TM 9-6695-244-34P
DEPARTMENT OF THE ARMY TECHNICAL MANUAL
DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE
REPAIR PARTS AND SPECIAL TOOLS LIST
FOR
POWER MAINFRAME, TEKTRONIX MODEL TM506
(NSN 6625-01-048-8920)
Current as of 5 December 1979
Headquarters, Department of the Army, Washington, DC
4 January 1980
REPORTING OF ERRORS
You can help improve this publication by calling atten-
tion to errors and by recommending improvements and
stating your reasons for the recommendations. Your
letter or DA Form 2028, Recommended Changes to
Publications, should be mailed directly to Commander,
US Army Missile Command, ATTN: DRSMI-MFM,
Redstone Arsenal, AL 35809. A reply will be furnished
Directly to you.
Paragraph
Page
1
SECTION I. INTRODUCTION
Scope............................................................................................................................
.............................1
General .........................................................................................................................2
Explanation of columns .................................................................................................3
Special information .......................................................................................................4
How to locate repair parts .............................................................................................5
Abbreviations ................................................................................................................6
1
1
5
5
6
II. REPAIR PARTS LIST ....................................................................................................................... 9
Functional
Group
Group
title
Model
No.
Part
No.
6691
Power Mainframe
TM506
MIS30526/ITYI
III. NATIONAL STOCK NUMBER AND PART
NUMBER INDEX. .........................................................................................................
11
i
PG - Item procured and stocked to provide for sustained support for the life of the equipment.. It is applied to
an item peculiar to the equipment which, because of probable discontinuance or shutdown of production
facilities, would prove uneconomical to reproduce at a later time.
KD - An item of a depot overhaul/repair kit and not purchased separately. Depot kit defined as a kit that
provides items required at the time of over-haul or repair.
KF - An item of a maintenance kit and not purchased separately. Maintenance kit defined as a kit that
provides an item that can be replaced at organizational or intermediate levels maintenance
KB - Item included in both a depot overhaul/repair kit and a maintenance kit.
MO - Item to be manufactured or fabricated at organizational level.
MF - Item to be manufactured or fabricated at the direct support maintenance level.
MH - Item to be manufactured or fabricated at the general support maintenance level.
MD - Item to be manufactured or fabricated at the depot maintenance level.
AO - Item to be assembled at organizational level.
AF - Item to be assembled at direct support maintenance level.
AH - Item to be assembled at general support maintenance level.
AD - Item to be assembled at depot maintenance level.
XA - Item is not procured or stocked because the requirements for the item will result in the replacement of
the next higher assembly.
XB - Item is not procured or stocked. If not available through salvage, requisition.
XC - Installation drawing, diagram, instruction sheet, field service drawing, that is identified by manufacturer's
part number.
XD - A support item that is not stocked. When required, item will be procured through normal supply
channels.
NOTE Cannibalization or salvage may be used as a source of supply for any items coded above except
those coded XA and aircraft support items as restricted by AR 700-42.
(2)
(a)
Maintenance Code. Maintenance codes are assigned to indicate the levels of maintenance
authorized to USE and REPAIR support items. The maintenance codes are entered in the
third and fourth positions of the Uniform SMR Code format as follows:
The maintenance code entered in the third position will indicate the lowest maintenance level
authorized to remove, replace, and use the support item. The maintenance code entered in
the third position will indicate one of the following levels of maintenance:
2
Code Application/Explanation
C - Crew or operator maintenance performed within organizational maintenance.
O - Support item is removed, replaced, used at the organizational level.
F- Support item is removed, replaced, used at the direct support level.
H - Support item is removed, replaced, used at the general support level.
D - Support items that are removed replaced, used at depot, mobile depot, or specialized repair activity only.
(b) The maintenance code enteredin the fourth position indicates whether the item is to be repaired and
identifies the lowest maintenance level with the capability to perform complete repair (i.e., all authorized
maintenance functions). This position will contain one of the following maintenance codes:
Code Application/Explanation
O - The lowest maintenance level capable of complete repair of the support item is the organizational level.
F - The lowest maintenance level capable of complete repair of the support level.
H - The lowest maintenance level capable of complete repair of the support item is the general support level.
D - The lowest maintenance level capable of complete repair of the support item is the depot level.
L - Repair restricted to (enter applicable designated specialized repair activity),
Z - Nonreparable. No repair is authorized.
B - No repair is authorized. The item may be reconditioned by adjusting, lubricating, etc., at the user level. No
parts or special tools are procured for the maintenance of this item.
(3) Recoverability Code. Reactivity codes are assigned to support items to indicate the disposition
action on unserviceable items. The recoverability code is entered in the fifth position of the Uniform SMR
Code format as follows:
Recoverability Codes Definition
Z - Nonreparable item. When unserviceable, condemn and dispose at the level indicated
in position 3.
O - Reparable item. When uneconomically reparable, condemn and dispose at organizational level.
F - Reparable item. When uneconomically reparable, condemn and dispose at the direct support level.
3
H. - Reparable item. When uneconomically reparable, condemn and dispose at the general support level.
D - Reparable item. When beyond lower level repair capability, return to depot. Condemnation and disposal
not authorized below depot level.
L - Reparable item. Repair, condemnation, and disposal not authorized below depot/specialized repair
activity level.
A - Item requires special handling or condemnation procedures because of specific reasons (i.e., precious
metal content, high dollar value, critical material or hazardous material). Refer to appropriate
manuals/directives for specific instructions.
c. National Stock Number (NSN). Indicates the NSN assigned to the item and which will be used for
requisitioning.
d. Part Number. Indicates the primary number used by the manufacturer (individual, company, firm,
corporation, or Government activity), which controls the design and characteristics of the item by means of
its engineering drawings, specifications, standards, and inspection requirements to identify an item or range of
items.
NOTE
When a stock numbered item is requisitioned, the item received may have a different part number than the
part being replaced.
e. Federal Supply Code for Manufacturer (FSCM). The FSCM is a 5-digit numeric code listed in SB 708-42
which is used to identify the manufacturer, distributor, or Government agency, etc.
f. Description. Indicates the Federal item name and, if required, a minimum description to identify the
item. The physical security classification of the item is indicated by the parenthetical entry (insert applicable
physical security classification abbreviation, e.g., Phy Sec Cl (C)-Confidential, Phy Sec C1 (S)-Secret, Phy
Sec Cl (T)-Top Secret). Items that are included in kits and sets are listed below the name of the kit or set with
the quantity of each item in the kit or set indicated in the quantity incorporated in unit column. When the part
to be used differs between serial numbers of the same model, the effective serial numbers are shown as the
last line of the description. In the Special Tools List, the initial basis of issue (BOI) appears as the last line in
the entry for each special tool, special Test, Measurement, and Diagnostic Equipment (TMDE), and other
special support equipment. When density of equipments supported exceeds density spread indicated in the
BOI, the total authorization is increased accordingly.
g. Unit of Measure (U/M). Indicates the standard of the basic quantity of the listed item as used in
performing the actual maintenance function. This measure is expressed by a two-character alphabetical
abbreviation (e.g., ea, in, pr, etc). When the unit of measure differs from the unit of issue, the lowest unit of
issue that will satisfy the required units of measure will be requisitioned.
4
h. Quantity Incorporated in Unit. Indicates the quantity of the item used in the breakout shown on the
illustration figure, which is prepared for functional group, subfunctional group, or an assembly. A "V"
appearing in this column in lieu of quantity indicates that no specific quantity is applicable (e.g., shims,
spacers, etc).
4. Special information
a. Repair parts for components of standards sets which can be identified as existing in the supply
system will be requisitioned through normal supply channels from the appropriate supply commodity
manager.
b. Repair parts for components of standards sets which cannot be identified as to proper supply
source will be requisitioned from USAMICOM, using routing identifier B64 and furnishing as a minimum, the
following as exception data.
(1) Component stock number of the individual end item to be repaired.
(2) Component manufacturer's equipment model number and serial number.
(3) The equipment manufacturer's stock number as listed in the appropriate manual for the
desired repair part.
(4) The repair part reference designation, circuit reference, circuit symbol schematic
designation, or reference number as listed in the manufacturer's manual.
(5) The technical specification of the repair part as contained in the appropriate
manufacturer's manual.
(6) The title and date of the manufacturer's manual from which the information in paragraphs
a, b(3), (4), and (5) above was taken.
NOTE
Repair parts should not be requisitioned for plug-in boards identified in the plug-in boards identified in the
plug-in board exchange program, except by the depot designated to perform the repair. Repair of
calibration set components, with plug-in board assemblies or subassemblies designated as program
exchange replacements with a recoverability code of L, will be accomplished by replacing the plug-in board.
c. The plug-in board exchange program functions are as follows:
(1) Requisitioning instructions for initial issue plug-in boards will be provided since new
instrument boards are included in the program.
(2) As a plug-in board covered by the program fails, a replacement will be requisitioned.
Requisitions will be submitted to Commander, US Army Missile Command, B64, Redstone Arsenal,
AL 35809.
(3) Simultaneously with c(2) above, the defective board being replaced will be shipped by
certified mail, return receipt requested, to the following address:
Transportation Officer
Anniston Army Depot
M/F Field Service Stock
Anniston, AL 36201
When requisitioning a replacement board, the turn-in document number of the replaced board shall be cited
on requisition.
5. How to Locate Repair Parts
a. When NSN or reference number is unknown:
(1) First. Using the table of contents, determine the assembly (functional group) within
which the repair part belongs.
5
(2) Second. Using the repair parts listing, find the functional group to which the repair part
belongs and locate the item by description.
b. When NSN or reference is known:
(1) First. Using the index of NSN's and reference numbers, find the pertinent NSN or
reference number. This index is in ascending NSN cross-referenced to the illustration figure number and item
number.
(2) Second. Using the repair parts listing, find the figure and item number, and locate the figure
and item number in the repair parts list.
6. Abbreviations.The abbreviations listed below may appear in this RPSTL:
AC ------------
ACC --------
alternating current
accordance
ELEC---------
EQUIPM------- equipment
electrical
ACCUR ------ accuracy
F--------------- Fahrenheit
AL-----------
aluminum
FED----------- Federal
FIN------------- finish
AMP ----------
ampere
ASSY --------
ASTM --------
assembly
American Standard
or Testing Materiel
FLG ----------- flange
ATTEN -------
AWG ----------
attenuation
FREQ--------- frequency
American Wire Gage
FSCM---------- Federal supply code
for manufacturer
BAN-----------
banana
FT-------------- foot
BLK------------
BR-------------
C--------------
black
GC-----------
GEN ---------- generator
GHZ ---------- gigahertz
gigacycles
brass
centigrade, calibration, cycles second
CAL ------------ calibrate
CAP---------
CD -----------
CER ----------- ceramic
capacitance
code
GPM ---------- gallons per minute
GPM ---------- gallons per minute
GRAD -------- graduation
COAX -------
coaxial
H -------------
high
COMP---------
composition
HD------------
head
CONDM--------- conductor
HYDR -------- hydraulic
HZ----------- hertz
ID ------------- inside diameter
IN--------- inch
CONN ---------- connector
CONS---------
CONT--------
consisting
continual
COP ----------
copper
INCL - ---------- inclusive
COR ----------
corrosion
K -------------
thousand (prefix)
CPS ----------
CU -------------
cycles per second
cubic
KC-----------
KG-----------
kilocycles
kilograms
CUR ----------
CYL ----------
DB ------------- decibel
DBL----------
DC ------------
DEG ------------ degree
current
cylinder
KHZ ----------
kilohertz
KMHZ -------- thousand megahertz
KV------------ kilovolts
LAB ----------- laboratory
LB----------
LG------------
LT----------
double
direct current
pounds
length
light
DET ----------
detector
DIA -----------
diameter
DIM ------------- dimension
DIV------------ division
DPDT --------- double pole double throw
DPL------------ deployment
6
M ---------------thousand
RPM------------ revolutions per
minute
MA ---------- milliampere
MAX ----------maximum
MC ---------- megacycles
MFD --------- millifarads
MFR ----------manufacturer
MG ---------- milligrams
MHZ ----------megahertz
MIN ----------minimum, minutes
ML ---------- milliliters
MM ---------- millimeters
MOD ----------modified
MSEC ---------milliseconds
MTL ----------material
S -------------
single
SEC---------- seconds
SECT ---------- section
SERR-------- serrated
SHK ---------- shank
SNG ---------- single
SPEC ---------- specification
SPL ---------- special
SQ -------------- square
STD------------ standard
STGT---------- straight
SW ----------- switch
SWR ---------- standing
wave ratio
MV ---------- millivolts
MW---------- milliwatts
NBS---------- National Bureau Standards
NEG --------- negative
NO-------------number
SYS ---------- system
TEL ---------- telescopic
TERM --------- terminal
THD---------- thread
THERM ------- thermometer
THK ---------- thick
NOM--------- nominal
NPT --------- National Pipe Thread
NSN --------- National stock number
OA ------------overall
TSTR --------- tester
U -----------
unit
UF ----------
microfarads
OD ----------- outside diameter
UHF------
ultra high
frequency
OPER --------operating
OZ ----------- ounce
V ------------ volts
VAC ---------- volts alternating
current, vacuum
PCS --------- pieces
PCT ----------percent
PF ------------picofarads
VDC ---------- volts direct current
VHF ---------- very high frequency
VSWR --------- voltage standing
wave ratio
PK ----------- peck
PLTD ------- plated
W ------------ watts, with, width
WT ---------- weight
PN ----------- part number
POS----------positive
PP ---------- peak-to-peak
PSI ---------- pounds per square inch
PWR--------- power
REF---------- reference
REP--------- repetition
REQ -------- required
REQMTS----requirements
RES---------- resistance
RF ----------- radio frequency
RG ---------- range
RH ----------- right hand
RL------------ reel
RM -----------rack mounted
RMS ---------root mean square
ROT ----------rotating
7 (8 BLANK)
SECTION II. REPAIR PART LIST
(2)
(7)
(1)
(5)
(4)
(8)
QTY
INC
IN
(6)
(3)
ILLUSTRATION
DESCRIPTION
NATIONAL
STOCK
NUMBER
(b)
ITEM
NO.
(a)
FIG
NO.
SMR
CODE
PART
U/M
FSCM
UNIT
USABLE ON CODE
NUMBER
GROUP 6691
MAINFRAME, POWER MOD
TM506
MSI30526/1TY1
80009
18876
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
10
20
30
40
50
60
70
80
90
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
5340-00-062-5431 348 0191-00
6225-01-018-2369 161-0033-04
5910-00-546-3271 283-0024-00
5910-00-577-1346 DA49-001CB
5910-01-022-3075 290-0637-00
80009
80009
80009
71590
80009
56286
80009
80009
80009
80009
80009
80009
80009
80009
82877
82877
82877
80009
80009
80009
18876
71400
71400
10001
80009
82877
80009
80009
80009
80009
80009
80009
80009
80009
UMPER.PLASTIC
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
1
1
1
16
4
3
1
1
1
16
16
6
6
6
1
1
1
1
2
1
1
2
1
1
1
1
1
I
4
2
10
1
6
CABLE ASSEMBLY POWER
CAPACITOR,FIXFED
CAPACITOR,FIXEC,CER
CAPACITOR.FIXEC,ELE
CAPACITOR,FIXEC.ELE
CIRCUIT CARD ASSY
CIRCUIT CARD ASSY
CIRCUIT CARD ASSY
CLIP.,ELECTRICL
CONTACT,ELECTRICAL
CCNTACT.ELECTRICAL
CONNECTOR.RECEPTACEL
CCNNECTOR, RECEPTACLE
FAN,TUBEAXIAL
FAN,TUBEAXIAL
FAN,VENTILATING
FILTER MEDIA,AIR
FUSE,CARTRIDGE
FUSE,CARTRIDGE
FUSE,CARTRIDGE
FUSE,CAPTRIDGE.
FUSE,CARTRIDGE
FUSE,ELECTRICAL
FUSEHOLDER, EXTRACTOR
GUARO,MECHANICAL DRIVE
GUIDE
GUIDE
INSULATOR,BUSFING
INSULATOR,BUSING
INSULATORWASER
INSULATOR,PLATE.
KEY,POLAPIZING,ELEC
NUT, PLAIN,HEXAGON
5910-00-467-1548
6695-01-084-9120
6695-01-084-9121
6695-01-084-9122
5999-00-465-9987
5999-00-551-9433
5999-00-396-6331
5935-00-599-8548
5935-00-599-8548
4140-00-726-9755
80D10444
70-3303-00
670-3984-00
670-3834-00
344-0154-00
131-0608-00
131-0707-00
131-1078-00
131-1078-00
WR2A1
100
110
120
130
140
150
160
170
180
190
200
210
220
230
240
260
270
280
290
300
310
320
330
340
350
4140-00-726-9755 WR2A1
4140-00-113-0989
4130-00-281-4034
5920-00-807-8659
5920-00-082-7561
5920-00-284-7466
5920-00-284-7079
5920-00-056-6620
NU2A1
378-0029-00
159-0023-00
159-0027-00
10328857
AGC2-1/2
AGC7-1-2
5920-00-728-6767 59A5A260-3
5920-01-005-9621 382-0362-00
4140-30-227-8228 20132-2
5340-01-056-2929
5340-01-056-2930
251-0286-04
351-0379-01
166-0434-00
PAPFZZ 5970-00-571-8317
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
5970000-451-0436 210-0935-00
5970-01-024-4788 342-0136-00
5970-00-491-0108
5935-00-488-3412
5310-00-00h-8205
386-0978-00
214-1593-02
210-0458-00
4
9
(1)
(7)
(8)
QTY
INC
IN
(6)
(2)
(3)
(4)
(5)
ILLUSTRATION
(a)
FIG
NO.
(b)
ITEM
NO.
DESCRIPTION
NATIONAL
STOCK
NUMBER
SMR
CODE
PART
NUMBER
U/M
UNIT
USABLE ON CODE
FSCM
1
360
370
380
390
400
410
420
430
440
450
460
470
480
490
500
510
520
530
540
540
560
570
580
590
600
610
620
630
650
660
670
680
690
700
710
720
730
740
750
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
PAFZZ
5310-00-655-6534
5310-00-845-7736 NAS671B6
40T10
52983
80205
NUT,PLAIN ASSEMBLED
NUT,PLAIN,.HEXAGCN
511-041800-00 78189 NUT,PLAIN,ASSEMBLED
EA
EA
EA
EA
EA
E A
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
4
2
2
7
1
3
2
12
I
1
32
2
3
1
4
2
1
8
5
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
5310-00-836-3520
5310-00-841-8106
5905-01-014-4756
5905-00-138-4927
5905-30-11C-0992
5305-30-20e-2733
5305-00-316-9526
5305-00-492-2145
53C5-00-625-9546
5305-00-989-3116
5305-01-006-8957
5305-00-418-8251
210-0457-00
308-0734-00
RCR42G102JS
RCR32G511JS
SC10094
212-0082-00
211-0101-00
212-0040-00
MS35206-213
211-0012-00
211-0097-00
80009
80009
81349
81349
80249
80009
80009
80009
96906
83385
80009
NUT,,PLAIN,HEXAGON
RESISTOR,FIXED,FILM
RESISTOR, FIXED,COMP
RFSISTORFIXEO,COMP
SCREW,ASSEMBLED WASHER
SCEW
SCREW,MACHINE
SCREW,,MACHINE
SCREW,MACHINE
SCREW,MACHINE
SCREW,MACHIINE
SCPEW.CAP.HEXAGON HEAD
SCREWW,MACHINE
SCREW,MACHINE
SCREW,MACHINE
SCREW,MACHINE
5305-01-077-0167 212-0511-00
5305-00-40e-0129
53C5-30-63e-0502
80009
8186861
MS35214-28
18876
96906
80009
96906
53C5-00-005-0795 211-0507-00
5305-00-763-7822
5305-00-889-3000
5305-00-841-8060
5961-00-92C-4975
5961-00-131-1197
MS51959-14
MS35206-230
211-0105-00
IN4721 80131
152-0274-30
80009
SCREW,MACHINE
SEMICONDUCTOR DEVICE
SEMICONDUCTOR DEVICE
SW!TCH,ELECTRICAL
SWITCH.PUSH-PULL
SWITCH,PUSH-ULL
SWITCH,E,LECTRIC
TRANSISTOR
TRANSISTOR
TRANSISTOR
TERMINAL,LUG
TERMINAL,LUG
TERMINAL BOARD
TERMINAL,LUG
WASHER,FLAT
WASHER,FLAT
WA5HER,FLAT
EA
EA
EA
EA
EA
EA
.EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
EA
1I
4
4
2
1
1
2
5
1
1
1
1
1
1
1
6
1
4
2
80009
81439
91929
91929
81439
80009
04713
80009
96906
05624
71785
96906
80009
80009
80009
80009
80009
15030-00-829 3251 SE1156363
5930-00-344-2011
5030-00-344-2011
5930-00-829-3251
5961-00-370-1271
5961-01-033-3079
5'61-00-724-2131
5940-00-827-2653
5943-00-156-7344
5940-00-271-4622
5940-00-682-2477
5310-00-192-0631
5310-01-031-7134
5310-C0-113-1494
5310-01-064-7816
5310-03-418-2621
2DM301
2DM301
SE11S6363
151-0373-00
MJ2955
151-0140-00
MS77068-2
FRYE20
1510
MS77068-1
210-0873-00
213-0804-03
210-0851-00
210-0055-00
210-0802-00
WASHER,LOC
WASHER,LOCK
10
FIGURE
NO.
ITEM
NO.
FIGURE
NO.
ITEM
STOCK NUMBER
STOCK NUMBER NO.
5305-00-0C5-C795
5310-00-006-8205
5920-00-056-6620
5340-00-062-5431
5920-00-082-7561
5905-00-110-C992
4140-00-113-C989
5310-00-113-1494
5961-00-131-1197
5905-00-138-4927
5940-00-156-7344
5310-00-192-0631
5305-00-206-2733
4140-00-227-8228
5940-00-271-4622
4130-00-281-4034
5920-00-284-7C79
5920-00-284-7466
5305-00-316- 526
5930-00-344-2011
5930-00-344-2011
5961-00-370-1271
5999-00-396-t331
5305-00-408-0129
5310-00-418e-2621
5305-00-418-8251
5970-00-451-0436
5999-00-4t5-S987
5910-00-467-1548
5935-00-488-3412
5970-00-491-0108
5305-00-492-2145
5910-00-546-3271
5999-00-551-9433
5970-00-571-8317
5910-00-577-1346
5935-00-599-8548
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
I
1
1
1
1
1
1
1
1
1
1
1
I
530
350
230
10
5935-00-599-8548
5305-00-625-9546
5305-00-638-0502
5310-00-655-6534
5940-00-682-2477
5961-00-724-2138
4140-03-726-9755
1
1
1
1
1
1
1
140
460
523
360
703
660
150
160
240
540
190
670
590
620
380
560
390
370
550
470
570
260
480
400
20
200
420
170
73C
580
410
680
710
430
27C
690
180
220
210
440
60C
610
630
120
510
750
490
310
100
60
414C-00-726-9755 1
5920-00-728-6767
5305-00-763-7822
1
1
592C-00-807-8659 1
5940-00-827-2653
1
593C-30-829-3251 1
5930-30-829-3251
5310-00-836-3520
1
1
53C5-00-841-806C 1
5313-00-841-8106
5310-00-845-7736
5305-30-889-3000
5305-00-889-3116
5961-00-929-4975
592}-01-005-9621
1
1
1
1
1
1
53305-31-306-8957 1
5905-01-314-4756
6625-01-018-2369
5910-01-022-3075
5970-01-024-4788
5310-01-331-7134
5961-01-033-3079
5340-31-056-2929
5340-01-056-2930
5310-01-364-7816
5305-01-077-0167
6695-31-084-9120
6695-01-084-0121
6695-01-084-9122
1
1
1
1
1
1
1
1
1
1
1
1
1
53
320
720
650
280
290
740
500
73
340
330
450
30
110
300
40
1
1
1
83
90
13C
FIG.
NO.
ITEM
PART
FIG.
ITEM
FSCM NO.
NUMBERFSCM
NO.
NO.
AGC2-1/2
AGC7-1-2
71400
71400
71590
05624
04713
96906
96906
96906
96906
96906
96906
82877
80205
81349
81349
80249
81439
81439
82877
82877
80131
18876
80009
80009
80009
80009
80009
80009
71785
80009
80009
80009
80009
80009
91929
91929
82877
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
220
230
40
210-0055-00
210-0457-00
80009
80000
80009
80009
80009
80009
80009
80009
83385
80009
80009
80009
80009
80009
80009
80009
80009
80009
80009
80009
80309
80009
80009
80009
80009
80039
80009
80009
52983
78189
10031
80009
80009
80009
56289
18876
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
740
390
350
750
720
730
710
310
480
490
450
560
533
460
440
503
340
30
0A149-001CB
FRYE20
210-0458-00
210-0802-00
210-0804-00
210-0851-00
210-0873-CO
210-0935-00
211-0012-00
211-0097-00
211-0101-03
211-0105-00
211-0507-30
212-004-00
212-0082-00
212-0511-00
214-1593-02
283-0024-00
290-0637-00
308-0704-03
342-0136-30
344-0154-00
348-0191-00
351-028604
351-0379-01
352-0362-00
378-0029-30
386-0978-00
40710
680
650
470
550
520
540
700
670
170
370
420
410
430
590
620
150
160
570
210
110
120
130
140
660
630
690
580
190
200
20
MJ2955
MS35206-213
MS35206-230
MS35214-28
MS51959-14
MS77068-1
M577068-2
MU2A1
NAS67186
RCR325GS11JS
RCR42G1O2JS
SC10094
SE11S6363
SEll156363
WR2A1
50
W2AI
400
320
100
13
1N4721
10328857
131-0608-00
131-0707-C0
131-1078-00
131-1078-00
151-0140-00
151-0373-00
1510
283
293
263
180
330
360
380
240
70
152-0274-00
159-0023-00
159-0027-C0
161-0033-04
166-0434-00
20M301
511-041800-30
59A5A260-3
670-3303-00
670-3834-00
670-3984-00
68010444
90
300
600
610
270
83
60
20M301
20132-2
8186861
510
11
By Order of the Secretary of the Army:
E. C. MEYER
General, United States
Army
Official:
Chief of Staff
J. C. PENNINGTON
Major General, United States Army
The AdjutantGeneral
Distribution:
To be distributed in accordance with DA Form 12-34A, requirements for Calibration Procedures
Publications
*U.S. GOVERNMENT PRINTING OFFICE: 1980-640217/311
|