TS90 Series Sprinklers with Optional TurfCup™
Specifying Information – TS90 Series Sprinkler
TS90TP-02XX-X-E
Description
Threads
TurfCup™
Nozzle
Optional
TS90TP
02
XX
X
E
TS90TP—TS90TP 1” (25mm) Toro 02—NPT thread
TC--TurfCup™ option 1, 2, 3, 4, 5, 6, 7, 8, 9 E–Effluent
with TruJectory
Example: A TS90 Series sprinkler with TruJectory, NPT threads, TurfCup™, and 82’ (25m) radius would be specified as:
TS90TP-02TC-6
Specifications
Radius: 53’-95’ at 25° (16,2 –
29,0m) trajectory
Flow rate: 14.0-61.5 gpm (53-233
lpm)
Precipitation rate: .56-.60”/hr
(14,2-15,2mm/hr)
Arc: Full- & Part-circle in one
-Full-circle: 360° unidirectional
clockwise rotation
-Part-circle: 40°-330°
Rotation Speed: 3 minutes ± 30
seconds
-Body diameter: 4” (402mm)
Dimensions, TurfCup versions:
-Body height: 10” (254mm)
-Overall popped-up height: 14.5”
(37mm)
-Retracted height: 10.7” (27mm)
-Overall pop-up height: 4”
(402mm)
-Pop-up height to main nozzle
from top of outer cover: 1”
(25mm)
-Body diameter: 4” (402mm)
-Overall diameter with stabilizing
spacer: 6.25” (16mm)
horizontal. The option of a back
nozzle shall be available.
The sprinkler shall have both full-
circle and adjustable part-circle
operation in a single unit. The
sprinkler shall be minutely adjustable
from 40° to 360° in part-circle mode.
It shall be adjustable in all phases of
installation (i.e., before installation,
after installation while static, and
after installation while in operation).
When in 360° mode, it shall rotate
only in the clockwise direction. The
sprinkler shall be equipped with a
self-adjusting stator to ensure
constant rotation speed regardless of
nozzle installed.
The sprinkler shall have a clutch
mechanism to allow the nozzle turret
to be manually advanced to the ends
of its arcs, thus allowing quick
Recommended operating pressure
range: 40-100 psi (2,8-7,0 Bar)
Nozzle options: 9 main, 3
intermediate, 1 inner, 1 molded-in
inner (no molded in inner on
TurfCup™ versions)
Inlet size: 1” (40mm) NPT or BSP
Check valve capable of checking up
to 10’ (3m) of elevation difference
Rubber cover for personnel safety
and protection
Bidding Specifications
The sprinkler shall be of gear-
determination of arc limits, without
having to wait for the gear drive
mechanism to drive the nozzle turret
to the limits. The sprinkler shall have
hard arc limits that provide the
operator with positive end of arc
stops when manually advancing the
nozzle turret. The riser shall have a
ratchet feature that allows the entire
riser/nozzle turret assembly to be
rotated to a new position, when not
under water pressure.
The sprinkler shall be equipped
with a drain check valve to prevent
low head drainage, and be capable of
checking up to 10 feet in elevation
change. The sprinkler shall have a
minimum of 4-inch pop-up stroke to
drive, rotary type, capable of
covering a _____ foot (meter) radius
at _____ PSI (bar; kPa) with a
Available in TurfCup™ versions
for seamless on-field installations
on natural and artificial turf sports
field installations
Effluent indicator plug for
installation on rubber cover
Dimensions, non-TurfCup
versions:
-Body height: 10” (254mm)
-Overall popped-up height: 12.5”
(317mm)
-Retracted height: 8.5” (216mm)
-Overall pop-up height: 4”
(402mm)
discharge rate of _____ GPM (lpm).
The sprinkler shall be available with
nine (9) distinct main nozzles for
distance coverage, three (3) distinct
intermediate nozzles for mid-range
coverage, one (1) inner nozzle for
close-in coverage and one (1) molded
in inner nozzle (not available for
TurfCup™ versions) for mid-close-
range coverage. The nine (9)
different nozzle sets shall be formed
by combinations of the main,
intermediate and inner nozzles. The
main nozzle shall be adjustable from
7° to 30°, in 1° increments, from
-Pop-up height to main nozzle: 3”
(75mm)
-Exposed cap diameter: 2.2”
(26mm)
June 2012
|