Quickstart Guide
NuQ series
Models covered by this Quickstart Guide
NuQ-6, NuQ-8/DP, NuQ-10/DP, NuQ-12/DP, NuQ-15/DP, B-12DP, B-15/DP, B-18/DP.
Thank you for choosing a TURBOSOUND loudspeaker product for your application. If you would like further information
about this or any other TURBOSOUND product, please contact us on +44 (0)1403 711447. A detailed user manual on this
product range is available on our website at http://www.turbosound.com
Unpacking the Loudspeaker
After unpacking the unit please check carefully for damage. If damage is found, please notify your supplier at once. You,
the consignee, must instigate any claim. Please retain all packaging in case of future re-shipment.
System Requirements – Passive and Bi-amped Loudspeakers
The NuQ-6, NuQ-8, and NuQ-10 two-way loudspeakers are passive systems and
Passive Speakon
2+
1-
require only one amplifier channel for correct operation, the frequency splitting
between the LF driver and the HF driver being accomplished by the internal
passive crossover network built into each enclosure. They are equipped with
two Neutrik Speakon NL4MP connectors wired in parallel, serving as both input
and loop-out connections to additional speakers. The Speakon wiring details are
shown at the right. The NuQ-12 and NuQ-15 two-way loudspeakers are
switchable passive/bi-amped systems and require two amplifier channels when
used in bi-amped mode. To avoid wasting amplifier power you should use
heavy-duty speaker cable with a minimum wire size of 12 gauge (1.5mm²), and
preferably 10 gauge (2.5mm²) for longer runs. Always observe the correct
polarity as shown.
connections
(Pins 2+ and 2- not connected)
2- 1+
Negative (-ve)
Positive (+ve)
HF Negative (-ve)
HF Positive (+ve)
2+
1-
Bi-amped Speakon
connections
2- 1+
LF Negative (-ve)
LF Positive (+ve)
Amplifier considerations
NuQ series speaker enclosures should be driven by high quality power amplifiers designed for true professional use.
Amplifiers should be capable of delivering long term broadband power equal to the loudspeaker’s program power rating
at its stated nominal impedance. The use of under-powered amplifiers must be avoided as heavily clipped signals can
cause permanent loudspeaker damage.
Model
NuQ-6
NuQ-8
NuQ-10
NuQ-12
NuQ-15
B-15
B-18
Impedance
8
8
8
Passive: 8
Passive: 8
8
8
LF: 8, HF: 6
LF: 8, HF: 6
RECOMMENDED AMPLIFIER POWER RATING
The amplifier’s rated r.m.s. continuous power output (20Hz – 20kHz, each channel)
should be equal to the loudspeaker’s program power handling at its nominal impedance.
System Controllers and Bi-amplified systems
NuQ systems must be used with Turbosound LMS-D24 or LMS-D26 controllers, since these provide vital operating and
system security features. If you do not have a controller, DO NOT USE the loudspeaker without one; please contact your
Turbosound dealer for further details.
NuQ Series Quickstart Guide v1.2 - Page - 1
Quickstart Guide
NuQ series
network protocol among the networked devices and is carried over CAT5-type cables. Minimum system requirements are:
PC with Pentium processor, Windows NT, 2000, XP, or Vista, CD ROM drive or internet access, RS232 or USB port
RS232:Connect your computer to the BvNet interface using a standard 9-pin serial cable. External power is required for
RS232 operation and this should be supplied by the Linea Research Accessory Power Supply
USB: Connect your computer to the BvNet interface using a USB Type A to USB Type B cable. External power is not
required when using USB
Connect networked devices via RJ45 CAT5 cables
Launch the TurboDrive™ software
Application Authorisation: TurboDrive™ prompts for an Authorisation Code on the first launch which is PJLUWZ
Select the COM port from Network > Com Port
Click the Online toolbar button
Click on one of the devices that appear in the tree view to Launch the panel
When the progress bar indicates ready, adjust the controls as required
Please refer to the TurboDrive™ User Guide for further information on networking.
Mounting and Fixing
NuQ series two-way cabinets are equipped with pole mount sockets for portable use on 35mm speaker stands or poles.
Bass cabinets are equipped with pole mount receptacles that allow two-way cabinets to be mounted at the correct height.
NuQ series cabinets can be suspended in permanent installations using optional shoulder eyebolts coupled to the internal
rigging points provided. To install using eyebolts, remove the appropriate countersunk screws and replace them with
eyebolts, which must have a thread length of at least 18mm. Use the rear rigging point to angle the cabinet for optimum
room coverage. Cabinets may be hung upside down if required.
Turbosound wall and ceiling brackets are optionally available for installing non-powered NuQ series cabinets. They are
also compatible with OmniMount™ wall and ceiling brackets. Some examples are shown below.
Model
Wall Mount
Flying Yokes
Swivel
Swivel
OmniMount™
Eyebolts
brackets
extenders
NuQ-6
NuQ-8
n/a
NuQ-FY6
NuQ-FY8
NuQ-SB6
NuQ-SB8
n/a
n/a
M8
WB-20B
PB-55
NuQ-SBE8
20.5 Series
M10
NuQ-10
NuQ-12
NuQ-15
WB-20B
PB-55
NuQ-FY10
NuQ-FY12
NuQ-FY15
NuQ-SB10
n/a
NuQ-SBE10
60 Series
60 Series
120 Series
M10
M10
M10
WB-55B
PB-55
n/a
n/a
WB-55B
PB-55
n/a
NuQ Series Quickstart Guide v1.2 - Page - 3
Quickstart Guide
NuQ series
SC-01
Scaffold Clamp
NuQ-FY8
Flying yoke
WB-20B
PB-55
Wall Bracket
Pole Bracket
SC-01
Scaffold Clamp
SC-01
Scaffold Clamp
NuQ-FY8
FlyingYoke
NuQ-TB
Twin Bar
NuQ-SB8
Swivel bracket
NuQ-SBE8
Extender Bar
To install a loudspeaker using Turbosound brackets, first separate the brackets into their wall/ceiling plate and speaker
plate component parts. Remove the two countersunk M10 bolts on the rear panel of the cabinet. Attach the speaker plate
to the cabinet with the M8 bolts supplied. Fix the wall/ceiling plate in the venue using appropriate fixings (not supplied).
Lift the loudspeaker on to the wall plate and re-assemble the bracket parts, adjust the vertical angle and tighten all bolts.
IMPORTANT NOTE: The rigging of a flown sound system may be dangerous unless undertaken by qualified personnel
with the required experience and certification to perform the necessary tasks.
Spares and Accessories
CD-115 / RD-115
Compression driver / diaphragm for NuQ-6, NuQ-8, NuQ-10
Compression driver / diaphragm for NuQ-12, NuQ-15
6.5” low frequency loudspeaker / recone kit for NuQ-6
8” low frequency loudspeaker / recone kit for NuQ-8/DP
10” low frequency loudspeaker / recone kit for NuQ-10/DP
12” low frequency loudspeaker / recone kit for NuQ-12/DP
12” low frequency loudspeaker / recone kit for B-12DP
15” low frequency loudspeaker / recone kit for NuQ-15/DP
15” low frequency loudspeaker / recone kit for B15/DP, B215/DP
18” low frequency loudspeaker / recone kit for B18/DP
CD-213.2/RD-213.2
LS-6509 / RD-6509
LS-8093 / RC-8093
LS-1024 / RC-1024
LS-1221 / RC-1221
LS-1220 / RC-1220
LS-1528/ RC-1528
LS-1526 / RC-1526
LS-1814 / RC-1814
NuQ series self-powered products comply with the following European Community standards: EN60065:2003 (Safety),
EN66103-1:1996 and EN55103-2:1996. All products are CE marked in accordance with the relevant statutory requirements.
Turbosound Ltd, Star Road, West Sussex RH13 8RY, UK
NuQ Quickstart Guide v1.2 - Page - 4
|