Exchangeable colorful handset ring
Record outgoing announcement (optional)
2
1
Your telephone comes with additional colorful handset
rings. Change it to suit your mood or match your
room decor.
To remove the handset ring:
1. Insert your thumbnail into the slot underneath the
MENU��ELECT button.
2. Lift up the colorful handset ring.
To install a new handset ring:
The telephone is preset with a greeting that answers
calls with “Hello, please leave a message after the tone.”
You can use this preset announcement, or replace it
with your own. While in the ANNC menu, press ANNC
again to exit at anytime.
Quick start guide
�����������������
for models ������������������
To replace the default announcement:
Telephone base installation
1. Press ANNC while in idle mode and the system will
announce “Announcement, press PLAY or press
RECORD.”
2. Press RECOR� and the system announces “Record
after the tone, press STOP when you are done.”
3. After the tone, speak towards the microphone at the
bottom front of the telephone base from about nine
inches away.
1. Plug the connector into the power jack at the
bottom of the telephone base and chargers then
plug the power adapter into an electrical outlet not
controlled by a wall switch.
2. Plug one end of the telephone line cord into the
telephone line jack at the bottom of the telephone
base. Then plug the other end of the cord into the
modular wall telephone outlet.
1. Align the desired handset ring against the
4
3
MENU��ELECT button.
2. Press the colorful handset ring downward until it
clicks into place.
�et the answering system clock
4. Press �PLAY��TOP when finished.
5. The answering system will automatically playback
the newly recorded announcement and there will be
a confirmation tone. Press �PLAY��TOP to stop
the playback at anytime.
6. Press �PLAY��TOP again to replay the recorded
announcement. Press RECOR� to record again if
you do not like the announcement just recorded.
Press ANNC to exit and return to idle mode.
1. Press CLOCK and the system will announce
the current clock setting. The system will then
announce “To set the CLOCK, press CLOCK.”
2. Press CLOCK again and the system will announce
Make, receive and end calls
Make a call
the year.
3. Press ��KIP or /REPEAT until the system
announces the correct year, then press CLOCK.
The system will announce the hour.
4. Press ��KIP or /REPEAT, until the system
announces the correct hour, then press CLOCK.
The system will announce the minute.
• Press
/FLA�H or
/�PEAKER to ensure there
is a dial tone, then dial the telephone number.
5. Press ��KIP or /REPEAT until the system
announces the correct minutes, then press
CLOCK. The system will announce the day.
NOTE: Use only the power adapters supplied with
your VTech telephone or equivalent.
6. Press ��KIP or /REPEAT until the system
announces the correct day, then press CLOCK.
The system will announce the new clock setting
and return to idle mode.
�OR�
NOTE:
For predialing:
Install and charge the battery
For complete feature instructions, please refer to your
user’s manual.
1. Dial the number (press MUTE�REMOVE or
OFF�CLEAR to backspace, or press and hold
RE�IAL�PAU�E to insert a pause).
1. If the battery compartment cover is on the handset,
press the indentation and slide the cover to
remove.
2. Align the two holes of the battery plug with the socket
pins in the handset battery compartment, matching
the red and black wires to the color-coded label, then
snap the plug securely into place.
3. Place the battery in the compartment with the wires
in the upper left corner.
4. Position the battery compartment cover and slide it
up until it clicks into place.
IMPORTANT!
2. Press
/FLA�H or
/�PEAKER if you want to
If your product is not working properly:
use the speakerphone function.
• Refer to the Troubleshooting section of your
user’s manual.
Receive a call
Activate the answering system
• Press
/FLA�H or
/�PEAKER or any dialing
The answering system must be turned on to function.
If the answering system is turned off, the telephone
base light will be off.
keys (0�9, #, *).
• Call our customer service at 1 (800) 595-9511 or
1 (800) 267 7377 in Canada.
To turn on/off the answering system:
5. Place the handset in the telephone base or charger to
charge. The CHARGE light on the telephone base or
charger will be on when the battery is charging.
• Press AN� ON�OFF to turn on the answering system
and press AN� ON�OFF again to turn it off.
For optimal performance, we recommend that you
charge the handset for 16 hours. The new battery may
have enough charge for some calls.
End a call
• Press OFF�CLEAR or put the handset in the
telephone base or charger.
96-006503-040-100
|