W236 NA 333-095002
TIMEX® WATCHES
Congratulations on purchasing your TIMEX® watch.
Please read these instructions carefully to
understand how to operate your Timex timepiece.
Your watch may not have all of the features
described in this booklet.
For more information, and to register your product
please visit:
ENGLISH
TABLE OF CONTENTS
2
3
How to Start Your Watch
Water and Shock Resistance
Indiglo® Night-Light
Date Models
4
5
7
Day/Date/Am/Pm/Sun/Moon Models
Perpetual Calendar
Chronograph
9
11
21
22
24
25
27
Tachymeter Function
How to Adjust Bracelet
Bracelet Link Removal
Battery
Warranty
ENGLISH
ENGLISH
HOW TO START YOUR WATCH
WATER AND SHOCK RESISTANCE
To start your watch remove the plastic guard from
under the crown, then press the crown in against the
case. The second hand will begin advancing in one-
second intervals.
If your watch is water-resistant, meter marking
(WR_M) is indicated.
Water-Resistance Depth
p.s.i.a. * Water pressure
Below Surface
Some deep-depth water-resistant watches require
the setting crown to be screwed in to secure water-
resistance. If your watch case has a protrusion with
screw threads, the crown must be screwed in after
setting the watch.
30m/98ft
60
50m/164ft
100m/328ft
200m/656ft
86
160
284
To screw in, push the crown firmly against the
threaded protrusion and hold in while turning the
crown clockwise. Continue to screw in the crown
until it is tight. You will need to unscrew the crown
(counter-clockwise) before pulling it out the next time
you want to set your watch.
*pounds per square inch absolute
WARNING: TO MAINTAIN WATER-RESISTANCE,
DO NOT PRESS ANY BUTTONS OR PULL OUT
THE CROWN UNDER WATER UNLESS YOUR
WATCH IS INDICATED AS 200 METER WATER-
RESISTANT.
1. Watch is water-resistant only as long as crystal,
crown and case remain intact.
2
3
ENGLISH
ENGLISH
2. Watch is not a diver watch and should not be
used for diving.
3. Rinse watch with fresh water after exposure to
salt water.
4. Shock-resistance will be indicated on the watch
face or caseback. Watches are designed to pass
ISO test for shock-resistance. However, care
should be taken to avoid damaging the crystal.
DATE MODELS
TO SET TIME:
1) PULL crown all the
way out and turn to
correct time.
2) Push crown in to
restart. For screw-in
setting crown, push
crown in while turning
CLOCKWISE to tighten.
DATE
A
B
C
CROWN
POSITION
INDIGLO® NIGHT-LIGHT
Press button or crown to activate light.
Electroluminescent technology used in the INDIGLO®
night-light illuminates entire watch face at night and
in low light conditions.
Watches with date: Note correct time of day (A.M or
P.M.) for proper date function.
TO SET DAY:
1) PULL crown to “middle” position and turn
CLOCKWISE until correct day appears. If day does
not change, pull crown to “out” position and turn
CLOCKWISE or COUNTERCLOCKWISE through
necessary number of 24 hour periods until
correct day appears.
4
5
ENGLISH
ENGLISH
DAY/DATE/AM/PM/
TO SET QUICK DATE® FEATURE:
3-Position Crown:
SUN/MOON MODELS
1) Pull crown to “Middle” position and turn CLOCK-
WISE or COUNTERCLOCKWISE until correct date
appears.
DATE
DAY
2-Position Crown:
A
B
C
1) Pull crown to “OUT” position and turn CLOCKWISE
until date changes. Repeat until correct date
appears. Adjust date when month has less than
31 days. Push crown in when finished.
CROWN
POSITION
Caution: Wearing or storing the watch with the crown
in the "middle" position will cause damage to the move-
ment. Always return the crown to the normal position, or
if you wish to save the battery life while storing the
watch, leave the crown in the "out" position.
AM/PM
SUN/MOON
TO SET TIME:
1) PULL out crown to “C” position.
2) TURN crown clockwise to correct time.
Day/am/pm/moon will also change.
3) Push in crown to “A” position.
NOTE: Remember to set time for am or pm (sun or
moon.)
The date function advances the date between the
hours of 10 PM and 2 AM. Avoid setting the date
during this timeframe. If you attempt to set the date
during this time period, rotate the crown at a very
slow rate to avoid damaging the watch.
6
7
ENGLISH
ENGLISH
TO SET DATE:
PERPETUAL CALENDAR
1) PULL out crown to “B” position.
2) TURN crown clockwise to correct date.
3) PUSH in crown to “A” position.
Your Perpetual Calendar watch accurately keeps
track of how many days are in each month. It also
adjusts for leap years. The date on your watch
(including the month and year) was preset at the fac-
tory to Eastern Standard Time, Greenwich Mean Time
or Hong Kong Standard Time (depending on where
you purchased your watch). You only need to adjust
the time.
TO SET DAY:
1) PULL out crown to “C” position.
2) Advance time 24 hours to change the day.
3) PUSH in crown to “A” position.
MIDDLE
OUT
WED 14
WED 14
CHECK DATE
(FACTORY USE ONLY)
SET TIME DAY, DATE
TO SET TIME
To set time, simply pull crown all the way out and
turn. Day and date change automatically when time
is adjusted past midnight; there is no additional step
8
9
ENGLISH
ENGLISH
for setting day or date. Push crown in when done.
CHRONOGRAPH
WITH INDIGLO® NIGHT-LIGHT
After setting, if date changes at noon, time needs to
be adjusted ahead or back 12 hours.
THIS CHRONOGRAPH HAS TWO FUNCTIONS:
TIME & STOPWATCH
If crown is accidentally put in MIDDLE position and
turned, date display will change temporarily, but date
setting is unaffected. Simply pull crown all the way
out and set time. Proper date display will resume.
MINUTE
PUSHER “A”
CHRONOGRAPH
CHRONOGRAPH
1/20 SECOND
CROWN
MINUTE
POSITION
D
➧ A
B
C
HOUR
CHRONOGRAPH
SECOND
PUSHER “B”
DATE
SECOND
BASIC OPERATIONS
•
6 o’clock eye shows seconds.
•
10 o’clock eye shows “minutes elapsed” for
chronograph.
•
2 o’clock eye shows “1/20 seconds elapsed” for
chronograph.
10
11
ENGLISH
ENGLISH
•
Chronograph second hand shows “seconds
elapsed” for chronograph.
3. PUSH crown in to “A” position.
NOTE: The date changes automatically every 24
TIME
hours.
TO SET THE TIME:
CHRONOGRAPH
THE CHRONOGRAPH IS CAPABLE OF
MEASURING:
1. PULL crown out to “C” position.
2. TURN crown either way to correct time.
3. PUSH crown in to “A” position.
•
•
•
1/20 seconds elapsed up to 1 second (2 o’clock
eye).
Seconds elapsed up to 1 minute (chronograph
second hand).
Minutes elapsed up to 30 minutes (10 o’clock
eye).
TO ADJUST TO A NEW TIME ZONE:
1. PULL crown out to “B” position.
2. TURN crown either way to move the hour hand in
hour increments.
CALENDAR
TO SET THE CALENDAR:
1. PULL crown out to “B” position.
NOTE: Chronograph will operate continuously for
4 hours, after which it will automatically stop and
reset.
2. TURN crown either way to move hour hand. Two
complete revolutions relative to the 12 o’clock
position will move the date forward or backward.
This will correct both date and 24-hour time.
NOTE: The 1/20th of a second hand does not
move during chronograph function, the 1/20th
seconds are indicated when chronograph is
stopped and not yet reset.
12
13
ENGLISH
ENGLISH
BEFORE USING THE CHRONOGRAPH, adjust all
the chronograph hands to the “0” or 12-hour
positions.
STANDARD CHRONOGRAPH
MEASUREMENT:
1. PRESS pusher “A” to start timing.
2. PRESS pusher “A” to stop timing.
3. PRESS pusher “B” to reset.
TO ADJUST CHRONOGRAPH HANDS:
1. PULL crown out to “B” position.
2. PRESS pusher “B” until the hand at the 10 o’clock
eye resets to the “30” position.
3. PULL crown out to “C” position.
SPLIT TIME MEASUREMENT:
1. PRESS pusher “A” to start timing.
2. PRESS pusher “B” to split.
4. PRESS pusher “A” until the chronograph second
hand resets to the “0” or “60” or 12-hour posi-
tion.
5. PRESS pusher “B” until the hand at the 2 o’clock
eye resets to the “0” position.
3. PRESS pusher “B” to resume timing.
4. PRESS pusher “A” to stop timing.
5. PRESS pusher “B” to reset.
INDIGLO® NIGHT-LIGHT
With the crown in the “A” position, PUSH crown to
the “D” position. Entire dial will be illuminated.
Electroluminescent technology used in INDIGLO®
night-light illuminates entire watch face at night and
in low light conditions.
6. PUSH in Crown to “A” position.
NOTE:
•
Make sure the chronograph is stopped and reset
before adjusting.
•
PRESSING and HOLDING either pusher “A” or “B”
for 2 seconds will cause the hands to move
continuously until the pusher is released.
14
15
ENGLISH
ENGLISH
CHRONOGRAPH
NIGHT-MODE® FEATURE
TO USE NIGHT-MODE® FEATURE:
DISPLAYS AND BUTTONS
1. PUSH and HOLD Crown to “D” position for 4 sec-
onds to activate NIGHT-MODE® feature. PRESSING
any pusher will cause the INDIGLO® night-light to
stay on for 3 seconds.
CHRONOGRAPH
SECOND
PUSHER “A”
CHRONOGRAPH
MINUTE
2. NIGHT-MODE® feature will last for 8 hours.
MINUTE HAND
CHRONOGRAPH
CROWN
3. Or PUSH and HOLD Crown to “D” position for 4
7
HOUR
POSITION
seconds to deactivate Night-Mode® feature.
B
C
NORMAL POSITION “A”
PUSHER “B”
HOUR
IF STOPWATCH HANDS DO NOT RETURN TO
“0 POSITION” WHEN THE STOPWATCH IS
RESET:
SMALL SECOND
DATE
1) PULL out the crown to “B” position
2) PRESS pushers “A” or “B” repeatedly to move
hands to “0” position
SETTING THE TIME
1) PULL the crown out to the 2nd position “C”.
2) Turn the crown to set hour and minute hands.
3) When the crown is pushed back to the normal
position “A”, small second hand begins to run.
3) PUSH in the crown to “A” position
16
17
ENGLISH
ENGLISH
minute hand, and chronograph hour hand return
to zero position.
SETTING THE DATE
1) PULL the crown out to the 1st position “B”.
2) Turn the crown counter-clockwise to set the date.
*If the date is set between the hours of around
9:00 PM and 1:00 AM, the date may not change
on the following day.
TIME MEASUREMENT
RESET
STOP
3) After the date has been set, push the crown back
to the normal position “A”.
CHRONOGRAPH RESET (INCL. AFTER
REPLACING BATTERY)
USING THE CHRONOGRAPH
This chronograph is able to measure and display time
in 1/1 second united up to maximum of 11 hours
59 minutes 59 seconds. The chronograph second
hand keeps continuously for 11 hours 59 minutes
59 seconds after starting.
This procedure should be performed when the
chronograph second hand does not return to zero
position after the chronograph has been reset, and
including after the battery has been replaced.
1) Pull the crown out to the 2nd position “C”.
MEASURING TIME WITH THE
CHRONOGRAPH
1) The chronograph can be started and stopped
each time pusher “A” is pressed.
2) Press pusher “A” to set the chronograph second
hand to the zero position. The chronograph hand
can be advanced rapidly by continuously pressing
pusher “A”.
3) Once the hand returns to zero position, return the
crown to the normal position.
2) Pressing pusher “B” resets the chronograph and
the chronograph second hand, chronograph
18
19
ENGLISH
ENGLISH
*Do not push crown to normal position while the
chronograph second hand returns to zero position.
It stops on the way when crown is returned to
normal position and its position is recognized as
zero position.
TACHYMETER FUNCTION
The tachymeter will only determine speeds greater
than 60 units per hour using this method; slower
speeds can be measured by decreasing the unit of
measurement. The function performed by a
tachymeter is independent of the unit of distance
(e.g. statute miles, nautical miles, kilometers, meters
etc.) as long as the same unit of length is used for all
calculations.
1) Determine the start and finish markers for your
pre-determined distance.
2) Start the chronograph once the target for speed
measurement passes the start marker.
3) Stop the chronograph once the target for speed
measurement passes the finish marker.
4) The chronograph second hand is compared to the
tachymeter markings to determine the target’s
speed.
20
21
ENGLISH
ENGLISH
FOLDOVER CLASP
HOW TO ADJUST BRACELET
(Variations of the following bracelet sections apply to
all watch models).
BRACELET
1. Find spring bar that con-
nects bracelet to clasp.
2. Using a pointed tool, push
in spring bar and gently
twist bracelet to disen-
gage.
3. Determine wrist size, then
insert spring bar in correct
bottom hole.
SLIDING CLASP BRACELET
1
Open locking plate.
Fig. 1
2. Move clasp to desired bracelet length.
3. Exert pressure while holding locking plate and
slide clasp back and
forth until it engages in
grooves on underside
of bracelet.
4. Press locking plate
down until it snaps
4. Push down on spring bar,
align with top hole and
release to lock in place.
Fig. 2
Fig. 3
closed. Clasp can be
damaged if excessive force is used.
22
23
ENGLISH
ENGLISH
BRACELET LINK REMOVAL
REMOVING LINKS:
BATTERY
FOR PERPETUAL CALENDAR MODELS:
1. Place bracelet upright
and insert pointed tool
in opening of link.
2. Push pin forcefully in
direction of arrow until
link is detached (pins
are designed to be difficult to remove).
3. Repeat until desired number of links are removed.
7-YEAR BATTERY LIFE* WITH
FREE LIFETIME REPLACEMENT**
If the battery needs to be changed, we recommend
that only TIMEX replace it. Your watch will need to be
recalibrated to correct time and date after changing
the battery. To return your watch to Timex use a pre-
paid shipper. To obtain a pre-paid shipper please call
1-800-448-4639 or visit the retailer where you pur-
chased your watch or go to www.TIMEX.com. Please
include the following with your watch to cover
postage and handling (this is not a repair charge); a
U.S.$8.00 check or money order in the U.S.; a
CAN$7.00 cheque or money order in Canada; In other
countries Timex will charge you for postage and han-
dling.
RE-ASSEMBLY:
1. Rejoin bracelet parts.
2. Push pin back into link
in opposite direction
of arrow.
3. Press pin down
securely into bracelet
until it is flush.
*Battery life estimates are based on certain
assumptions regarding usage: battery life may vary
depending on actual usage.
24
25
ENGLISH
ENGLISH
** Shipping & handling charges apply.
TIMEX INTERNATIONAL WARRANTY
Your TIMEX® watch is warranted against manufacturing
defects by Timex Group USA, Inc. for a period of ONE YEAR
from the original purchase date. Timex and its worldwide
affiliates will honor this International Warranty.
NEVER INCLUDE A SPECIAL WATCHBAND
OR ANY OTHER ARTICLE OF PERSONAL
VALUE IN YOUR SHIPMENT.
Please note that Timex may, at its option, repair your
watch by installing new or thoroughly reconditioned and
inspected components or replace it with an identical or
similar model. IMPORTANT — PLEASE NOTE THAT THIS
WARRANTY DOES NOT COVER DEFECTS OR DAMAGES TO
YOUR WATCH:
1) after the warranty period expires;
2) if the watch was not originally purchased from an
authorized Timex retailer;
3) from repair services not performed by Timex;
4) from accidents, tampering or abuse; and
5) lens or crystal, strap or band, watch case, attach-
ments or battery. Timex may charge you for replacing
any of these parts.
FOR ALL OTHER MODELS:
Timex strongly recommends that a retailer or jeweler
replace battery. If applicable, push reset button when
replacing battery. Battery type is indicated on case-
back. Battery life estimates are based on certain
assumptions regarding usage; battery life may vary
depending on actual usage.
DO NOT DISPOSE OF BATTERY IN FIRE. DO NOT
RECHARGE. KEEP LOOSE BATTERIES AWAY
FROM CHILDREN.
THIS WARRANTY AND THE REMEDIES CONTAINED HEREIN
ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PUR-
POSE. TIMEX IS NOT LIABLE FOR ANY SPECIAL, INCIDENTAL
26
27
ENGLISH
ENGLISH
OR CONSEQUENTIAL DAMAGES. Some countries and states
do not allow limitations on implied warranties and do not
allow exclusions or limitations on damages, so these limi-
tations may not apply to you. This warranty gives you spe-
cific legal rights and you may also have other rights, which
vary from country to country and state to state.
2815-0091. For the U.K., call 44 020 8687 9620. For
Portugal, call 351 212 946 017. For France, call 33 3 81 63
42 00. For Germany/Austria, call 43 662 889 2130. For the
Middle East and Africa, call 971-4-310850.
EXTENDED WARRANTY
To obtain warranty service, please return your watch to
Timex, one of its affiliates or the Timex retailer where the
watch was purchased, together with a completed original
Watch Repair Coupon or, in the U.S. and Canada only, the
completed original Watch Repair Coupon or a written
statement identifying your name, address, telephone num-
ber and date and place of purchase. Please include the fol-
lowing with your watch to cover postage and handling
(this is not a repair charge): a US$ 8.00 check or money
order in the U.S.; a CAN$7.00 cheque or money order in
Canada; and a UK£2.50 cheque or money order in the U.K.
In other countries, Timex will charge you for postage and
handling. NEVER INCLUDE A SPECIAL WATCHBAND OR ANY
OTHER ARTICLE OF PERSONAL VALUE IN YOUR SHIPMENT.
Available in U.S. only. Extend your warranty for an addi-
tional 4 years from date of purchase for $5. You can pay
with AMEX, Discover, Visa or MasterCard by calling 1 800-
448-4639 during normal business hours. Payment must be
made within 30 days of purchase. Name, address, tele-
phone number, purchase date, and 5-digit model number
required. You can also mail a check for $5 to: Timex
Extended Warranty, P.O. Box 1676, Dept. EF, Little Rock, AR
72203.
©2010 Timex Group USA, Inc. TIMEX, NIGHT-MODE and
QUICKDATE are registered trademarks of Timex Group
USA, Inc. INDIGLO is a registered trademark of Indiglo
Corporation in the US and other countries.
For the U.S., please call 1-800-448-4639 for additional war-
ranty information. For Canada, call 1-800-263-0981. For
Brazil, call +55 11 5572 9733. For Mexico, call 01-800-01-
060-00. For Central America, the Caribbean, Bermuda and
the Bahamas, call (501) 370-5775 (U.S.). For Asia, call 852-
28
29
|