Power Station II
BATTERY PACK
User Guide
English
Respiratory Care Solutions
1
D
*
2
3
4
E
1
5
4
*
2
3
6
Excluding Elisée / Ausschließlich Elisée / Hors Elisée / Escluso l’Elisée / Excepto Elisée / Excluindo o Elisée / Exclusief Elisée / Exklusive
不包括 呼吸機
Elisée
Elisée / Undtagen Elisée / Unntatt Elisée / Ei Elisée / Δεν περιλαμβάνεται το Elisée / 不包括Elisée呼吸机
/
F
1
2
3a
3b
*
*Example device illustration only / Abbildung eines Beispielgerätes / Exemple d’appareil / Illustrazione dell’apparecchio a solo titolo di
esempio / Ilustración del dispositivo proporcionada a modo de ejemplo únicamente / Ilustração de dispositivo apenas para exemplo /
Uitsluitend voorbeeldillustratie van apparaat / Utrustningen på bilden är endast ett exempel / Det viste apparat er kun til illustrationsbrug /
Den avbildede enheten er kun ment som eksempel / Kuvassa vain esimerkki laitteesta / Απεικόνιση συσκευής παραδείγματος μόνο /
装置样品只是图解 / 裝置只是樣品圖解
Power Station II
DC output voltage & DC cables
DC Cable
Part Number
24V
26V
VPAP™ III ST-A
VPAP™ III ST-A with QuickNav
VPAP™ Auto 25
VPAP™ S, VPAP™ ST
VPAP™ IV, VPAP™ IV ST
S8™ Auto 25
24959
24959
24960
24960
24960
24960
24961
S9™ Series
24959
Stellar™
VS III™
(24981 for Stellar™
Mobility bag)
24963
24962
Elisée™ 150
Notes:
•
•
Not all devices are available in all regions.
Hinweise:
•
•
Einige Geräte sind nicht in allen Ländern erhältlich.
Informationen zu den Akkulaufzeiten finden Sie in der Kompatibilitätsliste Akku/Gerät unter
Remarques :
•
•
Certains de ces appareils ne sont pas disponibles dans tous les pays.
Pour plus d’informations sur l’autonomie des batteries, veuillez consulter la liste de compatibilité
Note:
•
•
Alcuni apparecchi non sono disponibili in tutti i Paesi.
Per informazioni sull’autonomia delle batterie, vedere laTabella di compatibilità tra batterie e
Notas:
•
•
No pueden obtenerse todos los dispositivos en todas las regiones.
Para obtener información sobre la duración de las baterías, consulte la Lista de compatibilidad de
Notas:
•
•
Nem todos os dispositivos estão disponíveis em todas as regiões.
Para obter informações sobre a autonomia das baterias, consulte a lista de compatibilidade entre
NB
•
•
Niet alle apparaten zijn in alle regio’s verkrijgbaar.
Raadpleeg voor informatie over bedrijfstijden van accu’s de Compatibiliteitslijst accu/apparaat op
i
Obs!
•
•
Vissa utrustningar finns inte i alla delar av världen.
För information om batteriernas körtider hänvisas till Produktkompatibilitetslista för batterier/
Bemærkninger:
•
•
Det er ikke alle apparater, der kan fås i alle lande.
Der er oplysninger om batteriers driftstid under Liste over kompatible batterier og apparater på
Merknader:
•
•
Noen apparater er ikke tilgjengelig i alle land.
Huomautukset:
•
•
Kaikkia laitteita ei ole saatavissa kaikissa maissa.
Tietoja akkujen käyttöajoista saat Laitteiden ja akkujen vastaavuus -taulukosta osoitteesta
Σημειώσεις:
•
•
Δεν είναι όλες οι συσκευές διαθέσιμες σε όλες τις γεωγραφικές περιφέρειες.
Για πληροφορίες σχετικά με τους χρόνους λειτουργίας των μπαταριών, ανατρέξτε στο Κατάλογο συμβατότητας
:
:
•
•
不是所有装置都在各个地区有销售。
•
•
不是所有裝置都在各個地區有銷售。
ii
English
Intended use
The ResMed Power Station II (RPS II) is an external lithium-ion battery that provides
power when mains power is unavailable.
Please read the entire guide before using the RPS II. Refer to the device user guides
for intended patients, uses and contraindications associated with CPAP, bilevel and
ventilation therapy.
RPS II at a glance
Refer to illustration A.
The RPS II system comprises the following components:
1. Battery
2. Power supply unit adapter
3. Carry bag
Available separately:
4. 90W AC power supply unit
5. AC power cord
6. DC output cable
Optional accessory:
7. Battery coupler (packed with Velcro™ strap)
Compatible devices and accessories
For a full list of compatible devices for RPS II, see the Battery/Device Compatibility List
page under Ventilation Devices. For a list of output voltages and DC cables for your
device, see the attached information leaflet, your device user guide, or the Battery/
please contact your ResMed representative.
For more information on setting up your device, see your device user guide.
Control panel
Refer to illustration B.
The control panel of your battery includes the following:
1. Audible alert mute button
2. Charge level check button
3. DC on/off switch
4. DC input/output port
5. Audible alert mute indicator
6. Battery level indicators
7. Charging indicator
8. DC switch/discharging indicator
9. Voltage output selector switch (rear
panel)
English
1
Setting up
CAUTION
•
•
Ensure the RPS II and the device are turned off before setting up.
When the RPS II is plugged to the mains power supply, ensure all cables are
properly connected.
Charging the battery
Refer to illustration C.
1. Attach the power supply unit adapter to the DC plug and connect into the battery
DC input/output port.
2. Connect the AC power cord to the power supply unit.
3. Plug the other end of the AC power cord into the mains power outlet.
Notes:
•
•
Charging takes less than 4 hours from 0% battery level to greater than 95%.
To discontinue charging, unplug the AC power cord from the mains power outlet.
Providing power to the device
Refer to illustration D.
1. Select the correct output voltage for your device using the voltage output selector
from the RPS II rear panel.
2. Connect the appropriate DC output cable into the battery.
3. Connect the other end of the DC output cable into the device.
4. Set the DC on/off switch to on.
Providing backup power to the device (for systems with both AC and DC inputs)
WARNING
In this configuration, the Elisee draws power from the RPS II first until it is
fully discharged, and will not recharge. As a result, once all power has been
discharged from the battery, it will not act as an AC backup.
Refer to illustration E.
1. Select the correct output voltage for your device using the voltage output selector
from the RPS II rear panel.
2. Connect the appropriate DC output cable into the battery.
3. Connect the other end of the DC output cable into the device.
4. Connect the AC power cord to the rear of the device.
5. Plug the other end of the AC power cord into the mains power outlet.
6. Set the DC on/off switch to on.
Note: When powering the device regularly check the battery charge level.
Using two batteries
Refer to illustration F.
1. Place one battery on top of another.
If required, use the Velcro strap to hold the batteries securely.
2
2. Plug the battery coupler cables into each of the battery DC input/output ports.
The battery coupler cables are marked with ‘1’ (primary) and ‘2’ (reserve) labels.
3. a. When charging two batteries, attach the power supply unit adapter to the DC
plug and connect the adapter to the the battery coupler.
b. When powering a device, connect the DC output cable of the device to the
end of the battery coupler. The primary battery supplies power to the
device and the reserve battery takes over when the primary battery is
disconnected or discharged.
Indicators
Refer to illustration B.
The RPS II provides LEDs to indicate its current operating state.
LED indicator
Status
Battery charge level1 (B-6)
One amber flashing (audible alert Less than 5%
beeps continuously)
One green flashing (audible alert
beeps for 10 sec)
Less than 10%
One green continuous
Two green continuous
Three green continuous
Four green continuous
10% to 40% (approximate)
40% to 65% (approximate)
65% to 90% (approximate)
Greater than 90% (approximate)
Charging (B-7)
Flashing green
Constant green
Charging
Fully charged
DC on/off (B-8)
Flashing blue
Constant blue
RPS II turned on but not discharging
RPS II turned on and discharging
Audible alert mute (B-5)
Flashing blue
Not discharging and mute is active
Discharging and mute is active
Constant blue
1
When setting the DC on/off switch, the charge level indicator may fluctuate between different levels.
To check the battery charge level, press the charge level check button (B-2) on the
control panel. The number of green LEDs indicates the approximate charge level.
To mute the alert, press the audible alert mute button (B-1). To permanently mute,
press and hold the audible alert mute button (B-1) for 5 seconds. To deactivate, press
the audible alert mute button (B-1) when the mute is still active.
English
3
Using humidifiers
When a device integrated with the HumidAire 2i™ or H4i™ humidifier is not connected
to the mains power supply, the humidifier will only operate in passive unheated mode
despite the warm-up message appearing on the device. When the device is connected
to the mains power supply, it will return to active heated mode.
S9™ and H5i™ devices operate normally in active heated mode when connected to the
battery or to the mains power supply.
Cleaning and maintenance
WARNING
Do not immerse the RPS II in water, and do not use liquids to clean any part of
the product.
1. Disconnect the battery from the power supply unit and the device. Remove all
cables.
2. Wipe the exterior of the battery with a clean cloth.
Storing
CAUTION
Batteries must be charged to 100% indicated by four green LEDs and switched off
before storing.You must recharge the batteries to 100% again after three months
of storage. When not in use, all Lithium-Ion batteries self-discharge over time. If
not periodically recharged (ie, every three months), the RPS II will eventually self-
discharge to the point that it can no longer be recharged. If this occurs the RPS II
is no longer usable and is unrecoverable.
Store the RPS II in a cool, dry place.
Note: A fully charged battery when left switched on, self-discharges to less than 50%
of full capacity within two weeks of storage. Once switched off, the battery self-
discharges to less than 50% of full capacity within one month of storage.
Servicing
The RPS II is intended to provide safe and reliable operation when used and
maintained in accordance with the instructions provided by ResMed. There is no
servicing necessary during the lifetime of the battery.
The service life of the RPS II exceeds 500 recharge cycles. After this cycle, the
battery will last about 60% of the time from its original condition. A full charge in an
older battery will not last as long as in a new battery. ResMed recommends that the
RPS II be tested for battery duration regularly. As with all electrical equipment, if any
irregularity becomes apparent, you should exercise caution and contact an authorised
ResMed service representative.
Traveling
Consult with your carrier if you intend to take the battery on board with your device.
4
Troubleshooting
If there is a problem, try the following suggestions. If the problem cannot be solved,
contact your equipment supplier or ResMed. Do not attempt to open the battery.
Problem/Possible cause
Device is not running
Solution
Power connections are disrupted.
Check all cables and connect them as described in
Setting up.
RPS II is discharged.
Connect the device to the mains power supply and
recharge the RPS II.
RPS II is off.
Set the DC on/off switch to on.
Incorrect output voltage selected.
Select the correct output voltage for your device
using the output voltage selector switch from the
RPS II rear panel.
Note: For a list of output voltages and DC cables
for your device, see the attached information leaflet,
your device user guide, or the Battery/Device
RPS II sounds an audible alert continuously and an amber LED is flashing
The battery charge level is less
than 5%.
Press the audible alert mute button to mute the
alert. Recharge the battery as soon as possible.
RPS II sounds an audible alert for 10 seconds and a green LED is flashing
The battery charge level is below
10%.
Recharge the battery as soon as possible.
Charging stops before completion
When charging the battery inside
the RPS II carry bag, the ambient
temperature is warmer than 35oC.
Remove the battery from the RPS II carry bag or
charge the battery where the ambient temperature is
cooler than 35oC.
Battery turns off and stops powering device
When the battery is in the
Remove the battery from the RPS II carry bag or
RPS II carry bag, the ambient
power the device where the ambient temperature is
temperature is warmer than 35oC.
cooler than 35oC.
Battery charge level indicator is inaccurate
Ambient temperature is at
extreme condition (eg, –5oC,
+40oC).
Recharge the battery as soon as possible to ensure
adequate capacity.
English
5
Technical specifications
Battery technology
Capacity
Lithium ion
< 100 Wh (97 Wh)
UN classification
Power supply
UN3481 (lithium-ion batteries packed with equipment)
Input range 100–240V, 50–60Hz, 1.0-1.5A
Nominal for aircraft use 110V, 400Hz
Battery output voltage
(24V / 26V) 0.5V, 90W continuous
3.75 A
Power supply unit output
current (rated)
Battery output current (rated)
Standby current
3.75 A / 3.46 A
< 100 μA
Protection
Overcharge, overdischarge, excess current, short circuit,
high temperature
Dimensions (L x W x H)
Battery weight
230 mm x 126 mm x 26 mm
0.9 kg
System weight
2.3 kg
Minimum life cycle
≥ 500 cycles at 23°C to 60% capacity
Operating conditions
Charging
Discharging
5°C to 40°C; 5–85% maximum humidity
-5°C to 40°C; 5–85% maximum humidity
Transport/storage conditions
-20°C to +45°C; 5–85% maximum humidity
Operating/storage air pressure 600 hPa to 1100 hPa
Recharge time
< 4 hrs at full level
Electromagnetic compatibility
Product complies with all applicable electromagnetic
compatibility requirements (EMC) according to IEC60601-
1-2, for residential, commercial, and light industry
environments. Information regarding the electromagnetic
emissions and immunity of these ResMed devices can
under Service and Support. Click on the PDF file for your
language.
IEC 60601-1 classification
Battery run time
Class II (double insulation) and/or Internally Powered
Equipment, IP21 (IP20 while charging), Continuous
Operation (from mains), Limited Operation (from
battery), Equipment not suitable for use in the presence
of a flammable anaesthetic mixture with air or with
oxygen or nitrous oxide.
> 8 hrs at average device settings1
For more information, see the Battery/Device
1
Using 15 cm H2O (IPAP), 5 cm H2O (EPAP), and 15 BPM (Respiratory Rate). Not applicable to devices when using
heated humidification and heated tubing.
Note: The manufacturer reserves the right to change these specifications without
notice.
6
Symbols
The following symbols may appear on the device or packaging:
Attention, consult accompanying documents;
Read instructions before use;
Drip proof;
No protection;
Serial number;
Class II equipment;
Catalogue number;
European RoHS;
8
Batch Code;
Maximum humidity;
Temperature limitation (storage and transport);
Charging;
Battery charge
Do not use if
O I
DC on/off;
level;
package is damaged;
Environmental Information.
Audible alert mute;
DC input/output;
Manufacturer;
European Authorised Representative;
Disposal of the battery and the power supply unit should be carried out in accordance with
applicable national laws and regulations. WEEE 2002/96/EC is a European Directive that
requires the proper disposal of electrical and electronic equipment. The battery and power
supply unit should be disposed of separately, not as unsorted municipal waste. To dispose
of your battery and power supply unit, you should use appropriate collection, reuse and
recycling systems available in your region. The use of these collection, reuse and recycling
systems is designed to reduce pressure on natural resources and prevent hazardous
substances from damaging the environment. European Directive 2006/66/EC requires the
proper disposal of spent batteries and accumulators. The battery may only be returned to
collection points fully discharged. If charged or partially discharged, care should be taken to
prevent short circuiting. Batteries containing more than 0.0005% of mercury by mass, more
than 0.002% of cadmium by mass or more than 0.004% of lead by mass are marked below
the crossed-bin symbol with the chemical symbols (Hg, Cd, Pb) of the metals for which the
limit is exceeded.
If you need information on these disposal systems, please contact your local waste
administration. The crossed-bin symbol invites you to use these disposal systems. If you
require information on collection and disposal of your ResMed device please contact your
General warnings and cautions
WARNINGS
•
Lithium ion batteries have built-in safety protection circuits, but can still be
dangerous if they are not used correctly. Damaged batteries can become
inoperative or catch fire.
•
Due to risk of fire or electric shock:
-
-
do not place the RPS II near open fire or heaters.
do not expose the RPS II to direct sunlight or heat (for example behind a
car window).
-
-
-
-
do not expose the RPS II to water, rain or high moisture levels.
do not short-circuit the RPS II.
do not use a damaged RPS II.
do not open the RPS II or the AC charger.
•
Make sure to revert to AC power when the remaining capacity of RPS II and/or
device internal battery is low.
English
7
•
•
•
•
Make sure to periodically recharge the battery due to effects of self-
discharging.
As the battery ages, the available capacity decreases. When the remaining
battery capacity is getting low, do not rely on the RPS II as the primary supply.
Ensure the internal battery of any connected device is kept charged up to
provide backup power in the event of loss of power from RPS II.
Only use a supplied ResMed 90W AC power supply unit for charging the
RPS II.
•
•
Explosion hazard—do not use in the vicinity of flammable anaesthetics.
The RPS II system is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the RPS II system by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the RPS II
system.
Care should be taken to keep the power supply unit adapter dry.The RPS II
system, while connected to a device and discharging, is rated to IP21 (Drip
proof) according to IEC60529. When charging, the RPS II system is rated to
IP20 (No protection) due to the power supply unit adapter which is rated to
IP20.The AC power supply and the RPS II battery are both rated to IP21.
•
•
CAUTIONS
•
•
Avoid hard, physical impact on the battery.
Before using for the first time, ensure that the RPS II and its components are
in good condition and that their operational safety is guaranteed. If there are
any defects, the system should not be used.
•
The RPS II is to be used only in accordance with the intended use stated in
this guide. Damage to equipment or injury can result from modifications to
the equipment or operation.
•
•
•
•
•
Always fully charge the RPS II before use, or before relying as a backup
power.
Monitor the charge level of the RPS II. When the charge level is low, ensure
that continuity of power can be maintained.
When in use, always plug the cable from the RPS II into the device. Keep the
RPS II power switch turned on to ensure it can provide backup power.
When transporting, turn off the RPS II, unplug all cables, and pack in the carry
bag.
Medical electrical equipment requires special precautions regarding EMC and
needs to be installed and operated according to the information provided in
this user guide. Portable and mobile communications equipment can affect
medical electrical equipment. If EMC interference is observed, for example
static on radios, move the RPS II away from other equipment.
Note: The above are general warnings and cautions. Specific warnings, cautions, and
notes appear with the relevant instructions in the guide.
8
Limited warranty
ResMed Ltd (hereafter ’ResMed’) warrants that your ResMed product shall be free
from defects in material and workmanship from the date of purchase for the period
specified below.
Product
Warranty period
• Mask systems (including mask frame, cushion, headgear and
tubing)—excluding single-use devices
90 days
• Accessories—excluding single-use devices
• Flex-type finger pulse sensors
• Humidifier water tubs
• Batteries for use in ResMed internal and external battery systems 6 months
• Clip-type finger pulse sensors
1 year
• CPAP and bilevel device data modules
• Oximeters and CPAP and bilevel device oximeter adapters
• Humidifiers and humidifier cleanable water tubs
• Titration control devices
• CPAP, bilevel and ventilation devices (including external power
supply units)
2 years
• Battery accessories
• Portable diagnostic/screening devices
This warranty is only available to the initial consumer. It is not transferable.
If the product fails under conditions of normal use, ResMed will repair or replace, at its
option, the defective product or any of its components.
This limited warranty does not cover: a) any damage caused as a result of improper
use, abuse, modification or alteration of the product; b) repairs carried out by any
service organisation that has not been expressly authorised by ResMed to perform
such repairs; c) any damage or contamination due to cigarette, pipe, cigar or other
smoke; and d) any damage caused by water being spilled on or into an electronic
device.
Warranty is void on product sold, or resold, outside the region of original purchase.
Warranty claims on defective product must be made by the initial consumer at the
point of purchase.
This warranty replaces all other expressed or implied warranties, including any implied
warranty of merchantability or fitness for a particular purpose. Some regions or states
do not allow limitations on how long an implied warranty lasts, so the above limitation
may not apply to you.
ResMed shall not be responsible for any incidental or consequential damages claimed
to have resulted from the sale, installation or use of any ResMed product. Some
regions or states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation may not apply to you.
English
9
This warranty gives you specific legal rights, and you may also have other rights which
vary from region to region. For further information on your warranty rights, contact
your local ResMed dealer or ResMed office.
10
248527/2 2012-07
Power Station II
USER
ROW MULTI
Respiratory Care Solutions
Manufacturer: ResMed Ltd 1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia.
Distributed by: ResMed Corp 9001 Spectrum Center Boulevard San Diego CA 92123 USA.
ResMed (UK) Ltd 96 Milton Park Abingdon Oxfordshire OX14 4RY UK. See www.resmed.com for other ResMed
locations worldwide.
Designs pending. HumidAire, H4i, H5i, Stellar, VPAP and S9 are trademarks of ResMed Ltd. S9, HumidAire, Stellar and
VPAP are registered in U.S. Patent and Trademark Office. VSIII and Elisée are a trademark of ResMed Paris SAS. Velcro
is a trademark of Velcro Industries B.V.
© 2012 ResMed Ltd.
|