, use the direction buttons to

pan around the screen.

34. VOL＋/－

Press to increase or decrease the

speaker volume level.

27. LCD ON/OFF button

Press to turn the LCD screen display on

or off under TV, AV and DVD mode.

35. SLOW button

Press to activate slow forward playback.

- 14 -

System Connections

◆ Do not connect the power cord until all other connections have been made.

◆ Each time you restart the unit, it remembers the last function used.

Connecting To External AV Signal Source

Connections should be made as follows:

Connecting To TV Signal Input Source

- 15 -

System Connections

Connecting To Antenna

Connect the supplied AM/FM antennas to listen to the radio.

◆ In order to improve the signal, move AM loop antenna away from system and other

equipment.

◆ Extend FM antenna fully.

◆ Keep the FM antenna as horizontal as possible after connection.

◆ When connecting the supplied AM loop antenna, connect two black cords to AM and

ground jacks as shown below.

◆ If the FM reception is poor, use a 75Ωcoaxial cable (not supplied) to connect

system to an outdoor FM antenna as above.

◆ If you connect the system with outdoor FM antenna, you should earth the system in

order to avoid lightning strike.

◆ Do not connect the earth wire to gas pipe to prevent gas explosion.

- 16 -

System Connections

Connecting To the Power Adapter

This unit is powered via the switching power adapter (supplied). See the below figure for

details:

1. Connect the AC adapter to jack marked with “DC 12V IN” on the rear panel of the unit.

2. Plug the two-prong end of the power cord to the grounded electrical socket.

3. When not using the unit, turn off the power of the unit first, and then unplug the power

supply to prevent malfunctions.

- 17 -

Radio Function

Radio Function Operation

Press the AM or FM button on the remote control or front panel to enter AM or FM radio

mode. Then press the SEEK+/- button for about 1.5 seconds on the remote control or

front panel to start searching forward/backward from the current frequency. Press the

SEEK+/- button again to stop searching. Radio frequency will be displayed on the

display panel. The frequency range of FM is from 87.5MHz to 107.9MHz, frequency

range of AM is from 520kHz to 1710kHz.

Fine Tuning

Press the SEEK+/- button on the remote control or front panel once to fine tune the

frequency forward/backward under radio mode.

Semi-memorizing radio stations

If you like a radio station and want to store it for later listening, press the SET button to

memorize it. “SAVE X X” will be displayed on the display panel, “X X” represents the

default station number.

There are two methods to organize the memorized stations:

◆ Use the ꢄꢅ buttons to adjust the channel number for your preference, and then

press the SET button again, the station will be memorized with the coded station

number.

◆ Press the SET button again, the station will be automatically memorized with the

default station number in sequence.

You can store radio stations from 0 to 19, total 20FM or 20AM radio stations. If no

buttons are pressed within 3 seconds of pressing the SET button first time, the

frequency will appear on the display panel again, and the station will not be stored.

Accessing memorized radio stations

◆ Press the number buttons on the remote control to access a radio station by its

memory location code.

◆ Press the ꢄꢅbuttons on the remote control or front panel to select the radio

stations forward and backward.

When selecting the stations, the “CH XX” will appear on the display panel, where the

“XX” is the channel number of the stored radio station. After a few seconds, the “CH XX”

disappears and the radio frequency will be displayed once again.

- 18 -

TV Function

Basic Operation

Connect the antenna to the antenna jack on the rear panel. After connecting the

antenna, connect the power supply cord. If the player is in standby mode, press the

POWER button on the front panel to turn on the power.

Press the TV button on the remote control to shift to TV mode.

Press the ꢄꢅ buttons on the remote control, or use the number buttons directly, to

select the desired channel.

Some preferences can be preset:

Picture Parameter Setup

Press the TV/LCD SETUP button once on the remote control to enter PICTURE setup

menu, and screen display as shown:

PICTURE

Brightness

Contrast

Color

Language

Reset

English

EXIT ◄

►TV SETUP

Use the ▼、▲ buttons to select the item you want to set (Brightness, Contrast, Color).

Use the ►, ◄ buttons to adjust, you can adjust the items between 0 and 20.

Use the ▼, ▲ buttons to select the Language, press the ►, ◄ buttons to select English,

French or Spanish.

To restore a setting to the original value, use the ▼、▲ buttons to select Reset, then

press the OK button to confirm the change.

Press the ◄ button on the remote control to exit from the setup menu.

Press the ► button on the remote control to enter TV Setup menu.

TV System Setup

When the ► button is pressed, the TV system setup menu will appear:

TV SETUP

Signal

CATV

Channel

Skip

002

Fine Tuning

Auto Memory

◄ PICTURE

EXIT

►

- 19 -

TV Function

Use the ▼、▲ buttons to select the item you want to set.

Use the ►, ◄ buttons to select the item and enter it.

Press the ► button on the remote control to exit from the setup menu.

Press the ◄ button on the remote control to return to the picture setup menu.

Signal

Use the ► direction button to select CATV TV signal input mode.

Use the ◄ direction button to select AIR TV signal input mode.

Channel

Use the ►, ◄ buttons to change the channel. In CATV input mode, you can select

channels from 2 to 125; in AIR input mode, you can select channels from 2 to 69.

Skip

When the ► button is pressed to turn the function ON, it will skip the current channel

when using ▼、▲ to select channels.

When the ◄ button is used to turn the function OFF, it will play the channels in

sequence when selecting under normal playback status.

Fine Tuning

Use the ▼、▲ buttons to select Fine Tuning, and then press the ►, ◄ buttons to tune

forward or backward from the current channel

Auto Memory

Use the ▼、▲ buttons to select Auto Memory, press the OK button to enter auto

memory mode:

SEARCHING

CH：009

EXIT^：◄

--------------------------------------------

- 20 -

TV Function

The auto memory will take a few minutes. The unit will search channels from the lowest

channel to the highest channel in the standard channel list. When tuning operations are

complete the unit will exit and store the channels by sequence in the memory.

During tuning, press the ◄ button to exit the auto memory.

Use the ▼、▲ direction buttons to select the desired channel from those in memory.

Timer Setup

Press the SET button on the remote control to enter Timer setup menu, the screen will

display as below:

TIMER SET

Timer

OFF

_ _: _ _ am

CATV

Power on

Power off

Signal

Channel

002

Exit: SET

Use the ▼、▲ buttons to select the item you want to set.

Use the ►, ◄ buttons to enter the item and to select.

Press the SET button again on the remote control to exit from the setup menu.

Timer

Use the ►, ◄ direction buttons to select ON or OFF. This function allows you to set the

start time and end time of the desired signal source. No matter what mode the unit is in,

this function will automatically start the playback of the desired signal source.

Select ON to activate the function; select OFF to disable the function.

Power on

To set the playback start time of the signal source, use number buttons to input the

desired start time in sequence of hour, minute. Press the ►, ◄ direction buttons to shift

between am and pm.

- 21 -

TV Function

Power off

To set the playback end time of the signal source, use number buttons to input the

desired time in sequence of hour, minute. Press the ►, ◄ direction buttons to shift

between am and pm. When the playback of the signal source is over, the player will

enter standby mode.

Signal

Use the ►, ◄ direction buttons to select CATV, AIR, FM or AM.

Channel

Use number buttons to input the desired TV channels. In CATV signal input mode, there

are 124 channels to choose from (2-125); in AIR signal input mode, there are 68

channels to choose from (2-69).

Press the ꢄꢅ buttons on the remote control to select the desired channel, or use the

number buttons to input and then press the OK button to confirm.

Note:

The function is active as long as the unit is continuously supplied with power. The unit

will automatically play the selected input signal at the set start time and enter standby

mode at the set end time each day.

- 22 -

AV Function

The player has an additional AV input so it can function as a monitor for a DVD player,

video cassette player, satellite receiver, video game, etc. When an AV source is

connected, press the AV button on the remote control to enter external input AV mode.

Picture Parameter Setup

Press the LCD SETUP button once on remote control to enter PICTURE setup menu,

and screen will display as shown:

PICTURE

Brightness

Contrast

Color

Language

Reset

English

Exit

◄

Use the ▼、▲ buttons to select the item you want to set (Brightness, Contrast, Color).

Use the ►, ◄ buttons to adjust the items between 0 and 20.

Use the ▼, ▲ buttons to select the Language, press the ►, ◄ buttons to select English,

French or Spanish.

Select Reset to return to the factory default settings.

Press the ◄ button on the remote control to exit from the setup menu.

Note:

Under AV mode, if there is no signal, the LCD screen will be turned off automatically.

When connected to an AV signal source, make sure the type of the selected AV signal

source is NTSC.

- 23 -

Play Operation

Preparation

1. Install the unit in the kitchen; refer to page 32 for details.

2. After connecting the unit to the AC power, turn on the unit’s power by pressing the

POWER button on the front panel or the remote control.

3. Press the DVD button on the remote control or the SOURCE button to shift to DVD

mode.

4. Press the EJECT button on the front panel or the remote control to open the disc

tray.

5. Load the disc with the label facing up.

6. Press the EJECT button again to close the disc tray. The player will automatically

search for the disc and start playback.

DVD Playback

Normally there is a selecting menu for DVD discs. You can press the MENU button to

enter the menu, and use the direction buttons to highlight an item you would like to

select. Press the OK button to select it.

Title & Chapter

Normally there are several titles in a DVD disc, and several chapters (sections) in a title.

You can select any title or chapter quickly by entering the relevant number.

Audio

DVD discs can contain up to 8 audio bit streams. For Example: English, Spanish,

French etc.

To select the audio bit stream you prefer press the AUDIO button on the remote control

during playback. The DVD player will play the next audio bit stream every time you

press the AUDIO button in succession.

Note: This function is only available for discs that have several audio bit streams

recorded onto it.

- 24 -

Play Operation

Subtitle

A DVD disc can be recorded with up to 32 subtitles.

Press the SUBTITLE button on the remote control during playback to select the one you

prefer.

NOTE: This function is only available on DVD discs that are recorded with multi-

subtitles.

CD Playback

The player will play all tracks on a CD disc by default. You can use the ꢁ and ꢀ

(PREV/NEXT skip) buttons, or number buttons to select a track.

MP3 playback

MP3 is an Audio compression format, which compresses the audio signal at the rate of

12:1. When using the MP3 format, one disc can record more than 600 minutes of music,

with sound quality that is similar to that of CD discs.

There are many different methods for storing MP3 songs. Usually, one MP3 disc

includes many folders (directories) and every folder includes several files (songs).

Load a MP3 formatted disc into the DVD Player and a menu will be displayed on the

screen. In stop status, press the up/down direction button to select the directory as you

desire and press the OK or PLAY button for confirmation, use the up/down direction

buttons again to select the desired track. In playback status, use the ꢀ or ꢁ button to

select the next or previous track.

•

During MP3 playback, press the previous or next button to turn the page.

There is no search by time or slow playback function for MP3 discs.

- 25 -

Play Operation

JPEG Playback

JPEG is a common picture format that requires small amounts of storage per image and

has low loss in resolution. Hundreds of pictures can be stored on a disc in this format. In

order to view JPEG photo albums, you can ask your film development company to

make a ”PICTURE CD” when they develop your film.

Normal Playback

Load a JPEG disc in. Use the OK button and Left/Right direction button to select a

submenu with picture, and then use the Up/Down direction button to select the contents.

•

Many discs have other contents besides pictures.

Picture Rotation

This can be used only when the picture is normally displayed. Once another picture is

selected, rotation will be cancelled automatically.

During playback, use the direction buttons to rotate the picture.

Zoom and Move

The ZOOM button is used to turn on/off the zoom and move functions.

When this function is turned on, use the REV/FWD SCAN button to control zoom

proportion and the TV screen will display the relevant proportion.

When this function is turned off, the picture will resume normal size. Press the MENU

button to return to menu page.

•

Some JPEG discs may not support rotation or zooming functions.

- 26 -

Playback Functions

Stop

During playback, press the STOP button once on the remote control to stop playback of

a disc. Press the PLAY button and the DVD Player will resume playback of the disc

from the point where it was stopped.

Pause

Press the PAUSE button once on remote control or front panel to pause playback.

Press the PLAY button to resume normal playback.

Resume Playback

Press the STOP button at the point if you wish to stop the playback of a disc. The DVD

Player will memorize the location where playback of the disc was stopped.

Press the PLAY button to resume normal playback. The DVD Player will resume the

playback of the disc from the location where it was stopped. This function will not

operate if the disc is removed from the DVD Player.

Press the STOP button twice (2). Playback of the disc will stop. When the PLAY button

is pressed again, playback of the disc will start from the beginning of disc.

Zoom

Press the ZOOM button on the remote control to cycle through the different zoom

settings.

Fast Playback

Press the ꢆ or ꢇ button on the remote control to activate fast forward or rewind

playback.

Slow Playback

Press the SLOW button to activate slow forward playback.

◆ There is no slow playback for MP3, CD discs.

Search By Time

During DVD disc playback, press the GOTO button on the remote control once, there

will be a menu displayed on the screen. You can set or select items for your preference.

Use the ꢄꢅ direction buttons to select items, press the OK button to enter and use the

ꢄꢅ direction buttons to select the desired item. Press the ꢂdirection button to return.

When select the Title or Chapter, use number buttons to input desired title or chapter.

◆

Some DVD discs do not support the search function.

- 27 -

Playback Functions

Previous and Next

Press the PREV ꢁ button once to return to the currently playing Chapter or Track.

Press the PREV button twice repeatedly and playback will start from the previous

Chapter or Track.

Press the NEXT ꢀ button on the remote control and playback of the disc will start from

the next Chapter or Track.

Repeat

To repeat a Title, Chapter or Track press the REP button on the remote control.

Continually pressing the REP button will display a menu as follows: Repeat Chapter,

Title, All.

You can temporarily select a section of a DVD that you would like to play repeatedly.

You do this by marking the start and the end of the section using the A/B button. During

playback press the A-B button on the remote control at the beginning of the segment

(point A) you wish to play repeatedly. Press the A-B button again to mark the end of the

segment (point B).

The DVD player will automatically return to point A and repeat playback of the selected

segment (A-B). To resume normal playback, press the A-B button again.

Screen Mode

Press the 16:9/4:3 button on the remote control to switch the screen aspect ratio

between 16:9 and 4:3.

- 28 -

System Setup

DVD Setup

You can customize the set up menu to your own preference.

Press the “DVD SETUP” button on the remote control to display the setup menu. The

menu will include “General Setup”, “Speaker Setup”, “Dolby Digital Setup”, “Video

Setup”, and “Preference Setup”. Press the direction button (ꢂꢄꢅꢃ) on the remote

control to select a category. All the items in the category will appear on the screen.

Press the “OK” button to enter the category.