ESPAÑOL: PÁGINA 17
FRANÇAISE : PAGE 31
Instruction
manual
Double Insulated
1
/
2" Right Angle Drill
MODEL 7556
IMPORTANT
Please make certain that the person who is
to use this equipment carefully reads and
understands these instructions before
starting operations.
To learn more about Porter-Cable
visit our website at:
The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.
Model No. ______________________________________
Type ___________________________________________
Serial No._______________________________________
Part No. A08430 - 09-30-04
Copyright © 2002 Porter-Cable Corporation
SAFETY GUIDELINES - DEFINITIONS
It is important for you to read and understand this manual. The information it
contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS.
The symbols below are used to help you recognize this information.
indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
indicates a potentially hazardous situation which, if not
avoided,could result in death or serious injury.
indicates a potentially hazardous situation which, if not
avoided,may result in minor or moderate injury.
used without the safety alert symbol indicates potentially
hazardous situation which, if not avoided, may result in
property damage.
CALIFORNIA PROPOSITION 65
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known (to the State
of California) to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
●
●
●
lead from lead-based paints
crystalline silica from bricks and cement and other masonry products
arsenic and chromium from chemically-treated lumber
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, always wear MSHA/NIOSH
approved, properly fitting face mask or respirator when using such tools.
3
GENERAL SAFETY RULES*
Read all instructions Failure to follow all
instructions listed below may result in electric shock, fire and/or
serious injury. The term "power tool" in all of the warnings listed
below refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
SAVE THESE INSTRUCTIONS
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite
accidents.
b) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will reduce risk of electric
shock
b) Avoid body contact with earthed or grounded surfaces such as
pipes, radiators, ranges and refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled cords increase the risk
of electric shock.
e) When operating a power tool outdoors, use an extension cord
suitable for outdoor use. Use of a cord suitable for outdoor use reduces
the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired
or under the influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in serious personal
injury.
b) Use safety equipment. Always wear eye protection. Safety equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in the off-position
before plugging in. Carrying power tools with your finger on the switch
or plugging in power tools that have the switch on invites accidents.
4
*The text used in the General Safety Rule section of this manual is
verbatim, as required, from the applicable UL60745 3rd edition standard.
continued
GENERAL SAFETY RULES*
d) Remove any adjusting key or wrench before turning the power tool
on. A wrench or a key left attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your
hair, clothing and gloves away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used.
Use of these devices can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the power source before making any
adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to
operate the power tool. Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tools operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly maintained power
tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools
with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in accordance
with these instructions and in the manner intended for the
particular type of power tool, taking into account the working
conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous
situation.
5) Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the
power tool is maintained.
5
*The text used in the General Safety Rule section of this manual is
verbatim, as required, from the applicable UL60745 3rd edition standard.
ADDITIONAL SPECIFIC SAFETY RULES
1. USE AUXILIARY HANDLES SUPPLIED WITH THE TOOL. Loss of
control can cause personal injury.
2. HOLD POWER TOOLS BY INSULATED GRIPPING SURFACES WHEN
PERFORMING AN OPERATION WHERE THE CUTTING TOOL MAY
CONTACT HIDDEN WIRING OR ITS OWN CORD. Contact with a "live"
wire will make exposed metal parts of the tool "live" and shock the
operator.
3. VERIFY the direction of rotation before starting the tool.
4. NEVER ATTEMPT TO CHANGE DIRECTION of rotation while switch is
“ON”. To do so, may damage the drill. Be sure switch is “OFF” and
motor has completely stopped before changing direction of rotation.
5. SOME WOOD CONTAINS PRESERVATIVES WHICH CAN BE TOXIC.
Take extra care to prevent inhalation and skin contact when working with
these materials. Request, and follow, any safety information available
from your material supplier.
6. DO NOT use bits larger than those recommended in Fig. A. They
increase the chance of jamming. Large bits may also overload the drill
and damage the motor and gears.
7. USE ONLY the proper chuck key to tighten or loosen the chuck. Do not
use chuck if jaws or other parts are cracked or worn.
8. NEVER hold work in your hand, lap, or against other parts of your body
when drilling.
9. DO NOT use drill as a router or try to elongate or enlarge holes by
twisting the drill. Drill bits may break and cause injury.
10.
There are certain applications for which this tool was
designed. Porter-Cable strongly recommends that this tool NOT be
modified and/or used for any application other than for which it was
designed. If you have any questions relative to its application DO NOT
use the tool until you have written Porter-Cable and we have advised
you.
Technical Service Manager
Porter-Cable Corporation
4825 Highway 45 North
Jackson, TN 38305
6
SYMBOL
DEFINITION
........................ volts
V
A
........................ amperes
........................ hertz
........................ watts
........................ kilowatts
........................ farads
........................ microfarads
........................ litres
Hz
W
kW
F
µF
l
g
........................ grams
........................ kilograms
........................ bars
........................ pascals
........................ hours
........................ minutes
........................ seconds
........................ no-load speed
kg
bar
Pa
h
min
s
n0
…/min or …min 1 ......... Revolutions or reciprocations per minute
-
or d.c. ................ direct current
or a.c. ................ alternating current
2
........................ two-phase alternating current
2N
3
........................ two-phase alternating current with neutral
........................ three-phase alternating current
3N
........................ three-phase alternating current with neutral
........................ rated current of the appropriate fuse-link in amperes
........................ time-lag miniature fuse-link where X is the symbol
for the time/current characteristic, as given in IEC 60127
........................ protective earth
........................ class II tool
........................ IP symbol
IPXX
7
MOTOR
Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60
cycle A.C. current and voltage within plus or minus 5 percent of that shown on
the specification plate on the tool. Several models, however, are designed for
A.C. current only. Refer to the specification plate on your tool for proper voltage
and current rating.
Do not operate your tool on a current on which the voltage is not
within correct limits. Do not operate tools rated A.C. only on D.C.
current. To do so may seriously damage the tool.
EXTENSION CORD SELECTION
If an extension cord is used, make sure the conductor size is large enough to
prevent excessive voltage drop which will cause loss of power and possible
motor damage. A table of recommended extension cord sizes will be found in
this section. This table is based on limiting line voltage drop to 5 volts (10 volts
for 230 volts) at 150% of rated amperes.
If an extension cord is to be used outdoors it must be marked with the suffix W-A
or W following the cord type designation. For example – SJTW-A to indicate it is
acceptable for outdoor use.
RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS
Length of Cord in Feet
115V
230V
25 Ft.
50 Ft.
50 Ft.
100 Ft. 150 Ft. 200 Ft.
250 Ft. 300 Ft.
500 Ft. 600 Ft.
400 Ft. 500 Ft.
800 Ft. 1000 Ft.
100 Ft. 200 Ft. 300 Ft. 400 Ft.
0-2
2-3
18
18
18
18
18
18
18
16
16
16
14
14
18
18
18
18
16
16
14
14
12
12
12
12
18
16
16
14
14
12
12
10
10
10
8
16
14
14
12
12
10
10
8
16
14
12
12
10
10
8
14
12
12
10
10
8
14
12
10
10
8
12
10
10
8
12
10
8
3-4
4-5
8
5-6
8
6
6-8
6
6
6
8-10
10-12
12-14
14-16
16-18
18-20
8
6
6
4
8
6
6
4
4
8
6
6
6
4
2
8
6
6
4
4
2
8
6
4
4
2
2
8
6
6
4
4
2
2
FUNCTIONAL DESCRIPTION
FOREWORD
Porter-Cable drills are designed to drill holes of various sizes in wood and
metal as indicated in the following chart:
Model No. of Drill Type of Bit
Max. Dia. Hole Material
Low
Twist Drill
Auger Bit
1/2"
13/4"
45/8"
1/2"
Steel
Wood
Wood
Steel
Speed
7556
Self Feed Bit
Twist Drill
High
Speed
Auger Bit
11/2"
29/16"
Wood
Wood
Self Feed Bit
Fig. A
8
CARTON CONTENTS
* Right angle drill
* Side handle
* Chuck key
* Open end wrench
* Pin wrench
ASSEMBLY
INSTALLING AND REMOVING DRILL BIT
1.
DISCONNECT TOOL FROM POWER SOURCE.
2. The three-jaw chuck is designed for self-centering of the drill bit. Open
chuck jaws by turning outer sleeve counterclockwise, when viewing the
chuck from the bit end. Open large enough so that bit shank can be inserted.
3. Clean and insert smooth end of drill bit as far as it will go into the chuck,
then withdraw bit approximately 1/16", or up to the flutes for small bits.
4. While holding the bit with one hand, turn outer sleeve clockwise until bit
is gripped in the chuck.
5. Tighten chuck – insert chuck key into each of 3 keyholes in chuck body
(Fig. 1) in succession and tighten securely by turning key clockwise.
6.
Be sure chuck key is removed before starting tool.
7. To remove bit, reverse this procedure.
TIGHTEN
LOOSEN
Fig. 1
TO INSTALL AUXILIARY HANDLE
An auxiliary handle (C) Fig. 2, is
supplied and can be installed on
either side of the tool. This handle
screws directly into the drill housing
providing complete control of the
drill.
G
A
E
C
B
F
It is strongly recommended that the
auxiliary handle be used and tool
held as illustrated in Fig. 3A during
all drilling operations.
Model 7556
Fig. 2
9
OPERATION
TO START AND STOP DRILL
1. Make sure drill switch is “OFF”. Make sure power circuit voltage is the
same as that shown on the specification plate of the drill. Connect drill to
power circuit.
2. Squeeze TRIGGER SWITCH (A) Fig. 2, to start motor. As trigger is
squeezed, the drill speed increases. Release trigger to stop motor.
3. A REVERSING SWITCH (B) Fig. 2 – is provided with either model. These
models will operate in either the forward direction (clockwise rotation) for
drilling holes, or the reverse direction (counterclock-wise rotation) for
releasing jammed drill bits. For counterclockwise rotation, stop the motor by
releasing the trigger switch and move the reversing switch to the position
labeled “R”, or in the opposite direction for clockwise rotation.
NOTE: Never attempt to change direction of rotation while switch is
“ON”. To do so, may damage the drill. Be sure switch is “OFF” and
motor has completely stopped before changing direction of rotation.
TO INCREASE RPMs
The 7556 is factory assembled with the chuck on drive end marked “LOW” and
will run at the lower RPM shown on the specification plate. To change to the
higher RPM marked on the nameplate proceed as follows:
1.
DISCONNECT TOOL FROM POWER SOURCE.
2. Open chuck jaws as wide as possible to gain access to chuck retaining
screw.
3. Place spindle wrench (furnished with drill) on flats of spindle shaft and hold.
With a 3/16" hex wrench, turn the retaining screw clockwise (left hand threads) and
remove screw from chuck.
4. While supporting chuck on a solid surface, place wrench on flats of spindle
and allow the opposite end of wrench to rest on the workbench to your left as
shown in Fig. 3. Place chuck pin wrench into chuck key hole so that pin wrench
extends to your left as shown in Fig. 3. Strike the pin wrench a sharp blow with a
hammer to loosen chuck.
5. Turn chuck counterclockwise to unscrew. Remove chuck and two washers
from spindle.
6. Loosen the outer sleeve screw (F) Fig. 2 with a 1/2” wrench, and remove the
right angle drive (E) Fig. 2, from the sleeve (G) Fig. 2.
7. Place end of right angle drive marked “LOW” into sleeve (G) Fig. 2. Make
sure the flats on the driveshaft engage slot in coupling. Tighten sleeve screw (F)
Fig. 2.
8. Place steel washer and then brass washer (washers removed in Step 5) onto
spindle at end of right angle drive marked “HIGH.”
NOTE: Failure to use these washers may cause chuck to seize on
spindle.
9. Thread chuck onto spindle and seat firmly by reversing procedure in Step 4.
10. Replace and tighten chuck retaining screw securely.
10
INSTALL CHUCK
REMOVE CHUCK
Fig. 3
The 7556 may be converted to a conventional straight drive drill by loosening
the back sleeve screw and removing the sleeve and right angle drive from
the drill. Remove the coupling retaining screw (hold spindle with spindle
wrench, turn screw clockwise with a 5/32" hex wrench) and coupling. Remove
the chuck and washers from the right angle drive and assemble to drill
spindle.
NOTE: Chuck must be firmly seated on spindle before installing
chuck retaining screw.
HOW TO HOLD THE DRILL
The front end of drill may be made live if the tool drills into live
wiring in a wall. TO PREVENT ACCIDENTAL ELECTRICAL SHOCK, DRILL
MUST BE HELD AS SHOWN IN FIG. 3A.
An auxiliary handle (C) Fig. 2, is supplied with each drill.
GENERAL DRILLING
1. Be sure drill bit is securely gripped in chuck. (See INSTALLING AND
REMOVING DRILL BIT).
2. Set REVERSING SWITCH (B) Fig. 2 for clockwise rotation.
3. Make sure work is held securely in vise or clamped in place prior to
starting drilling operation.
Loose work may spin and cause bodily injury.
4. Locate exact center for hole to be drilled and using a center punch,
make a small dent in work.
5. Place tip of drill bit in dent made by center punch, hold drill square with
work, and start the motor.
6. Apply steady, even pressure to keep drill bit cutting. Too little pressure
will keep the bit from cutting and dull the edges due to excessive friction
created by sliding over the surface.
Too much pressure may cause the bit to break or overheat
resulting in bodily injury or damaged drill bits.
11
RIGHT ANGLE DRILL Model 7556
Fig. 3A
BE ALERT and brace yourself against the twisting action of
the drill, should bit jam in the work.
7. If drill stalls or becomes jammed in the hole, release trigger immediately,
remove drill bit from work and determine cause of stalling or jamming. DO
NOT SQUEEZE TRIGGER ON AND OFF IN AN ATTEMPT TO FREE A
STALLED OR JAMMED DRILL – THIS WILL DAMAGE THE MOTOR. The
direction of rotation may be reversed to help free a jammed bit. Be sure
direction of rotation is RESET before attempting to continue drilling.
8. Reduce the pressure on the drill just before the bit cuts through the work
to avoid splintering wood or stalling in metal.
9. When bit has completely penetrated work and is spinning freely,
withdraw it from the work while the motor is still running, then turn off drill.
DRILLING WOOD
SOME WOOD CONTAINS PRESERVATIVES WHICH
CAN BE TOXIC. Take extra care to prevent inhalation and skin contact
when working with these materials. Request, and follow, any safety
information available from your material supplier.
In addition to the instructions listed under GENERAL DRlLLlNG, the following
also apply:
1. When using twist drills in wood, they should be withdrawn from the hole
frequently to clear chips built up in flutes to avoid overheating and burning
work.
2. If a backing block is used to keep back of work from splintering, it
should be clamped securely in place. If a backing block is not used with
spade bits or auger bits, ease up pressure as soon as bit point breaks
through work, and complete the hole from the opposite side.
DRILLING METAL
In addition to the instructions listed under GENERAL DRlLLlNG, the following
also apply:
When drilling metal, jamming of bit is more likely than
when drilling other materials.
1. Use only good quality sharp high speed steel twist bits when drilling
metal.
12
2. Start drilling with slow speed and gradually increase speed as drill cuts.
The harder the material, the slower the speed required. The softer the
material, the faster the speed.
3. When drilling a large hole, it is easier to first drill a smaller hole and then
enlarge it to the required size.
4. The use of a lubricant, such as oil, on the drill point helps keep the bit
cool, increases drilling action and prolongs drill bit life.
TROUBLESHOOTING GUIDE
list of service centers or call the Porter-Cable help line at 1-800-487-8665.
13
MAINTENANCE
KEEP TOOL CLEAN
Periodically blow out all air passages with dry compressed air. All plastic parts
should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic
parts. They could possibly dissolve or otherwise damage the material.
Wear ANSI Z87.1 safety glasses while using compressed air.
FAILURE TO START
Should your tool fail to start, check to make sure the prongs on the cord plug are
making good contact in the outlet. Also, check for blown fuses or open circuit
breakers in the line.
LUBRICATION
This tool has been lubricated with a sufficient amount of high grade lubricant for
the life of the unit under normal operating conditions. No further lubrication is
necessary.
BRUSH INSPECTION (If applicable)
For your continued safety and electrical protection, brush inspection and
replacement on this tool should ONLY be performed by an AUTHORIZED
PORTER-CABLE SERVICE STATION or a PORTER-CABLE•DELTA FACTORY
SERVICE CENTER.
At approximately 100 hours of use, take or send your tool to your nearest
authorized Porter-Cable Service Station to be thoroughly cleaned and inspected.
Have worn parts replaced and lubricated with fresh lubricant. Have new brushes
installed, and test the tool for performance.
Any loss of power before the above maintenance check may indicate the need
for immediate servicing of your tool. DO NOT CONTINUE TO OPERATE TOOL
UNDER THIS CONDITION. If proper operating voltage is present, return your tool
to the service station for immediate service.
14
SERVICE
REPLACEMENT PARTS
When servicing use only identical replacement parts.
SERVICE AND REPAIRS
All quality tools will eventually require servicing or replacement of parts due to
wear from normal use. These operations, including brush inspection and
replacement, should ONLY be performed by either an AUTHORIZED PORTER-
CABLE SERVICE STATION or a PORTER-CABLE•DELTA FACTORY SERVICE
CENTER. All repairs made by these agencies are fully guaranteed against
defective material and workmanship. We cannot guarantee repairs made or
attempted by anyone other than these agencies.
Should you have any questions about your tool, feel free to write us at any time.
In any communications, please give all information shown on the nameplate of
your tool (model number, type, serial number, etc.).
ACCESSORIES
A complete line of accessories is available from your Porter-Cable•Delta
Supplier, Porter-Cable•Delta Factory Service Centers, and Porter-Cable
Authorized Service Stations. Please visit our Web Site www.porter-cable.com
for a catalog or for the name of your nearest supplier.
Since accessories other than those offered by Porter-
Cable•Delta have not been tested with this product, use of
such accessories could be hazardous. For safest operation,
only Porter-Cable•Delta recommended accessories should
be used with this product.
15
WARRANTY
PORTER-CABLE LIMITED
ONE YEAR WARRANTY
Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original
purchase. We will repair or replace at our option, any part or parts of the product and accessories
covered under this warranty which, after examination, proves to be defective in workmanship or
material during the warranty period. For repair or replacement return the complete tool or accessory,
transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station.
Proof of purchase may be required. This warranty does not apply to repair or replacement required
due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service
Centers or Authorized Service Stations.
ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE
OF PURCHASE.
To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION,
4825 Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING
OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY
AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other legal rights which vary
from state to state.
16
PORTER-CABLE • DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)
(CENTRE DE SERVICE PORTER-CABLE • DELTA)
Parts and Repair Service for Porter-Cable
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable
(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)
•
Delta Power Tools are Available at These Locations
•
Delta)
Cleveland 44125
8001 Sweet Valley Drive
Unit #19
Phone: (216) 447-9030
Fax: (216) 447-3097
ARIZONA
MINNESOTA
Minneapolis 55429
5522 Lakeland Avenue North
Phone: (763) 561-9080
Fax: (763) 561-0653
GEORGIA
Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Phone: (602) 437-1200
Fax: (602) 437-2200
Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Phone: (404) 608-0006
Fax: (404) 608-1123
OREGON
MISSOURI
Portland 97230
CALIFORNIA
North Kansas City 64116
1141 Swift Avenue
Phone: (816) 221-2070
Fax: (816) 221-2897
ILLINOIS
4916 NE 122 nd Ave.
Phone: (503) 252-0107
Fax: (503) 252-2123
Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
Addison 60101 (Chicago)
400 South Rohlwing Rd.
Phone: (630) 424-8805
Fax: (630) 424-8895
PENNSYLVANIA
St. Louis 63119
Willow Grove 19090 (Philadelphia)
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
7574 Watson Road
Phone: (314) 968-8950
Fax: (314) 968-2790
Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: (630) 910-9200
Fax: (630) 910-0360
San Diego 92111
7638 Clairemnot Blvd.
Phone: (858) 277-9595
Fax: (858) 277-9696
NEW YORK
TEXAS
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
MARYLAND
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: (972) 446-2996
Fax: (972) 446-8157
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
NORTH CAROLINA
Charlotte 28270
9129 Monroe Road, Suite 115
Phone: (704) 841-1176
Fax: (704) 708-4625
COLORADO
Houston 77043
4321 Sam Houston Parkway, West
Suite 180
Phone: (713) 983-9910
Fax: (713) 983-6645
MASSACHUSETTS
Arvada 80003 (Denver)
8175 Sheridan Blvd., Unit S
Phone: (303) 487-1809
Fax: (303) 487-1868
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
OHIO
FLORIDA
WASHINGTON
Columbus 43214
4560 Indianola Avenue
Phone: (614) 263-0929
Fax: (614) 263-1238
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: (954) 321-6635
Fax: (954) 321-6638
Auburn 98001(Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: (253) 333-8353
Fax: (253) 333-9613
MICHIGAN
Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: (248) 597-5000
Fax: (248) 597-5004
Tampa 33609
4538 W. Kennedy Boulevard
Phone: (813) 877-9585
Fax: (813) 289-7948
Authorized Service Stations are located in many large cities. Telephone 800-487-8665 or 731-541-6042 for assistance locating one. Parts and
accessories for Porter-Cable Delta products should be obtained by contacting any Porter-Cable Delta Distributor, Authorized Service
Center, or Porter-Cable Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will be directed to
the nearest Porter-Cable Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas grandes ciudades.
Llame al 800-487-8665 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios para los productos Porter-
Cable Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable Delta, Centro de Servicio Autorizado o Centro
de Servicio de Fábrica Porter-Cable Delta. Si no tiene acceso a ninguna de estas opciones, llame al 888-848-5175 y le dirigirán al Centro de
Servicio de Fábrica Porter-Cable Delta más cercano. Des centres de service agréés sont situés dans beaucoup de grandes villes. Appelez au
800-487-8665 ou au 731-541-6042 pour obtenir de l’aide pour en repérer un. Pour obtenir des pièces et accessoires pour les produits Porter-
•
•
•
•
•
•
•
•
Cable
•
Delta, s’adresser à tout distributeur Porter-Cable
•
Delta, centre de service agréé ou centre de service d’usine Porter-Cable
•
Delta. Si
vous n’avez accès à aucun de ces centres, appeler le 888-848-5175 et on vous dirigera vers le centre de service d’usine Porter-Cable
•
Delta le
plus proche.
CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS
QUÉBEC
ALBERTA
MANITOBA
1515 Ave.
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
St-Jean Baptiste, Suite 160
Québec, P.Q.
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
Phone: (403) 735-6166
Fax: (403) 735-6144
Phone: (204) 633-9259
Fax: (204) 632-1976
BRITISH COLUMBIA
8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: (604) 420-0102
Fax: (604) 420-3522
ONTARIO
1447, Begin
St-Laurent, (Mtl), P.Q.
H4R 1V8
Phone: (514) 336-8772
Fax: (514) 336-3505
505 Southgate Drive
Guelph, Ontario
N1H 6M7
Phone: (519) 767-4132
Fax: (519) 767-4131
The following are trademarks of PORTER-CABLE
•
DELTA (Las siguientes son marcas registradas de PORTER-CABLE
•
DELTA S.A.) (Les
marques suivantes sont des marques de fabriquant de la PORTER-CABLE
•
DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®,
Contractor’s Saw®, Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®, Flying
Chips™, FRAME SAW®, Grip Vac™, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-
SET®, Micro-Set®, MIDI LATHE®, MORTEN™, NETWORK™, OMNIJIG®, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-
CABLE®&(design), PORTER-CABLE®PROFESSIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE™, Posi-Matic®, Q-
3®&(design), QUICKSAND®&(design), QUICKSET™, QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®,
Sanding Center®, SANDTRAP®&(design), SAW BOSS®, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®,
The American Woodshop®&(design), The Lumber Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-
LINE™, TIGER®, TIGER CUB®, TIGER SAW®, TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®,
UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®, Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER SERIES®,
WOODWORKER’S CHOICE™.
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries.
Las Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden
estar registradas en otros países. Marques déposées, indiquées par la lettre ™ et ®, sont déposées au Bureau des brevets d’invention et
marques déposées aux Etats-Unis et pourraient être déposées aux autres pays.
7.2-PTG-F-1
|