Included Hardware
M4 x 12mm Phillips
Head Screw
(Qty 4)
¾” Spacer (Qty 4)
INSTALLATION GUIDE: XUF-1330L
M4 x 30mm Phillips
Head Screw
(Qty 4)
2” Wood Screw
(Qty 2)
Victory LCD Wall Mounting System
Bubble Level (Qty 1)
The Victory LCD Mounting System is designed for secure installation of LCD displays of up to
40 lbs. in weight.
Tool List
Phillips/ Slot Head Screw Driver
Electronic Stud Finder
Warning Statements
Allen Wrench (Supplied)
Portable Drill
THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST A MAXIMUM
WEIGHT OF 40 LBS. IF NOT, THE WALL MUST BE REINFORCED. PROPER
INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN
THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO
COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN DEATH.
WARNING:
¼” Masonry Bit for Concrete Installation
NOTE: The included level may be permanently attached
to the wall plate by inserting the level into the
receptacle on the back of the wall plate.
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION
OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION
PROCEDURE TO PREVENT PERSONAL INJURY.
WARNING:
WARNING:
Wood Stud Installation
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS
SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE INSTALLATION
INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY
DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE
LOCATION FOR FUTURE REFERENCE.
NOTE: Using a wood stud finder, locate the stud centers
behind the wall. Once found, make
a
pencil
marking on the center of the wood studs. Once the
mark is made, it is strongly recommended that a
pilot hole be drilled with a 1/8” drill bit.
1. Place the back plate against the wall with the hook
towards the bottom.
2. Secure the back plate using one (1) 2” wood screw.
3. Using the integrated bubble guide, carefully adjust the
back plate until it is level.
A secure structure must support the weight or load of the display. When mounting to a wall that
contains wooden studs, dead center of the wooden stud must be confirmed prior to installation.
Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to
do so could result in damage to the display and/or damage to the mounting surface.
4. Attach the remaining 2” wood screw into the back plate
and tighten.
Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of direct
heat energy. Failure to do so may result in damage to the display and could increase the risk of
fire.
Concrete Installation
NOTE: ¼”
used for concrete installation. They can be
purchased at your local hardware store.
x
2
¼” Threshold anchors must be
At least two qualified people should perform the installation procedure. Injury and/or damage
can result from dropping or mishandling the display.
1. Place the back plate against the wall with the hook
towards the bottom.
2. Level and mark with a pencil the two mounting points
found on the back plate.
3. Next, drill two holes using an electric drill and ¼”
masonry bit.
Recommended mounting surfaces: wooden studs and solid-flat concrete. If the mount is to be
installed on any surface other than wooden studs, use suitable hardware (which is
commercially available).
4. Insert the threshold anchors into the holes that
drilled in the wall.
were
Contact Victory Mounts with any technical / installation questions.
NOTE: If necessary, use a hammer to lightly tap each
anchor into place so that they are flush with the
wall. Once mounted in the wall, unscrew the
slotted cap off of the threshold screw.
5. Once the anchors are in place, set the back plate back
over the concrete anchors.
Threshold
Anchor
6. Using a Slot Head screw driver, attach the back plate by
threading the two slotted caps onto the threaded insert
that is recessed into the wall.
7. Make sure all screws are snug, but be careful
not to over-tighten them.
Slotted Cap
Threaded Insert
Threshold Anchor
|