INSTRUCTION MANUAL
CAMERA CONTROL UNIT
IK-TF9U
For Customer Use
Enter below the Serial #
which is located on the
bottom of the cabinet. Retain
this information for future
reference.
Model #:
Serial #:
IK-TF9U
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class A digital device, pursu-
ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
USER-INSTALLER CAUTION:Your authority to operate this FCC verified equipment could be voided
if you make changes or modifications not expressly approved by the party responsible for compliance
to Part 15 of the FCC Rules.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est comforme à la norme NMB-003 du Canada.
Following information is only for EU-member states:
The use of the symbol indicates that this product may not be treated as household waste.
By ensuring this product is disposed of correctly, you will help prevent potential negative con-
sequences for the environment and human health, which could otherwise be caused by inap-
propriate waste handling of this product. For more detailed information about the takeback
and recycling of this product, please contact your supplier where you purchased the product
or consult.
This manual is made from 100% recycled paper.
Note the following instructions when installing.
• Do not cover the product by any material.
• Do not put the product on an Inflammable material such as carpet or blanket.
• Do not put the product in a narrow space, since the heat generated from the
product may be difficult to emanate.
If you do not follow the above, the heat generated by the product may cause fire.
Do not placing the product in direct sunshine and/or high temperature.
Temperature build up inside the product may result in fire.
Avoid setting in humid, smoky, vaporized or dusty places.
This may cause fire and/or electric shock.
Ask your dealer to perform a periodical check and internal cleaning (approx.
once every five years).
Dust inside the product may cause fire and/or trouble. For check and cleaning
cost, please consult your dealer.
The following description is for that a camera head “IK-TF9H” connected to this camera control unit.
Do not point the lens directly at the sun and/or intensive light such as di-
rect sunlight, etc.
Focusing of the light may cause injury of eye and/or fire.
Disclaimer
We disclaim any responsibility and shall be held harmless for any damages or losses incurred by the
user in any of the following cases:
1. Fire, earthquake or any other act of God; acts by third parties; misuse by the user, whether inten-
tional or accidental; use under extreme operating conditions.
2. Malfunction or non-function resulting in indirect, additional or consequential damages, including
but not limited to loss of expected income and suspension of business activities.
3. Incorrect use not in compliance with instructions in this instruction manual.
4. Malfunctions resulting from misconnection to other equipment.
5. Repairs or modifications made by the user or caused to be made by the user and carried out by
an unauthorized third party.
6. Notwithstanding the foregoing, Toshiba’s liabilities shall not, in any circumstances, exceed the
purchase price of the product.
Limitation of Usage
The product is not designed for any “critical applications.” “Critical applications” means life support
systems, exhaust or smoke extraction applications, medical applications, commercial aviation, mass
transit applications, military applications, homeland security applications, nuclear facilities or sys-
tems or any other applications where product failure could lead to injury to persons or less of life or
catastrophic property damage. Accordingly, [Toshiba/TAIS] disclaims any and all liability arising out
of the use of the product in any critical applications.
Protection of Personal Information
Images taken by the camera that reveal the likeness of an individual person may be considered
personal information. To disclose, exhibit or transmit those images over the internet or otherwise,
consent of the person may be required.
3
Copyright and Right of Portrait
There may be a conflict with the Copyright Law and other laws when a customer uses, displays,
distributes, or exhibits an image picked up by the camera without permission from the copyright
holder. Please also note that transfer of an image or file covered by copyright is restricted to use
within the scope permitted by the Copyright Law.
TABLE OF CONTENTS
1. CAUTIONS ON USE AND INSTALLATION ..... 5
2. COMPONENTS ................................................ 5
3. NAMES AND FUNCTIONS .............................. 6
4. CONNECTION .................................................. 7
(4. 6) Changing the manual shading correction
seting ................................................ 22
( 5 ) SYNC ...................................................... 22
(5. 1) Adjusting horizontal phase............... 22
( 6 ) OPTION .................................................. 22
(6. 1) Changing serial communication baud
rate .................................................... 22
( 7 ) Setting to factory setting status............... 23
7. 3 Synchro. Scan Operation ........................ 23
( 1 ) Setting by 2H .......................................... 23
( 2 ) Setting by the frame ................................ 23
7. 4 E. TRG (External trigger)......................... 24
4. 1 Standard Connection ................................ 7
4. 2 Cautions on Connection ........................... 7
4. 3 Connector Pin Assignments ..................... 7
5. OPERATION ..................................................... 8
5. 1 Automatic Black Balance .......................... 8
5. 2 White Balance........................................... 8
6. ITEMS CONTROLLED BY USING
ON SCREEN DISPLAY .................................. 10
( 1 ) 1P SNR
(1 Pulse Trigger Sync Non Reset)........... 24
(1. 1) 1 Pulse Trigger SYNC-NON RESET
Picture Output Timing ...................... 24
7. MODE SETTING BY ON SCREEN DISPLAY .... 11
7. 1 Using the Menus ..................................... 11
7. 2 Menus ..................................................... 12
( 1 ) SHUTTER (Electronic shutter)................ 12
(1. 1) Changing each setting in
( 2 ) 1P SR (1 Pulse Trigger Sync Reset) ....... 25
(2. 1) 1 Pulse Trigger SYNC-RESET Picture
Output Timing ................................... 25
( 3 ) PW SNR (Pulse width trigger
MANU mode ..................................... 13
(1. 2) Changing each setting in
SS (synchro. scan) mode ................. 14
(1. 3) Changing each setting in
SYNC-NON RESET) .............................. 26
(3. 1) Pulse Width Trigger SYNC-NON RESET
Picture Output Timing ...................... 26
( 4 ) PW SR (Pulse width trigger
E.TRG mode..................................... 15
(1. 3. 1) Changing each setting in
1P SNR mode ............................... 15
(1. 3. 2) Changing each setting in
1P SR mode ................................. 16
(1. 3. 3) Changing each setting in
PW SNR mode ............................. 17
(1. 3. 4) Changing each setting in
PW SR mode ................................ 18
(1. 3. 5) Changing each setting in
RR mode ....................................... 18
SYNC-RESET) ....................................... 27
(4. 1) 1 Pulse Width Trigger SYNC-RESET
Picture Output Timing ...................... 27
( 5 ) RR (Reset restart) .................................. 28
(5. 1) Long Term Exposure ........................ 28
(5. 2) Input Timing Chart Example ............ 28
7. 5 Partial Read ............................................ 29
( 1 ) Partial Scanning OFF
(All pixels scanning) ................................ 29
( 2 ) Partial Scanning ON ............................... 29
( 3 ) When Partial Scanning Mode is ON ....... 29
7. 6 External Sync .......................................... 30
( 1 ) External sync signal polarity ................... 30
( 2 ) External sync frequency range ............... 30
( 2 ) GAIN (Video gain)................................... 19
(2. 1) Changing each setting in GAIN ........ 19
( 3 ) WHT BAL (White balance)...................... 20
(3. 1) Changing each setting in AWB
(Automatic White Balance) mode .... 20
(3. 2) Changing each setting in MANU
(Manual) mode ................................. 20
( 3 ) Using the unit with external sync signal .. 30
(3. 1) H (horizontal) phase adjustment...... 30
8. OUTPUT WAVEFORM TIMING CHART............. 31
( 4 ) PROCESS .............................................. 21
(4. 1) Changing gamma correction ............ 21
(4. 2) Changing master pedestal ............... 21
(4. 3) Changing R pedestal ........................ 21
(4. 4) Changing B pedestal ........................ 21
(4. 5) Changing the shading
( 1 ) Horizontal Output Waveform Timing Chart ... 31
( 2 ) Vertical Output Waveform Timing Chart... 31
9. SPECIFICATIONS .......................................... 32
10. EXTERNAL APPEARANCE DIAGRAM...... 33
11. BEFORE MAKING A SERVICE CALL ........ 33
correction mode ............................... 22
4
This product is 3CCD color camera with digital video output.
1. CAUTIONS ON USE AND INSTALLATION
Handling the unit.
The following descriptions are for that a camera head
“IK-TF9H” connected to this camera control unit.
•
Do not drop, jolt, or vibrate, as this may result in
damage to the unit. This may cause problems.
Treat the camera cables carefully to prevent cable
problems, such as breaks in the cable and loose
connections.
Do not shoot intense light.
•
If there is an intense light at a location on the
screen such as a spot light, a blooming and smear-
ing may occur. When intense light enters, vertical
stripes may appear on the screen. This is not a
malfunction. Ghosts may occur when there is an
intense light near the object. In this case, change
the shooting angle.
Install the camera in a location free from noise.
•
•
If the camera or the cables are located near power
utility lines or a TV, etc. undesirable noise may
appear on the screen. In such a case, try to change
the location of the camera or the cable wiring.
Moire
•
Operating ambient temperature and humidity.
A moire pattern is an interference pattern gener-
ated when two repetitive line patterns overlap.This
is not a malfunction. Eliminating the repetitive line
patterns, or aligning the two patterns, will elimi-
nate the moire.
Do not use the camera in places where tempera-
ture and humidity exceed the specifications. Pic-
ture quality will deteriolate and internal parts may
be damaged.
Handling of the camera head and protection
cap.
•
Be particularly careful when using in places ex-
posed to direct sunlight. When shooting in hot
places, depending on the conditions of the object
and the camera (for example when the gain is in-
creased), noise in the form of vertical strips or
white dots may occur. This is not a malfunction.
Keep the camera head and protection cap away
from as they may pose a choking hazard.The pro-
tection cap protects the image sensing plane when
the lens is removed from the camera head, do not
discard.
When not using the camera for extended peri-
ods of time.
•
•
When cleaning the camera.
•
Switch the control unit off and disconnect the
power supply.
Unplug the power source before cleaning. Clean
with a soft dry cloth only. Do not use chemicals or
chemically treated cloths. Chemicals may damage
coatings and printed letters. When cleaning the
lens, use lens cleaning paper.
Avoid using or storing the camera in the fol-
lowing places:
Places filled with highly flammable gas.
Places near gasoline, benzene, or paint thinner.
Places subject to strong vibration.
Installation without a tripod.
•
Before installing the camera head, make sure that
the location can withstand the total weight of the
camera head.
Places containing chemicals (such as pesticides),
rubber or vinyl products for extended periods of
time.
If this is not the case, reinforce the area to pre-
vent the unit from dropping, which may result in
damage to the unit or personal injury.
2. COMPONENTS
(1) Camera Control Unit ......................................................................................................................1
(2) Accessories
(a) Instruction manual ...................................................................................................................1
5
3. NAMES AND FUNCTIONS
8
2
4
DC IN 12V terminal
DISP button
1 Camera cable for
‘IK-TF9H’ terminal
MENU UP button
(AWB)
DISP
6
7
DATA UP (AWB) button
DATA DOWN button
MENU DATA
DC IN 12V
PAGE
5 MENU DOWN button
9
DIGITAL terminal
3 PAGE button
[ Front ]
[ Rear ]
12
10
11
[ Bottom ]
[ Top ]
Camera cable for ‘IK-TF9H’ terminal
DISP button
Where the camera cable for ‘IK-TF9H’ is connected.
Used when switching the display.
1
2
3
4
5
6
PAGE button
Used when switching to the menu and when selecting the menus.
Select the function to be confirmed or changed on the menu.
Select the function to be confirmed or changed on the menu.
MENU UP button
MENU DOWN button
DATA UP (AWB) button
Changes the value of the function selected by the MENU (UP/DOWN)
button. (Also used when using AWB.)
DATA DOWN ABB button
Changes the value of the function selected by the MENU (UP/DOWN)
button. (Also used when using ABB)
7
DC IN 12V terminal
RGB terminal
Accept a DC power input (12V).
8
9
8-bit RGB, digital signal, and sync signal are output in the Camera
Link format.
Trigger signal is input.
Mode switching signal for partial scanning is input.
Accepts serial communication control signal.
Used to fix the camera.
Mounting holes M3
Mounting holes M2
Mounting holes M3
!
"
#
Used to fix the camera.
Used to fix the camera.
6
4. CONNECTION
4. 1 Standard Connection
Camera control unit
Lans
(option)
Cable
(option)
Camera cable
for IK-TF9U
IK-TF9U
(option)
Monitor
Frame grabber board,
image process
IK-TF9H
(option)
equipment etc.
DC IN 12V
DC power
supply (option)
4. 2 Cautions on Connection
• Only use optional camera head model # IK-TF9H with this camera controller.
The use of another head may cause damage to the control unit and camera head.
• When connecting the camera cables, be sure to turn off the camera control unit and any other equipment
connected to it.
• For DC power supply connecting to DC IN 12V terminal, use UL listed and/or CSA approved ungrounded
type AC adaptor with the specifications described below.
Power supply voltage
Current rating
Ripple voltage
Connector
: 12V DC 10%
: More than 830mA, Less than2.5A
: Less than 50mV(p–p)
: HR10A–7P–4S by HIROSE electronics Co. Ltd
Pins 1, 2 : 12V
Pins 3, 4 : GND
• If the securing screw on the connector of the camera cable loosens, noise may appear on the screen.
Be sure to tighten the connector completely.
• Use the standard cable for Camera Link.
4. 3 Connector Pin Assignments
DIGITAL
Function
I/O
–
DC IN 12V
1
2
3
4
5
6
7
8
9
GND
14
15
16
17
18
19
20
21
22
23
24
25
26
GND
X0+
1
2
3
4
+12V
X0-
O
O
O
O
O
I
+12V
GND
GND
X1-
X1+
13
26
1
X2-
X2+
Xcllk-
X3-
Xcllk+
X3+
14
SerTC+
SerTC-
Serial communication control (RXD)
Serial communication control (TXD)
Trigger pulse input
Partial scanning control
NC
1
2
4
3
O
I
SerTFG-
CC1-
SerTFG+
CC1+
CC2-
Connector used:
12226-51000-00
10 CC2+
CC3-
12 CC4+
GND
I
(3M) or equivalent.
CC3+
CC4-
11
–
Connector used:
–
NC
HR10A-7R-4PB
GND
13
–
(HIROSE electronics
Co. Ltd) or equivalent.
7
5. OPERATION
A camera head “IK-TF9H” is supposed to be connected to this camera control unit from this section.
Refer to the item " 4. CONNECTION", connect each equipment correctly.
Turn on the connected equipment and the power source of the camera.
1
2
3
When using the camera for the first time and when replacing the camera cable and the camera head, be
sure to operate the ABB adjustment refer to the item "Automatic Black Barance".
Aim the lens at the object, adjust the lens iris adjustment, focus adjustment, etc..
Refer to the item "5.1 White Balance", operate the adjustment.
4
5
6
Refer to the items "7. MODE SETTING BY ON SCREEN DISPLAY", select the necessary items.
5. 1 Automatic Black Balance
Black balance adjustment is necessary to get the correct black picture level.
• Close the lens iris.
• If the color bar pattern is displayed on the screen or if the index menu/menu is displayed, press the [DISP]
button to disable the color bar pattern or the character display.
• Hold the [DATA DOWN] button for approx. 1 second.
• When the black balance adjustment operation starts, the character ABB blinks on the screen.
• When the black balance adjustment operation finishes, the character ABB stops blinking and the result
appears for approx. 1 second.
• When the black balance adjustment performed, set the electronic shutter, Synchro. Scan, partial read to
OFF, and do not operate trigger mode or external sync.
Display
ABB OK
Meaning
Automatic black balance adjustment finished correctly.
ABB NG
CLOSE LENS
Automatic black balance adjustment cannot be performed because the
lens iris is open. Close the lens iris.
ABB NG
Automatic black balance adjustment cannot be performed.
Operate the automatic black balance again.
5. 2 White Balance
For the white balance adjustment for this unit, AWB (Automatic White Balance) and MANU (Manual white
balance) adjustments are provided. To select the desired mode, refer to the items "7.2 (3) WHT BAL (White
balance)" and "7. MODE SETTING BY ON SCREEN DISPLAY".
AWB
MANU
(Automatic White Balance)
(Manual White Balance)
Outline
Note
Adjust white balance by displaying the
white object inside the area set by AWB
menu and pressing the [DATA UP] button. white object.
Adjust the white balance manually using
the WHT BAL menu while shooting the
When the shutter mode is E.TRG, AWB is Adjustment is performed by confirming
not available.
with a monitor etc.
8
AWB (Automatic white balance)
1
• Set the MODE to AWB on the WHT BAL menu.
Perform the C.TEMP (color temperature conversion) setting, if necessary.
(Refer to the item "7.2 (3) WHT BAL (White balance)".)
3200K : Appropriate for indoor shooting.
5600K : Appropriate for outdoor shooting.
• If the index menu/menu is displayed, press the [DISP] button to disable the character display on the
menu.
• Shoot a known white object that fills the screen and push [DATA UP] button for approx. 1 second.
• The character AWB blinks on the screen when the AWB starts.
• The character AWB stops blinking when the AWB finishes, and the result is displayed for approx. 1
second.
Result displayed
Meaning
AWB OK
Automatic white balance adjustment finished correctly.
AWB NG LEVEL
LOW
Automatic white balance adjustment cannot be performed because the
video level is too low.
Obtain the proper video level.
AWB NG
LEVEL HIGH
Automatic white balance adjustment cannot be performed because the
video level is too high.
Obtain the proper video level.
AWB NG
C. TEMP LOW
Automatic white balance adjustment cannot be performed because the
color temperature is too low.
If the C.TEMP is set to 5600K, set to 3200K.
If the message appears with the C.TEMP set to 3200K, change the
illumination or use a color temperature conversion filter.
AWB NG
C. TEMP HIGH
Automatic white balance adjustment cannot be performed because the
color temperature is too high.
If the C.TEMP is set to 3200K, set to 5600K.
If the message appears with the C.TEMP set to 5600K, change the
illumination or use the color temperature conversion filter.
AWB NG
NOT AVAILABLE
Automatic white balance adjustment cannot be performed because the
shutter speed mode is E.TRG mode.
AWB NG
Automatic white balance adjustment cannot be performed for other
reasons. Such as no white area is included in an object, etc.
MANU (Manual white balance)
2
• Set the MODE to MANU on the WHT BAL menu.
(Refer to the item "7.2 (3) WHT BAL (white balance)".)
• Shoot a known white object, adjust the white balance adjusting the levels of R GAIN and B GAIN on the
menu, confirming with a monitor etc.
(Refer to the item "7.2 (3) (3.2) Changing each setting in MANU (Manual) mode".)
9
6. ITEMS CONTROLLED BY USING ON SCREEN DISPLAY
Preset value
(Factory setting)
Item
MODE
E. TRG
MANU speed
Available selections
MANU, SS, E. TRG
1P SNR, 1P SR, PW SNR, PW SR
OFF, 1/100s, 1/250s, 1/500s, 1/1000s, 1/2000s,
MANU
1P SNR
OFF
1/4000s, 1/10000s, 1/25000s, 1/50000s, 1/1000000s
Syncro. Partial read OFF 2H/1592H~1590H/1592H, OFF, 2FRM~512FRM
OFF
scan.
Partial read 25fps 2H/1270H~1268H/1270H, OFF, 2FRM~512FRM
Partial read 30fps 2H/1060H~1058H/1060H, OFF, 2FRM~512FRM
Partial read 35fps 2H/910H~908H/910H, OFF, 2FRM~512FRM
Partial read 40fps 2H/774H~772H/774H, OFF, 2FRM~512FRM
Partial read 45fps 2H/706H~704H/706H, OFF, 2FRM~512FRM
Partial read 50fps 2H/636H~634H/636H, OFF, 2FRM~512FRM
Partial read
OFF, 25fps, 30fps, 35fps, 40fps, 45fps, 50fps,
E25fps, E30fps, E35fps, E40fps, E45fps, E50fps
OFF
Trigger
(1P SNR/SR)
Trigger
(PW SNR/SR)
,
,
1P
50 ms
0.01ms~50ms
exposure time
MODE
MANU
MODE
Color temperature
MANUAL R GAIN
MANUAL B GAIN
GAMMA
Master pedestal
R pedestal
MANU, OFF
0dB~18dB
AWB, MANU
3200K, 5600K
-100~0~100
-100~0~100
ON, OFF
OFF
0dB
AWB
3200K
0
0
OFF
0
-64~0~64
-64~0~64
0
B pedestal
-64~0~64
0
Shading correction
mode
MANU, OFF
MANU
Manual shading
correction
H phase adjustment
-128~0~127
0
0
-100~0~100
Baud rate
9600 bps, 19200 bps
9600 bps
10
7. MODE SETTING BY ON SCREEN DISPLAY
Various settings can be controlled on the unit by using the on screen menu displayed on the monitor. The
contents once set are memorized even if the power source is turned off, so it is unnecessary to set again when
using the unit next time. When the setting is performed, select the menu of the item to be set.
7. 1 Using the Menus
When the power is turned on, the normal screen showing only the video signal appears. Change the output to
each screen (video signal output, Index menu, and menus) by using the [DISP], [PAGE], [MENU UP], and
[MENU DOWN] buttons.
* A menu is selected when pushing the [PAGE] button after moving the "→" on the screen by the [MENU UP],
[MENU DOWN] button while the Index menu is displayed.
POWER ON
Video signal output
Index menu
DISP
DISP
DISP
PAGE
PAGE
Menues
PAGE
WHT BAL
SHUTTER
GAIN
PROCESS
SYNC
INT
OPTION
SHAD.
MANU
BAUD
RATE
PAGE
PAGE
MANU
PAGE
AWB
PAGE
MANU
SS
PAGE
SHAD.
OFF
EXT
MANU
OFF
E. TRG
1P SR
E. TRG
1P SNR
E. TRG
PW SR
E. TRG
PW SNR
E. TRG
RR
11
7. 2 Menus
• Select the menu to change the setting by referring the item "7.1 Using the Menus".)
• When the [MENU UP], [MENU DOWN] buttons are pushed, the "→" on the screen moves up and down.
Move the "→" to the item to change.
Note:
When performing the mode setting in the menu display while selecting ON in "PART" (refer to page 29)
and E.TRG in "MODE", the display shows normal mode and then the camera returns the setting mode.
( 1 ) SHUTTER (Electronic shutter)
The electronic shutter has three modes; MANU (Manual), SS (Synchro. Scan), E.TRG (External trigger).
Set the "→" to "MODE" and push [DATA UP], [DATA DOWN] button to select the desired mode among "MANU",
"SS", "E.TRG".
MANUAL
:
It is possible to select the exposure time from eleven speed setting; OFF, 1/100s, 1/250s,
1/500s, 1/1000s, 1/2000s, 1/4000s, 1/10000s, 1/25000s, 1/50000s, 1/100000s.
Note:
When setting a rapid shutter speed, sensitivity degrades according to the speed.
When a discharging light such as fluorescent lamp, etc. is used for the illumination,
the flicker may be large.
SS
:
:
Shutter speed can be set by the double horizontal scanning time (2H) unit or by the frame
unit.
E.TRG
Exposure is performed and images are output by external trigger. E.TRG includes the four
modes described below. (For details of specifications, refer to the item “7.4 E.TRG
(External trigger)”.)
• 1P SNR (1 Pulse Sync Non Reset)
The charge begins to accumulate after the trigger pulse is received, and 1 frame images
are output according to the internal vertical sync signal timing. The exposure/accumula-
tion time can be set from 0.01 to 50 ms. The trigger signal timing can be set to either the
rising or falling edge.
• 1P SR (1 Pulse Sync Reset)
The charge begins to accumulate after the trigger pulse is received. Upon completion of
accumulation the vertical sync signal is reset and 1 frame images are output. The
exposure/accumulation time can be set from 0.01 to 50 ms. The trigger signal timing can
be set to either the rising or falling edge.
• PW SNR (Pulse width trigger Sync Non Reset)
The charge begins to accumulate after the trigger pulse is received, and 1 frame images
are output according to the internal vertical sync signal timing. This is the mode to set
the exposure period by the pulse width of the trigger. The trigger signal polarity can be
set to either the positive or negative polarity.
• PW SR (Pulse width trigger Sync Reset)
The charge begins to accumulate after the trigger pulse is received. Upon completion of
accumulation the vertical sync signal is reset and 1 frame images are output. This is the
mode to set the exposure period by the pulse width of the trigger. The trigger signal
polarity can be set to either the positive or negative polarity.
• RR (Reset restart)
Input of an external reset-restart signal permits one screen of information to be output
at an arbitrary timing.
12
(1. 1) Changing each setting in MANU mode
Move up down
Set by pushing
By pushing
MENU UP, DOWN
DATA UP, DOWN
• Sutter mode MANU, SS, E.TRG
-- SHUTTER --
• Sutter speed setting
OFF, 100 (1/100s), 250 (1/250s), 500 (1/500s)
1000 (1/1000s), 2000 (1/2000s), 4000 (1/4000s)
10000 (1/10000s), 25000 (1/25000s)
50000 (1/50000s)100000 (1/100000s)
MODE
MANU
PART
MANU
100
OFF
• Partial scanning switch
OFF/25fps/30fps/35fps/40fps/45fps/50fps/
E25fps/E30fps/E35fps/E40fps/E45fps/E50fps
<MODE = MANUAL>
(a) Changing the shutter speed
Set the "→" to MANU by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Set the shutter speed by pushing [DATA UP], [DATA DOWN] buttons.
(b) Partial scanning setting
Set the "→" to PART by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Select the mode by pushing [DATA UP], [DATA DOWN] buttons.
13
(1. 2) Changing each setting in SS (synchro. scan) mode
Move up down
Set by pushing
By pushing
MENU UP, DOWN
DATA UP, DOWN
• Sutter mode MANU, SS, E.TRG
-- SHUTTER --
• Synchro. scanning setting
OFF : 2H/1592H ∼ 1590H/1592H↔OFF↔2FRM↔512FRM
MODE
SS
PART
SS
OFF
OFF
30fps, E.30fps : 2H/1060H
∼
1058H/1060H↔OFF↔2FRM↔512FRM
40fps, E.40fps : 2H/774H↔772H/774H↔OFF↔2FRM↔512FRM
• Partial scanning switch
OFF/25fps/30fps/35fps/40fps/45fps/50fps/
E25fps/E30fps/E35fps/E40fps/E45fps/E50fps
<MODE = SS>
(a) Changing the shutter speed setting
Set the "→" to SS by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Select the shutter speed by pushing [DATA UP], [DATA DOWN] buttons.
(b) Partial scanning setting
Set the "→" to PART by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Select either the mode by pushing [DATA UP], [DATA DOWN] buttons.
Note:
The slow shutter speed may increase the fixed pattern noise and/or the white pixels. This is a charac-
teristic of CCD, and is not a symptom of malfunction.
14
(1. 3) Changing each setting in E.TRG mode
The E.TRG has five modes; 1P SNR, 1P SR, PW SNR, PW SR, PR.
First set the "→" to MODE and select E. TRG, then set the "→" to E.TRG and select the desired E.TRG mode.
(1. 3. 1) Changing each setting in 1P SNR mode
Move up down
Set by pushing
By pushing
MENU UP, DOWN
DATA UP, DOWN
• Sutter mode MANU, SS, E.TRG
-- SHUTTER --
• E.TRG mode
1P SNR, 1P SR, PW SNR, PW SR, RR
MODE
E.TRG
TRG.P
EXP.
PART
E.TRG
1P SNR
• Input trigger pulse setting at 1P SNR and 1P SR
Input trigger pulse : positive polarity
Input trigger pulse : negative polarity
50ms
OFF
• Exposure time setting at 1P SNR and 1P SR
0.01 ms
0.01 ms 0.02 ms
step step
• Partial scanning switch
OFF/25fps/30fps/35fps/40fps/45fps/50fps/
E25fps/E30fps/E35fps/E40fps/E45fps/E50fps
0.02 ms
0.4 ms
0.1 ms 1 ms
step step
1 ms
20 ms
2 ms
step
50 ms
<MODE = E.TRG E.TRG = 1P SNR>
(a) Changing the polarity of inputting trigger pulse setting
Set the "→" to TRG.P by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Select either
,
by pushing [DATA UP], [DATA DOWN] buttons.
(b) Changing 1P SNR exposure time setting
Set the "→" to EXP. by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Set the exposure time by pushing [DATA UP], [DATA DOWN] buttons.
(c) Changing the partial scanning setting
Set the "→" to PART by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Select the mode by pushing [DATA UP], [DATA DOWN] buttons.
15
(1. 3. 2) Changing each setting in 1P SR mode
Move up down
Set by pushing
By pushing
MENU UP, DOWN
DATA UP, DOWN
• Sutter mode MANU, SS, E.TRG, RR
-- SHUTTER --
• E.TRG mode
1P SNR, 1P SR, PW SNR, PW SR
MODE
E.TRG
TRG.P
EXP.
PART
E.TRG
1P SR
• Input trigger pulse setting at 1P SNR and 1P SR
Input trigger pulse : positive polarity
Input trigger pulse : negative polarity
50ms
OFF
• Exposure time setting at 1P SNR and 1P SR
0.01 ms
0.01 ms 0.02 ms
step step
• Partial scanning switch
OFF/25fps/30fps/35fps/40fps/45fps/50fps/
E25fps/E30fps/E35fps/E40fps/E45fps/E50fps
0.02 ms
0.4 ms
0.1 ms 1 ms
step step
1 ms
20 ms
2 ms
step
50 ms
<MODE = E.TRG E.TRG = 1P SR>
(a) Changing the polarity of inputting trigger pulse setting
Set the "→" to TRG.P by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Select either
,
by pushing [DATA UP], [DATA DOWN] buttons.
(b) Changing 1P SR exposure time setting
Set the "→" to EXP. by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Set the exposure time by pushing [DATA UP], [DATA DOWN] buttons.
(c) Changing the partial scanning setting
Set the "→" to PART by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Select the mode by pushing [DATA UP], [DATA DOWN] buttons.
16
(1. 3. 3) Changing each setting in PW SNR mode
Move up down
Set by pushing
By pushing
MENU UP, DOWN
DATA UP, DOWN
• Sutter mode MANU, SS, E.TRG
-- SHUTTER --
• E.TRG mode
MODE
E.TRG
PW SNR
1P SNR, 1P SR, PW SNR, PW SR, RR
E.TRG
TRG.P
PART
• Input trigger pulse setting at PW SNR and PW SR
Input trigger pulse : positive polarity
OFF
Input trigger pulse : negative polarity
• Partial scanning switch
OFF/25fps/30fps/35fps/40fps/45fps/50fps/
E25fps/E30fps/E35fps/E40fps/E45fps/E50fps
<MODE = E.TRG E.TRG = PW SNR>
(a) Changing the polarity of inputting trigger pulse setting
Set the "→" to TRG.P by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Select either
,
by pushing [DATA UP], [DATA DOWN] buttons.
(b) Changing the partial scanning setting
Set the "→" to PART by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Select the mode by pushing [DATA UP], [DATA DOWN] buttons.
Note:
The longer the storage time with extended exposures, the more visible certain characteristics of CCD
cameras become: fixed pattern noise, white pixels, etc.
17
(1. 3. 4) Changing each setting in PW SR mode
Move up down
Set by pushing
By pushing
MENU UP, DOWN
DATA UP, DOWN
• Sutter mode MANU, SS, E.TRG
-- SHUTTER --
• E.TRG mode
MODE
E.TRG
PW SR
1P SNR, 1P SR, PW SNR, PW SR, RR
E.TRG
TRG.P
PART
• Input trigger pulse setting at PW SNR and PW SR
OFF
Input trigger pulse : positive polarity
Input trigger pulse : negative polarity
• Partial scanning switch
OFF/25fps/30fps/35fps/40fps/45fps/50fps/
E25fps/E30fps/E35fps/E40fps/E45fps/E50fps
<MODE = E.TRG E.TRG = PW SR>
(a) Changing the polarity of inputting trigger pulse setting
Set the "→" to TRG.P by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Select either
,
by pushing [DATA UP], [DATA DOWN] buttons.
Note:
The longer the storage time with extended exposures, the more visible certain characteristics of CCD
cameras become: fixed pattern noise, white pixels, etc.
(1. 3. 5) Changing each setting in RR mode
Move up down
Set by pushing
By pushing
MENU UP, DOWN
DATA UP, DOWN
• Shutter mode MANU, SS, E.TRG
-- SHUTTER --
• E.TRG mode
MODE
E.TRG
PART
E.TRG
RR
OFF
1P SNR, 1P SR, PW SNR, PW SR, RR
• Partial scanning switch
OFF/25fps/30fps/35fps/40fps/45fps/50fps/
E25fps/E30fps/E35fps/E40fps/E45fps/E50fps
<MODE = E.TRG E.TRG = RR>
(a) Changing the partial scanning setting
Set the "→" to PART by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Select the mode by pushing [DATA UP], [DATA DOWN] buttons.
Note:
The longer the storage time with extended exposures, the more visible certain characteristics of CCD
cameras become: fixed pattern noise, white pixels, etc.
18
( 2 ) GAIN (Video gain)
When the image is dark even if the lens iris is open, change the gain (video gain) to get the proper video level.
For the gain adjustment of the unit, MANU (Manual) and OFF (0dB) modes are provided.
1 MANU (Manual gain)
Gain adjustment is performed on the GAIN menu. The adjustment range is from 0dB to 18dB in 1dB steps.
2 OFF
Gain is fixed at 0dB.
Set the "→" to MODE, push the [DATA UP], [DATA DOWN], and select mode among MANU, OFF.
(2. 1) Changing each setting in GAIN
Move up down
Set by pushing
By pushing
MENU UP, DOWN
DATA UP, DOWN
-- GAIN --
MODE
MANU
MANU
0dB
• Gain mode MANU, OFF
• Manual gain 0 dB to 18 dB (10 dB step)
(a) Changing the gain in MANU mode
Set the "→" to MANU by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Set the manual gain by pushing [DATA UP], [DATA DOWN] buttons.
19
( 3 ) WHT BAL (White balance)
WHT BAL has two modes; AWB, MANU.
Set the "→" to MODE, push the [DATA UP], [DATA DOWN], and select mode among AWB, MANU.
(3. 1) Changing each setting in AWB (Automatic White Balance) mode
Move up down
Set by pushing
By pushing
MENU UP, DOWN
DATA UP, DOWN
-- WHT BAL --
MODE
AWB
• White balance mode setting (AWB, MANU)
R GAIN
B GAIN
C.TEMP
0
0
Automatically adjusting value for red gain and blue gain
are shown on the screen
* These values may not be changed during AWB mode.
3200
• Color temperature setting 3200, 5600
(a) Changing color temperature setting
Set the "→" to C.TEMP by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Select either 3200 or 5600 by pushing [DATA UP], [DATA DOWN] buttons.
(3. 2) Changing each setting in MANU (Manual) mode
Move up down
Set by pushing
By pushing
MENU UP, DOWN
DATA UP, DOWN
-- WHT BAL --
MODE
MANU
• White balance mode AWB, MANU
• Red gain adjustment -100 to 100
• Blue gain adjustment -100 to 100
• Color temperature setting 3200, 5600
R GAIN
B GAIN
C. TEMP
0
0
3200
(a) Changing the red gain
Set the "→" to R GAIN by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Set the red gain by pushing [DATA UP], [DATA DOWN] buttons.
(b) Changing the blue gain
Set the "→" to B GAIN by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Set the blue gain by pushing [DATA UP], [DATA DOWN] buttons.
20
( 4 ) PROCESS
• Gamma Correction (GAMMA)
Select either OFF or ON of Gamma Correction.
• Master Pedestal (M. PED)
Set the Pedestal level of each RGB.
• R Pedestal (R. PED)
Set the Pedestal level of Red.
• B Pedestal (B. PED)
Set the Pedestal level of Blue.
• Shading Correction (SHAD.)
Due to the lens used or the environmental condition, vertical color shading may occur at the top and bottom
of the screen. In this case, the shading correction can decrease the color shading. For the shading correction
of the unit, MANU (Manual shading correction) and OFF (no shading correction) modes are provided.
MANU (Manual Shading)
1
Adjust the correction amount on the PROCESS menu by confirming with a monitor or a waveform monitor.
OFF
2
The status is no shading correction.
* The shading correction is effective when the lens iris or zoom ratio is fixed. Use the unit with
SHAD. OFF for variable lens conditions.
Move up down
Set by pushing
By pushing
MENU UP, DOWN
DATA UP, DOWN
• Gamma correction ON/OFF
-- PROCESS --
• Master pedestal adjustment -64 to 64
• R pedestal adjustment -64 to 64
GAMMA
M.PED
R.PED
B.PED
SHAD.
MANU
OFF
0
0
0
MANU
0
• B pedestal adjustment -64 to 64
• Shading mode setting MANU/OFF
• Manual shading adjustment -128 to 127
(4. 1) Changing gamma correction
Set the "→" to GAMMA by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Set the gamma correction by pushing [DATA UP], [DATA DOWN] buttons.
(4. 2) Changing master pedestal
Set the "→" to M. PED by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Set the master pedestal by pushing [DATA UP], [DATA DOWN] buttons.
(4. 3) Changing R pedestal
Set the "→" to R. PED by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Set the R pedestal by pushing [DATA UP], [DATA DOWN] buttons.
(4. 4) Changing B pedestal
Set the "→" to B. PED by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Set the B pedestal by pushing [DATA UP], [DATA DOWN] buttons.
21
(4. 5) Changing the shading correction mode
Set the "→" to SHAD. by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Set the SHAD. by pushing [DATA UP], [DATA DOWN] buttons.
Note: The alignment value for shading is fixed to "0" when selecting SHAD. OFF. MANU is not dis-
played in the menu.
(4. 6) Changing the manual shading correction setting
Set the "→" to MANU by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Set the MANUAL SHADING by pushing [DATA UP], [DATA DOWN] buttons.
( 5 ) SYNC
When an external sync signal is input, the display menu changes from INT (internal sync) to EXT (external
sync) automatically.
Move up down
Set by pushing
By pushing
MENU UP, DOWN
DATA UP, DOWN
-- SYNC --
MODE
H PHASE
EXT
0
• Sync system display
• H PHASE -100 to 100
(5. 1) Adjusting horizontal phase
Set the "→" to H PHASE by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Adjust the horizontal phase by pushing [DATA UP], [DATA DOWN] buttons.
( 6 ) OPTION
(6. 1) Changing serial communication baud rate
Set the "→" to BAUD RATE by pushing [MENU UP], [MENU DOWN] buttons.
1
2
Select either 9600 or 19200 by pushing [DATA UP], [DATA DOWN] buttons.
Move up down
By pushing
MENU UP, DOWN
Set by pushing
DATA UP, DOWN
-- OPTION --
BAUD RATE
9600
• Serial baud rate 9600, 19200
22
( 7 ) Setting to factory setting status
All the settings can be returned to the factory default status (preset status).
(1) If characters are displayed on the screen, press the [DISP] button to disable the character display.
(2) Push [MENU DOWN] and [DATA DOWN] buttons simultaneously for approx. 1 second.
(3) The preset operation starts. When the preset operation finishes, the character PRESET OK is displayed
for approx. 1 second.
7. 3 Synchro. Scan Operation
The shutter speed can be set by the double horizontal scanning period (2H) or by the frame.
( 1 ) Setting by 2H
2H/1592H ~ 1590H/1592H stands for the setting by the 2H and the shutter speed can be set by the 2H (62.8
µs).
When operating Partial Scannig, the number’s listed below can be used for setting.
25fps, E25fps
30fps, E30fps
35fps, E35fps
40fps, E40fps
45fps, E45fps
50fps, E50fps
2H/1270H ~ 1268H/1270H
2H/1060H ~ 1058H/1060H
2H/910H ~ 908H/910H
2H/774H ~ 772H/774H
2H/706H ~ 704H/706H
2H/636H ~ 634H/636H
( 2 ) Setting by the frame
2FRM to 512FRM stand for the setting (long period exposure) by the frame.
The video signal stored during the frame period set is output as 1 frame video image at a frame interval
specified.
(Internal VD)
n
n+1
RGB data
(video interval image)
FVAL
LVAL,
DAVL
(4FRM setting)
23
7. 4 E. TRG (External trigger)
Charge begins to accumulate after the trigger input to CC1 of the DIGITAL terminal, and 1 frame images are
output. There are four modes: 1P SNR, 1P SR, PW SNR, PW SR.
( 1 ) 1P SNR (1 Pulse Trigger Sync Non Reset)
Charge begins to accumulate after the trigger input to CC1 of the DIGITAL terminal, and 1 frame images are
output.
(1. 1) 1 Pulse Trigger SYNC-NON RESET Picture Output Timing
Negative polarity mode
Trigger*1
Positive polarity mode
About 1 µs
Exposure period*2
Exposure period*2
3
(Internal VD)
RGB data
*
(video interval image)
FVAL
LVAL,
DVAL
58H (Partial scanning OFF
)
40H (Partial scanning 25fps)
56H (Partial scanning 30fps)
66H (Partial scanning 35fps)
78H (Partial scanning 40fps)
80H (Partial scanning 45fps)
86H (Partial scanning 50fps)
*1: Externally input signal
*2: Exposure time is determined by the setting of "7. 2 (1.3) Changing each setting in E.TRG mode".
*3: Video is output at the falling edge of the internal VD following completion of the exposure period.
The video and FVAL/LVAL/DVAL have a paired relationship.
Note:
When the next trigger is input before completion of the output of the video corresponding to the trig-
ger, there will be an effect on the video.
24
( 2 ) 1P SR (1 Pulse Trigger Sync Reset)
Charge begins to accumulate after the trigger input to CC1 of the DIGITAL terminal, the vertical sync signal is
reset and frame images are output.
(2. 1) 1 Pulse Trigger SYNC-RESET Picture Output Timing
Negative polarity mode
Trigger*1
Positive polarity mode
About 1 µs
Exposure period*2
Exposure completion
0 to 2H*3
(Internal VD)
RGB data
(video interval image)
FVAL
LVAL,
DVAL
58H (Partial scanning OFF
)
40H (Partial scanning 25fps)
56H (Partial scanning 30fps)
66H (Partial scanning 35fps)
78H (Partial scanning 40fps)
80H (Partial scanning 45fps)
86H (Partial scanning 50fps)
*1: Externally input signal
*2: Exposure time is determined by the setting of "7. 2 (1.3) Changing each setting in E.TRG mode".
*3: VD is generated after 0 to 2H following the completion of the exposure period and the video is synchro-
nized to this and output.
Note:
When the next trigger is input before completion of the output of the video corresponding to the trig-
ger, there will be an effect on the video.
25
( 3 ) PW SNR (Pulse width trigger SYNC-NON RESET)
The trigger input to CC1 of the DIGITAL terminal develops 1 frame images.
(3. 1) Pulse Width Trigger SYNC-NON RESET Picture Output Timing
Negative polarity mode
Positive polarity mode
Trigger*1
About 1 µs
About 7 µs
Exposure period*2
Exposure period*2
(Internal VD)
RGB data
(video interval image)
FVAL
LVAL,
DVAL
58H (Partial scanning OFF
)
The internal VD falling edge is within the
exposure period and thus video is not output.*3
40H (Partial scanning 25fps)
56H (Partial scanning 30fps)
66H (Partial scanning 35fps)
78H (Partial scanning 40fps)
80H (Partial scanning 45fps)
86H (Partial scanning 50fps)
*1: Externally input signal
*2: Exposure time = Trigger pulse width + 6 µs
(Valid trigger pulse width is 2 µs or greater for external trigger shutter operation.)
*3: Video is output at the falling edge of the internal VD following completion of the exposure period.
The video and FVAL/LVAL/DVAL have a paired relationship.
Note:
When the next trigger is input before completion of the output of the video corresponding to the trig-
ger, there will be an effect on the video.
26
( 4 ) PW SR (Pulse width trigger SYNC-RESET)
The trigger input to the CC1 of the DIGITAL terminal develops 1 frame images.
(4. 1) 1 Pulse Width Trigger SYNC-RESET Picture Output Timing
Negative polarity mode
Positive polarity mode
Trigger*1
About 1 µs
About 7 µs
Exposure period*2
Exposure completion
0 to 2H
3
(Internal VD)
*
RGB data
(video interval image)
FVAL
LVAL,
DVAL
58H (Partial scanning OFF
)
40H (Partial scanning 25fps)
56H (Partial scanning 30fps)
66H (Partial scanning 35fps)
78H (Partial scanning 40fps)
80H (Partial scanning 45fps)
86H (Partial scanning 50fps)
*1: Externally input signal
*2: Exposure time = Trigger pulse width + 6 µs
(Valid trigger pulse width is 2 µs or greater for external trigger shutter operation.)
*3: VD is generated after 0 to 2H following the completion of the exposure period and the video is synchro-
nized to this and output.
Note:
When the next trigger is input before completion of the output of the video corresponding to the trig-
ger, there will be an effect on the video.
27
( 5 ) RR (Reset restart)
Input of an external reset-restart signal (CC4 of the DIGITAL terminal: External VD input) permits one screen
of information to be output at an arbitrary timing.
(5. 1) Long Term Exposure
When a sufficient sensitivity is not obtained with the normal operation conditions or capturing the trial of a
moving subject is desired, the reset-restart function allows high-sensitivity images by extending the exposure
time. To achieve this, please input from an external source a VD signal that has an expanded VD pulse and VD
pulse interval.
(5. 2) Input Timing Chart Example
External HD IN
External VD IN
V reset
V reset
About 1H
About 1H
(Internal VD)
Exposure period
Exposure period
Exposure period
RGB data
(video interval image)
FVAL
LVAL,
DVAL
1 frame
1 frame= 1592H (Partial scanning OFF
)
1270H (Partial scanning 25fps)
1060H (Partial scanning 30fps)
910H (Partial scanning 35fps)
774H (Partial scanning 40fps)
706H (Partial scanning 45fps)
636H (Partial scanning 50fps)
External VD interval: more than 1 frame
28
7. 5 Partial Read
( 1 ) Partial Scanning OFF (All pixels scanning)
In this mode, all pixels independent signal from the DIGITAL connector is output each 1/20 second (Line order
output).
Video interval
image
1/20s (1592H)
( 2 ) Partial Scanning ON
In this mode, the pixel signal of the vertical center portion from the DIGITAL connector is output.
In the E.✽✽fps mode, the partial scanning and the all pixels scanning can be switched by the DIGITAL terminal
(CC2: partial scanning control signal).
CC2
E.25fps
E.30fps
E.35fps
E.40fps
E.45fps
E.50fps
‘L’ Partial scanning 25fps Partial scanning 30fps Partial scanning 35fps Partial scanning 40fps Partial scanning 45fps Partial scanning 50fps
‘H’ All pixels scanning All pixels scanning All pixels scanning All pixels scanning All pixels scanning All pixels scanning
Video interval
image
1/25s (1270H): When 25fps is selected
1/30s (1060H): When 30fps is selected
1/35s (910H): When 35fps is selected
1/40s (774H): When 40fps is selected
1/45s (706H): When 45fps is selected
1/50s (636H): When 50fps is selected
( 3 ) When Partial Scanning Mode is ON
(Internal VD)
FVAL
LVAL,
DVAL
RGB data
(video interval image)
Blanking interval
Video interval Blanking interval
B
C
D
Total
A
Video period
Mode
25fps
30fps
35fps
40fps
45fps
50fps
Total A
1270H
1060H
910H
Blanking interval B Video interval C Blanking interval D
40H
56H
66H
78H
80H
86H
1024H
972H
792H
644H
564H
480H
26H
32H
52H
52H
62H
70H
774H
706H
29
636H
7. 6 External Sync
When using the unit with an external sync signal, input HD and VD to CC3 and CC4 of the DIGITAL terminal.
When the external sync signal is input, the camera automatically switches its sync from the internal sync to the
external sync.
The operation is as shown below, depending on the unit's status and how external sync signals are input.
Shutter mode
At time of SYNC-NON
RESET mode
HD input VD input
Note
N
Y
N
Y
N
Y
Y
N
Internal sync mode
External sync mode
Only V reset is applied due to VD input. Normally not used.
HD is synchronized to external, but video is not output
because there is no VD input. Normally not used.
At time of SYNC-RESET
mode
N
Y
*
*
Internal sync mode. The presence of VD is ignored, and after
a specified time after a trigger input, V reset is applied.
HD is synchronized to external. The presence of VD is
ignored, and after a specified time after a trigger input, V
reset is applied.
At time of reset restart
Y
N
*
Y
Y
N
HD is synchronized to external. Video is output due to VD
input.
HD is synchronized to the inside of the camera. Video is
output due to VD input.
Video is not output because there is no VD input. Normally
not used.
At time of manual
shutter
N
Y
Y
N
N
Y
N
Y
Internal sync mode
External sync mode
HD is synchronized to external. Normally not used.
Disabled
* Either Y or N is permitted.
( 1 ) External sync signal polarity
HD: 2 to 5V(p-p) Negative
VD: 2 to 5V(p-p) Negative
( 2 ) External sync frequency range
(External sync with HD, VD)
Within 1% (at horizontal sync frequency of 31.84 kHz)
( 3 ) Using the unit with external sync signal
When adjusting H (horizontal) phase refer to the item "7.2 (5) (5.1) Adjusting horizontal phase".
(3. 1) H (horizontal) phase adjustment
External
Sync. signal
Observe the external sync signal and the LVAL signal output
Match
waveform of the unit with a dual trace oscilloscope, and ad-
the phase.
just H phase so that the H phases match.
LVAL signal
output
30
8. OUTPUT WAVEFORM TIMING CHART
( 1 ) Horizontal Output Waveform Timing Chart
One horizontal scan interval 2540 clk
(31.4 µs)
LVAL、
DVAL
Horizontal blanking interval 492 clk
Output video interval 2048 clk
(25.3 µs)
(6.08 µs)
RGB data
Pixel
Clock
CLK=12.36nsec
(80.8736MHz)
( 2 ) Vertical Output Waveform Timing Chart
1592H
FVAL
56H
（1759μs）
LVAL、
DVAL
(CCD READOUT)
Video output
Vertical blanking
interval 56H
RGB data
Vertical blanking
interval 56H
1536H
（1759μs）
（1759μs）
31
9. SPECIFICATIONS
Power supply
12V DC 10%
Power consumption
Pick-up system
Image sensor
Approx. 5.4W
RGB, 3CCD
1/3inch All pixels CCD
(Effective pixels Horizontal : 1034, Vertical : 779)
Scanning System
Video output pixels
Pixel clock frequency
Sync signal frequency
Sync system
Progressive scan
Horizontal pixels : 2048, Vertical : 1536
80.8736MHz
Horizotal : 31.84KHz, Vertical : 20Hz
Internal
Sensitivity
F8 standard (2000 lx, 3000K)
10 lx (F2.2, Sensitivity + 18 dB, 3000K)
C mount (flange back : 17.526 mm in-air)
32 to 104°F (0 to 40°C)
Minimum illumination
Lens mount
Ambient temperature
Ambient humidity
Weight
Less than 90%
Approx. 0.353lbs (160g)
External dimension
1.73” (W) x 1.73” (H) x 3.07” (D)
(44 (W) x 44 (H) x 78 (D) mm)
(except for protruded portion)
White balance
Gain
AWB (Automatic white balance), MANUAL (Manual)
MANUAL (Manual), OFF (0 dB)
Partial scanning
Output signal
Sync signal output
25fps, 30fps, 35fps, 40fps, 45fps, 50fps
8-bit RGB, Digital output (Camera Link format)
FVAL, LVAL, DVAL (Positive polarity)
Pixel Clock
External trigger input
CC1 (LVDS input), More than 2 µs pulse width
Partial scanning control CC2 (LVDS input)
signal input
Interface
Serial data interface : Ser TC (RXD), Ser TFG (TXD)
IK-TF9H (CAMERA HEAD) EXC-CL05S (Cable), etc
Optional parts
The designs and specifications are subject to change without notice.
32
10. EXTERNAL APPEARANCE DIAGRAM
Unit : inch [mm]
0.19 [4.8]
0.25
[6.3]
0.21
[5.3]
1.73 [44]
78 [3.07]
0.47 [12]
0.19 [4.8]
2-M2
0.18 [4.5]
2.20 [56]
4-M3 Depth 3
0.76
[19.2]
* inch = mm/25.4
4-M2 Depth 3
0.96
[24.5]
0.98
[25]
11. BEFORE MAKING A SERVICE CALL
Symptom
Items to be checked
No image
• Is the power supplied correctly?
• Is the lens iris adjusted correctly?
• Are the cables connected correctly?
• Is the shutter mode set correctly?
• Is the image process equipment set correctly?
Poor color
• Is the monitor adjusted correctly?
• Is the white balance of the camera adjusted correctly?
• Is the illumination dark?
33
Limited Warranty – TOSHIBA CCD Camera
The Imaging Systems Division of Toshiba America Information Systems, Inc. ("ISD") makes the following limited warranties
with regard to this CCD Camera ("Product"). These limited warranties extend to the Original End-User ("You[r]").
One (1)Year Limited Warranty of Labor and Parts
ISD warrants that this Product will perform in accordance with specifications for a period of one (1) year from the date of
purchase by the Original End-User. During this one (1) year period, ISD will repair or replace the Product, if it does not
perform as warranted. In order to take advantage of this Limited Warranty, You must: (a) deliver the Product to an ISD
Authorized Service Provider ("ASP"); and (b) pay all transportation and insurance charges for shipment of the Product to the
ASP. ISD reserves the right to substitute factory refurbished parts in place of those in need of repair.
Instruction Manual (Owner’s Manual):
You should read the Instruction Manual (Owner’s Manual) thoroughly before operating this Product. Before seeking warranty
service, you should check the troubleshooting guide in the Instruction Manual (Owner’s Manual) and follow the instructions to
correct the problem.
Your Responsibilities
This Limited Warranty is subject to the following conditions:
1. You must provide the bill of sale or proof of purchase at the time that warranty service is required.
2. You must notify an ASP within thirty (30) days after You discover that the Product does not perform in accordance with
specifications during the Limited Warranty period.
3. All warranty servicing of this product must be made by an ISD Authorized Service Provider.
4. You must pack the Product in its original carton using the original packing material, then insert the original carton
containing the Product into another carton with additional packing material before shipping the Product to an ASP.
DISCLAIMERS:
ALL OTHER EXPRESS OR IMPLIED WARRANTIES ON THIS PRODUCT, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED. SOME STATES DO
NOT ALLOWTHE EXCLUSION OF IMPLIED WARRANTIES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TOYOU.
IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTED ABOVE, YOUR SOLE AND EXCLUSIVE
REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF THE PRODUCT. IN NO EVENT WILL ISD OR ITS PARENT
COMPANY OR ANY ASP BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY DAMAGES IN EXCESS OF THE
PURCHASE PRICE OF THE PRODUCT. THIS LIMITATION APPLIES TO DAMAGES OF ANY KIND, INCLUDING ANY
DIRECT OR INDIRECT DAMAGES, LOST PROFITS, LOST SAVINGS OR OTHER SPECIAL, INCIDENTAL, EXEMPLARY
OR CONSEQUENTIAL DAMAGES, WHETHER FOR BREACH OF CONTRACT, TORT OR OTHERWISE, OR WHETHER
ARISING OUT OF THE USE OF OR INABILITY TO USE SUCH PRODUCT, EVEN IF TAIS, ITS PARENT COMPANY, OR
AN ASP HAS BEEN ADVISED OFTHE POSSIBILITY OF SUCH DAMAGES OR OF ANY CLAIM BY ANY OTHER PARTY.
SOME STATES DO NOT ALLOWTHE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES
FOR SOME PRODUCTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TOYOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY
VARY FROM STATE TO STATE.
THIS LIMITED WARRANTY SHALL BE VOID IF THE PRODUCT OR PARTS HAVE BEEN SUBJECTED TO MISUSE,
ABUSE, ACCIDENT, IMPROPER INSTALLATION, IMPROPER MAINTENANCE, OR USE IN VIOLATION OF ISD’S
WRITTEN INSTRUCTIONS, OR WHERE THE PRODUCT HAS BEEN ALTERED OR MODIFIED WITHOUT ISD’S PRIOR
AUTHORIZATION, OR UPON THE REMOVAL OR ALTERATION OF ISD’S FACTORY SERIAL NUMBER. LABOR
SERVICE CHARGES FOR PRODUCT INSTALLATION, SET UP AND ADJUSTMENT OF CONTROLS ARE NOT
COVERED BY THIS LIMITED WARRANTY.
How to Obtain Warranty Service – Step-By-Step Procedures:
To obtain warranty service, You should:
1. Contact an ASP for warranty service within thirty (30) days after the Product fails to comply with specifications.
2. Arrange for shipment of the Product to an ASP.
3. Securely pack the Product as described above, insure the carton, and include a letter explaining the problem and a copy
of the bill of sale or proof of purchase.
4. Prepay all transportation and insurance costs.
Questions? If you have any questions, please check ISD’s Web Site or send an e-mail as follows:
E-mail: [email protected]
No person, agent, distributor, dealer, authorized service provider, or company is authorized to change, modify, or extend the
terms of this Limited Warranty in any manner whatsoever. The time within which an action must be commenced to enforce
any obligation of ISD arising under this Limited Warranty or under any statute, or law of the United States or any state thereof,
is hereby limited to one (1) year from the date You discover or should have discovered the problem. This limitation does not
apply to implied warranties arising under state law. Some states do not permit limitation of the time within whichYou may bring
an action beyond the limits provided by state law, so the above provision may not apply to You. This Limited Warranty gives
You specific legal rights and You may also have other rights which vary from state to state.
TOSHIBA AMERICA INFORMATION SYSTEMS, INC.
Imaging Systems Division
9740 Irvine Boulevard, Irvine, CA 92618-1697
Copyright© 2007 Toshiba America, Inc. All rights resered.
|