Turbo air Speeds Up the Pace of Innovation
CAUTION!
PLEASE KEEP POWER SWITCH ON
BEFORE OPERATING THIS EQUIPMENT
Refrigerator
Freezer
Installation and Operation Manual
Please read this manual completely before attempting to install or operate this equipment!
<Solid Door>
Refrigerator
MSR-23NM
MSR-49NM
Freezer
MSF-23NM
MSF-49NM
<Glass Door>
Refrigerator
MSR-23G-1
MSR-49G-2
MSR-72G-3
INSTALLATION
1. GOOD AIR CIRCULATION
- Be sure to avoid any partition and object which may stop the air flow.
- Be sure that air space is allowed to flow the rear of the unit.
Turbo air recommends that the rear of the unit would be no less than 5 inches from the
wall.
2. PLACE ON STRONG GROUND
- Be sure that the location be chosen has a strong enough floor to support the total
weight of the cabinet and any other contents.
3. DO NOT PLACE NEAR HEAT
- Be sure to avoid hot corners and locations near stoves.
- High ambient temperature will make much lower cooling efficiency.
4. INDOOR USAGE ONLY
- Be sure to install this unit indoor.
- So, It should prohibit getting wet from the rain.
5. STABILIZING
- Make sure the unit is installed in a stable condition with the front wheels locked
while in use.
6. LEVELING
- Be sure that the unit levels from the front to the back and side to side.
7. Unit should be on dedicated outlet.
8. Place black plastic condensate pan through back or front.
Make sure pads are installed upwards, a drain hose is in pan.
3
Turbo air
CLEANING
1. CLEANING STAINLESS STEEL INTERIOR AND EXTERIOR (select models)
: Damage to stainless steel finish due to improper use of cleaning products or non-
recommended products is NOT covered under this product's warranty.
• DO NOT USE
- Abrasive or harsh cleaners
- Ammonia
- Chlorine bleach
- Concentrated detergents or solvents
- Metal or plastic-textured scouring pads
- Vinegar-based products
- Citrus-based cleaners
• Do
- Use warm, soapy water and a soft, clean cloth or sponge.
- Rinse surfaces with clean, warm water and dry immediately to avoid water spots.
2. CLEANING THE CONDENSER FINS
- To maintain proper refrigeration performance, the Condenser coil must be free of
dust, dirt, and grease.
This will require periodic cleaning. Condenser fins should be cleaned at least every
three months (90 days) or as needed.
3. CLEAN THE GASKET
- The door gasket should be cleaned frequently to maintain proper sealing.
4. CHECK AFTER CLEANING
- Check the unit again for safety.
- Check that the unit is operating properly.
CAUTION
1. POWER CORD
- Be sure that the power cord is connected to the proper voltage.
- A protected circuit of the correct voltage and amperage must be run for connection of
the line cord.
- Turn ‘off’ the power switch before disconnecting the power cord, whenever
performing maintenance functions or cleaning the refrigerated cabinet.
- Compressor warranties are void if compressor burns out due to low voltage.
2. RE-STARTING
- If disconnected, wait for 5 minutes before re-starting.
4
Turbo air
BASIC OPERATION
MSR-23NM MSR-23G-1
MSR-49NM MSR-49G-2
MSR-72G-3
REFRIGERATORS
1. Plug in and turn on the power switch located on the bottom of the top grille right side.
The Display panel will be lighted and make a beep sound. The compressor will begin
to run.
2. The default temperature setting is No. “5”.
3. The compressor is automatically cycled by the electronic controller (PCB, D-Sensor).
4. The Defrost cycle is automatically controlled by the R-sensor, and the PCB.
5. Set level toward “1” for higher temperature and toward “9” for lower temperature.
6. The interior light is activated by the rocker switch at the bottom of the grille when the
door is opened. (MSR-23NM,MSR-49NM)
7. Evaporator fan motor(s) will run after all doors are completely closed.
5
Turbo air
DISPLAY PANEL OF REFRIGERATOR
TEMP. SETTING
TEMP. CONTROL BUTTON
(SEE TO PAGE 7)
INNER TEMP.
(SEE TO PAGE 8)
1
2
3
4
5
TEMPERATURE
˚F
6
7
8
9
TEMPERATURE
Q.C.
FAN
DOOR
QUICK COOLING
QUICK COOLING
QUICK COOLING
BUTTON
(SEE TO PAGE 7)
FAN RUNNING
DOOR OPENING
6
Turbo air
QUICK COOLING
1. If you push the Q.C. (QUICK Cooling) button, the compressor will run continuously
until D-Senser detect 14˚F (-10˚C) to bring down the temperature more quickly.
(max.comp.run time = 120 min.)
2. If you push the Q.C. button again during QUICK Cooling mode, the compressor will
return to the normal operation.
3. During the QUICK Cooling mode works, the temperature Up/Down button will not
affect the compressor’s operation.
UP/DOWN BUTTON (Temperature control button)
1. By pushing the up/down button, you can set the inside temperature level from ‘1’ to
‘9’.
2. If you want lower temperature, push the Down button to be lighted higher level
numbers.
7
Turbo air
INNER TEMPERATURE DISPLAY
1. It displays the inside temperature.
2. Display range is 14˚F to 69˚F (-10˚C ~ +20˚C).
3. When the inside temperature is lower than 14˚F, the panel will display ‘
’.
and, higher than 69˚F, the panel will display ‘
’.
FAN RUNNING INDICATOR
1. If the fan motor is running, fan running indicator will be turned on.
2. Evaporator fan motor is activated when the door is closed.
DOOR OPENING INDICATOR
1. If any door is opened, door opening indicator will be turned on.
2. In case that any door was opened around 30 seconds, warning beep sound will ring
three (3) times.
3. In case of passing around 1 minute, warning beep sound will ring again five (5) times.
4. In case of passing around 5 minutes, the beep sound will ring continuously.
5. The beep sound will stop immediately if door is closed properly.
8
Turbo air
BASIC OPERATION
MSF-23NM
MSF-49NM
FREEZERS
1. Plug in and turn on the power switch located on the bottom of the top grille right side.
The Display panel will be lighted and make a beep sound. The compressor will begin
to run.
2. The default temperature setting is No. “5”.
3. The compressor is automatically cycled by the electronic controller (PCB, F-Sensor).
4. The Defrost cycle is automatically controlled by the D-sensor, and the PCB.
5. Set level toward “1” for higher temperatures and toward “9” for lower temperatures.
6. The interior light is activated by the rocker switch at the bottom of the grille when the
door is opened.
7. Evaporator fan motor(s) will run after all doors are completely closed.
8. Good Air Flow in freezer unit is critical.
Be careful to load product so that it neither presses against the back wall, nor reaches
within four inches from the evaporator compartment.
9
Turbo air
DISPLAY PANEL OF FREEZER
TEMP. SETTING
TEMP. CONTROL BUTTON
(SEE TO PAGE 11)
INNER TEMP.
(SEE TO PAGE 12)
1
2
3
4
5
TEMPERATURE
˚F
6
7
8
9
TEMPERATURE
D.F.
FAN
DOOR
MANUAL DEFROST
MANUAL DEFROST
MANUAL DEFROST
BUTTON
(SEE TO PAGE 11)
FAN RUNNING
DOOR OPENING
10
Turbo air
MANUAL DEFROST
1. If you push MANUAL DEFROST button for 5 seconds, the Defrost will start.
2. During the Manual Defrost mode, the Up/Down button for the temperature control
can not make the compressor cycle ON or OFF.
3. If you want to change the Manual Defrost mode to the normal mode, push MANUAL
DEFROST button for 5 seconds.
UP/DOWN BUTTON (Temperature control button)
1. By pushing the up/down button, you can set the inside temperature level from ‘1’ to
‘9’.
2. If you want lower temperatures, push the Down button to be lighted higher level
numbers.
DEFROST
1. The electronic defrost controller is set at the factory to provide a defrost cycle every 6
hours (4 times per a day).
2. If it is necessary to change the intervals of defrost due to unusual operating
conditions, it can be accomplished by adjusting the switch which is located on the
inside of the top grille.
3. Once all frost is eliminated, the temperature continues to rise until it reaches 60˚F
(15˚C). When this temperature is sensed by the defrost limit control, the defrost
control changes to refrigeration mode.
4. The panel displays “
” during the defrost cycle.
11
Turbo air
INNER TEMPERATURE DISPLAY
1. It displays inside temperature.
2. Display range is -50˚F to 50˚F (-45˚C ~ +10˚C).
3. When inside temperature is lower than -50˚F, the panel will display ‘
’.
and, higher than +50˚F, the panel will show ‘
’.
FAN RUNNING INDICATOR
1. If the fan motor is running, fan running indicator will be turned on.
2. Evaporator fan motor is activated when the door is closed.
DOOR OPENING INDICATOR
1. If any door is opened, door opening indicator will be turned on.
2. In case that any door was opened around 30 seconds, warning beep sound will ring
three (3) times.
3. In case of passing around 1 minute, warning beep sound will ring again five (5) times.
4. In case of passing around 5 minutes, the beep sound will ring continuously.
5. The beep sound will stop immediately if door is closed properly.
12
Turbo air
BEFORE REQUESTING SERVICE
SYMPTOMS
CAUSES
SOLUTIONS
Freezer is melting
food.
• The controller is set too high to • Turn the temperature dial to a
contain food fresh.
warmer position.
The unit does not
refrigerate at all.
• There is a power connection
failure problem.
•
Check the power cord and plug in
it correctly
.
• The unit is in sunlight or near a • Check the installation place.
heating device. • Check the condition of stored
• The unit contains hot food or too food.
much food.
• Check the position of the temp
control dial.
The unit does not
refrigerate well.
• The unit door is opened too
frequently or left open long.
• The temp. dial is not on the
correct position.
• The condenser is clogged.
• The floor is too weak or the
leveling feet is set incorrectly.
• The back-side of the unit is too
close to the wall.
• Check the installation and
adjust the tray position.
There is a loud noise.
• The tray is not in the correct
position.
There are dew-drops
on the unit exterior.
• High-moisture air can produce • Wipe with a dry cloth.
dewdrops during rainy season.
• The door is opened too
frequently or left open long.
• Damp food is stored.
• Keep the door closed to
remove dewdrops.
There are dew-drops
on the unit interior.
• The door is bent.
• The unit is a levelling failure.
• The door gasket has come out.
• Level the unit again.
• Reposition the gasket.
The door does not
close tightly.
The following points are not malfunctions:
• A water-flowing sound can be heard when the compressor stops.
This is the sound of REFRIGERANT flowing.
• The compressor does not run against defrosting function.
13
Turbo air
MANUFACTURING COMPANY
ONE YEAR WARRANTY
Turbo air warrants to the original purchaser of every new-Turbo air refrigerated unit, the cabinet and all parts thereof, to be
free from defects in material or workmanship, under normal use and service, for a period of one (1) year from the date of
original installation or 15 months after shipment date from Turbo air , whichever occurs first.
Any parts covered by this warranty that are examined and determined by Turbo air to have been defective within one (1)
year of original installation or fifteen (15) months after shipment date from manufacturer, whichever occurs first, shall be
repaired or replaced as stated below. Turbo air shall be deemed to have fully complied with its obligation under the
foregoing warranties by electing either one of the following procedures, at the sole discretion of Turbo air.
1. Furnishing a replacement part, freight collect, in even exchange for the returned part, freight collect.
2. Receiving the defective part, freight collect; repairing it; and returning it, freight collect.
ADDITIONAL FOUR YEAR COMPRESSOR WARRANTY
In addition to the (1) one year warranty stated above, Turbo air warrants its hermetically and semi-hermetically sealed
compressor to be free from defects in both material and workmanship under normal use and service for a period of four (4)
additional years from the date of original installation but not to exceed five (5) years and three (3) months after shipment
from manufacturer.
Compressors determined by Turbo air have been defective within this extended time period will, at Turbo air’s option, be
either repaired or replaced with a compressor or compressor parts of similar design and capacity.
The four (4) year extended compressor warranty applies only to hermetically and semi-hermetically sealed parts of the
compressor and does not apply to any other parts or components, including, but not limited to, cabinet, paint finish,
temperature control, refrigerant, metering device, driers, motor starting equipment, fan assembly any other electrical
component, etc.
134a (404A) COMPRESSOR WARRANTY
The four year compressor warranty detailed above will be voided if the following procedure is not carefully adhered to:
1. This system contains 134a (R404A) refrigerant and polyol ester lubricant. The Poyol ester lubricant has rapid moisture
absorbing qualities. If long exposure to the ambient conditions occur, the lubricant must be removed and replaced with
new. Listed below are the approved lubricants for the Tecumseh compressors.
1. ICI-Emkarate RL 184
2. Emery-2927-A
3. Mobile Artic 22A
Failure to comply with recommended lubricant specification will void the compressor warranty.
2. Dryer replacement is very important and must be changed when a system is opened for servicing. Dryer must be used
with XH-9 desiccant.
3. Micron level vacuums must be achieved to insure low moisture levels in the system. 500 microns or lower must be
obtained.
WARRANTY
REGISTRATION
CARD
TURBO AIR MANUFACTURING COMPANY LONG BEACH, CA90807, Plant Incheon R.O.K
(Name of Company purchasing cooler)
MANUFACTURING COMPANY
MAIL CARD
(Type of Business)
(City and State of Purchaser)
IMMEDIATELY
(Model No. of Cooler)
(Cabinet Serial Number)
(Compressor Serial Number)
This is to inform TURBO AIR MANUFACTURING COMMPANY that I,
This card must be
mailed immediately
after installation
date for warranty to
be in effect.
(Signature of individual who owns a Business)
(Installation date)
have had the above TURBO AIR COOLER installed in my place of business
The above warranties are in effect from this installation date, or 90 days after shipment from TURBO AIR, whichever comes first.
MANUFACTURING COMPANY
14
Turbo air
WHAT IS NOT COVERED BY THIS WARRANTY
Turbo air’s obligation under warranty is limited to either repair or replacement of parts, subject to the additional limitations
below. This warranty neither assumes nor authorizes any person to assume obligations other than expressly covered by
this warranty.
1. WARRANTY IS NOT TRANSFERABLE. This warranty is not assignable and applies in favor of the original
purchaser/user to whom delivered. Any such assignment or transfer shall void the warranties herein made and shall void
all warranties, express or implied, including any warranty of merchantability or fitness for a particular purpose.
2. NO CONSEQUENTIAL DAMAGES. Turbo air is not responsible for economic loss: profit loss or special, indirect, or
consequential damages, including without limitation, losses or damages arising from food or product spoilage claims
whether or not on account of refrigeration failure.
3. ALTERATION, NEGLECT, ABUSE, MISUSE, ACCIDENT, DAMAGE DURING TRANSIT OR INSTALLATION, FIRE,
FLOOD, ACTS OF GOD. Trubo air is not responsible for the repair or replacement of any parts that Turbo Air determines
have been subjected after the date of manufacture to alteration, neglect, abuse, misuse, accident, damage during transit
or installation, fire, flood, or an Act of God.
4. NO IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. There are no
other warranties, express, implied or statutory, except the one(1) year warranty and the additional four(4) year
compressor warranty as described above. These warranties are exclusive and in lieu of all other warranties, including
implied warranty and merchantability or fitness for a particular purpose. There are no warranties which extend beyond the
description on the face hereof.
5. TRANSPORTATION COSTS. Turbo Air will accept parts covered under this warranty freight collect, provided that
shipment has received prior approval. Turbo Air is not responsible for any other transporation costs, but will ship freight
collect parts either repaired or replaced under these warranties.
6. WARRANTY CLAIMS. All claims should include: model number of the cooler, the serial number of the cabinet, proof of
purchase, date of installation, and all pertinent information supporting the existence of the alleged defect. Any action or
breach of these warranty provisions must be commenced within one (1) year after that cause of action has accused.
✂
1250 Victoria street
CARSON, CA 90746
TEL: 310-900-1000
FAX: 310-900-1077
Toll Free: 1-800-627-0032
(U.S.A. & Canada)
15
Turbo air
Warranty Claims...
All claims for parts or labor must be made directly thorough Turbo Air.
All claims should include: model number of the unit, the serial number of the cabinet, proof of purchase, date of installation, and all
pertinent information supporting the alleged defect.
In case of compressor replacement under warranty, either compressor or compressor tag must be returned to Turbo Air along with
above listed information.
Failure to comply with warranty policies will result in voiding claims.
One Year Parts & Labor Warranty...
Turbo Air warrants all new refrigerated components, the cabinet and all parts, to be free from defects in materials or workmanship,
under normal and proper use and maintenance service as specified by Turbo Air and upon proper installation and start-up in
accordance with the instruction packet supplied with each Turbo air unit. Turbo Air’s obligation under this warranty is limited to a period
of one (1) year from the date of original installation or 15 months after shipment date from Turbo Air, whichever occurs first.
Any part, covered under this warranty, that are by Turbo Air to have been defective within one (1) year of original installation or fifteen
(15) months after shipment date from manufacturer, whichever occurs first, is limited to the repair or replacement, including labor
charges, of defective parts or assemblies. The labor warranty shall include standard straight time labor charges only and reasonable
travel time, as determined by Turbo Air.
Additional Four Year Compressor Warranty...
In addition to the one (1) year warranty stated adove, Turbo Air warrants its hermetically sealed compressor to be free from defects in
both material and workmanship under normal and proper use and maintenance service for a period of four (4) additional years from
the date of original installation, but not to exceed five (5) years and three(3) months after shipment from the manufacturer.
Compressor determined by Turbo Air to have been defective within this extended period will, at Turbo Air’s discretion, be either
repaired or replaced with a compressor or compressor parts of similar design and capacity.
The four(4) year extended compressor warranty applies only to hermetically sealed parts of the compressor and does not apply to any
other parts or components, including, but not limited to, cabinet, paint finish, temperature control, refrigerant, metering device, driers,
motor starting equipment, fan assembly or and other electrical components, etcetera.
404A / 134a Compressor Warranty...
The four-year compressor warranty detailed above will be void if the following procedure is not carefully adhered to:
1. This system contains R404A or R134a refrigerant and polyol ester lubricant. The polyol ester lubricant has rapid moisture absorbing
qualities.
2. Drier replacement is very important and must be changed when a system is opened for servicing. A620 copper drier or better is
highly recommended.
3. Micron level vacuums must be achieved to insure low moisture levels in the system. 500 microns or lower must be obtained.
4. When compressor is grounded, suction drier and 620 drier or better must be replaced.
5. Compressor must be obtained through Turbo Air, unless otherwise specified in writing, through Turbo Air’s warranty department.
404A / 134a Compressor Warranty...
Turbo Air’s sole obligation under this warranty is limited to either repair or replacement of parts, subject to the additional limitations
below. This warranty neither assumes nor authorizes any person to assume obligations other than those expressly covered by this
warranty.
NO CONSEQUENTIAL DAMAGES. TURBO AIR IS NOT RESPONSIBLE FOR ECONOMIC LOSS; PROFIT LOSS; OR SPECIAL,
INDIRECT, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOSSES, OR DAMAGES ARISING FROM
FOOD OR PRODUCT SPOILAGE REGARDLESS OF WHETHER OR NOT THEY RESULT FROM REFRIGERATION FAILURE.
WARRANTY IS NOT TRANSFERABLE, This warranty is not assignable and applies only in favor of the original purchaser/user to
whom delivered. ANY SUCH ASSIGNMENT OR TRANSFER SHALL VOID THE WARRANNTIES HEREIN AND SHALL VOID ALL
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR LABOR COVERAGE FOR
COMPONENT FAILURE OR OTHER THE WARRANTY PACKET PROVIDED WITH THE UNIT.
ALTERATION, NEGLECT, ABUSE, MISUSE, ACCIDENT, DAMAGE DURING TRANSIT OR INSTALLATION, FIRE, FOOD, ACTS
OF GOD. Turbo Air is not responsible for the repair or replacement of any parts that Turbo Air determines have been subjected after
the date of manufacture to alteration, neglect, abuse, misuse, accident, damage during transit or installation, fire, flood, or act of GOD.
IMPROPER ELECTRICAL CONNECTIONS. TURBO AIR IS NOT RESPONSIBLE FOR THE REPAIR OR REPLACEMENT OF
FAILED OR DAMAGED COMPONENTS RESULTING FROM ELECTRICAL POWER FAILURE, THE USE OF EXTENSION CORDS,
LOW VOLTAGE, OR VOLTAGE DROPS TO THE UNIT. NO IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE; THERE ARE NO OTHER WARRANTIES, EXPRESSED, IMPLIED OR STATUTORY, EXCEPT THE ONE
(1) YEAR PARTS & LABOR WARRANTY AND THE ADDITIONAL FOUR (4) YEAR COMPRESSOR WARRANTY AS DESCRIBED
ABOVE. THESE WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, INCLUDING IMPLIED WARRANTY
AND MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THERE ARE NO WARRANTIES, WHICH EXTEND
BEYOND THE DESCRIPTION ON THE FACE HEREOF.
Outside U.S.and Canada; This warranty does not apply to, and Turbo Air is not responsible for, any warranty claims made on products
sold or used outside the continent of the United States and Canada.
CHANGES MADE TO WARRANTY COMMENCED ON 11/01/2007
|