Vector Air Compressor VEC255 User Manual

VEC255  
CORDED, CORDLESS,  
RECHARGEABLE COMPRESSOR  
AND INFLATOR COMBO  
OWNER’S MANUAL  
& WARRANTY INFORMATION  
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING  
SAFETY, OPERATION, MAINTENANCE AND STORAGE OF THIS PRODUCT.  
BEFORE USE, READ AND UNDERSTAND ALL CAUTIONS, WARNINGS,  
INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO SO COULD  
RESULT IN INJURY AND/OR PROPERTY DAMAGE.  
4140 SW 28TH WAY, FT. LAUDERDALE, FL 33312  
TEL 954-584-4446 • TOLL FREE: 866-584-5504 • FAX 954-584-5556  
www.vectormfg.com  
 
internal battery. For immediate use, attach the DC adapter and operate  
the appliances from an external 12 volt DC source.  
4. To avoid over-inflation, carefully follow instructions on articles to be inflated.  
5. Never leave appliances unattended while in use. Allow appliance to cool  
for five minutes after 10 minutes of continuous operation.  
6. Do not use accessories that are not designed to be used with these  
appliances.  
7. Do not place battery pack on heater and keep it out of sunlight.  
8. Do not charge battery when it is at or above 122° F (50° C). Allow the  
battery pack to cool before charging.  
CONTENTS  
1. INTRODUCTION .................................................... 4  
2. ADDITIONAL KEY FEATURES .................................. 5  
3. ATTACHING THE COMPRESSOR’S AIR HOSE.......... 6  
4. POWERING THE COMPRESSOR OR INFLATOR ....... 6  
4.1 Powering from the battery pack ........................  
4.2 DC Power Adapter Use .................................. 6  
5. CHARGING/RECHARGING THE BATTERY PACK...... 7  
5.1 AC Recharge of battery pack.......................... 7  
6. COMPRESSOR/TIRE INFLATOR............................... 8  
6.1 Tire inflation or products with a valve stem ....... 8  
6.2 Inflate other articles (without valve stem) .......... 9  
7. TYPICAL INFLATION TIMES ..................................... 9  
8. LOW PRESSURE INFLATOR ................................... 10  
8.1 Inflator ........................................................ 11  
8.2 Deflator ...................................................... 11  
9. MAINTENANCE/REPLACEMENT PARTS ................ 11  
10. BATTERY REPLACEMENT....................................... 11  
11. BATTERY DISPOSAL .............................................. 12  
12. SPECIFICATIONS ................................................. 12  
WARRANTIES ................................................. 13,14  
 
3
1.  
INTRODUCTION  
Congratulations on selecting the Vector Air Pro™ Model VEC255  
Compressor & Inflator Combo. This system is an advanced high-pressure  
(up to 260 PSI) multi-use air compressor system with unique features that set  
it far above the value and utility of ordinary compressors for mobile use. It is  
supplied with a standard tire valve chuck for filling auto, truck, bike, and  
motorcycle tires. Additionally, two different adapters are supplied to inflate  
soccer balls, footballs, and popular inflatables. These adapters are conve-  
niently stored in a hatch in the compressor body. It is powered from its own  
snap-on/off powerful battery to be used anywhere it is needed. It can also  
operate from a standard 12 volt DC electrical system found on: trucks, cars,  
boats, airplanes, RVs and tractors, using the supplied DC Power Adapter. A  
supplied standard 110 VAC charger recharges the battery when required.  
Typically, up to three completely flat tires can be inflated before the snap-on  
battery has to be recharged.  
A separate Inflator shares the battery pack and DC Power Adapter. The inflator  
is used to inflate: air mattresses; beach balls, etc.(See Sections 8 thru 10)  
A customer can purchase extra snap-on battery packs if completely cordless  
operation is required (Part VEC194). Operating these appliances with the  
snap-on DC Power Adapters is ideal for use with Vector 12 volt DC cordless,  
portable, rechargeable DC Power supplies if extended operating time in the  
field is required.  
FIGURE 1  
HOSE RETAINING  
RING  
NOZZLE HATCH  
COVER  
COMPRESSOR  
OUTLET  
RIBBED BRASS  
FITTING  
TRIGGER LOCK  
COMPRESSOR  
HOSE  
TRIGGER  
SWITCH  
TIRE CHUCK  
4
 
4
The Compressor On/Off Switch controls operation of the compressor. It  
conveniently is depressed and released to control inflation. An exact pres-  
sure is obtained by observing the gauge and releasing the trigger when the  
correct pressure is achieved. For longer inflation operations, the Trigger  
Lock can be moved laterally to lock the trigger in the ON position. Pushing  
the trigger lock to the opposite direction releases the trigger (OFF) and  
inflation stops.  
2.  
ADDITIONAL KEY FEATURES  
• Trigger Switch with lock to allow hands free operation  
• Corded -includes a DC power adapter for use with standard 12 volt power  
supply  
• Battery Pack includes non-spillable, maintenance-free, heavy duty, sealed,  
high-density lead-acid battery  
• Requires no maintenance (other than recharging and cleaning) for  
optimum operation  
• Supplied 110 volt AC charger is Underwriter Laboratories (UL) safety  
tested and listed  
• Battery Charging LED on battery automatically activated during  
AC recharge  
• Analog Pressure Gauge to 260 PSI Compressor  
• Nozzle Hatch for storing nozzles in compressor  
• 3 nozzles for inflator  
NOZZLE HATCH  
FIGURE 2  
COVER  
NOZZLES  
PRESSURE  
GAUGE  
CAUTION: This battery pack is delivered in a partially charged state - you  
must fully charge it before using it for the first time. Initial AC Charge  
should be for 10 hours. Refer to Section 6 for use of AC Adapter and  
detailed charging instructions.  
 
5
3.  
ATTACHING THE COMPRESSOR’S AIR HOSE  
The Air Hose is supplied as a separate item from the compressor body. The  
hose has a ribbed brass fitting at one end and a standard tire chuck at the  
other end. To use the hose it must first be connected to the compressor outlet.  
Loosen the Hose retaining ring (counterclockwise), insert the hose fitting into  
the short, rubber sealing sleeve. Make sure the hose fitting is inserted fully  
into the sleeve. Partially tighten (clockwise) the hose-retaining ring and push  
the fitting in further. Do this two or three times until the fitting is firmly  
attached and the ring is firmly tightened.  
WARNING: Improperly attached hoses or nozzles can fly out under  
compressor pressure. Make sure the connections are tight.  
WARNINGS:  
1. There is risk of dust or dirt projectiles being released if the compressor  
hose or nozzles are not clean when the compressor is turned on.  
2. Wearing protective goggles while operating this compressor can protect eyes  
from flying particles of dust and dirt. Failure to follow instructions may cause  
property damage, and/or personal injury.  
3. Keep out of reach of children.  
4.  
POWERING THE COMPRESSOR OR INFLATOR  
The compressor can be powered either from a supplied battery pack or  
from a supplied DC Power Adapter.  
4.1 POWERING FROM THE BATTERY PACK  
The supplied battery pack powers the compressor or inflator for short  
duration, cordless operation. The Battery Pack should be fully charged  
initially before use (see paragraph 5 for charging instructions.)  
To connect the charged battery pack to either the compressor or inflator,  
align the battery pack so that the battery release buttons snap onto the  
appropriate appliance. The battery pack fits only one way to ensure correct  
polarity of the contacts. To remove the Battery Pack, press the Battery Pack  
Release buttons and the battery pack will separate from the appliance.  
4.2 DC POWER ADAPTER USE  
The DC power adapter can power the compressor or inflator for longer  
operation from an external 12 volt power source.  
6
 
6
The DC Power Adapter has a fused DC plug and connecting cord stored  
inside the DC Power Adapter. To use the DC Power Adapter, first remove the  
DC plug from it’s storage in the adapter. Deploy the cord from storage, and  
connect the DC Power Adapter to the compressor. Make sure it snaps into  
position. Connect the DC plug to a 12 VDC source. To remove the DC Power  
Adapter, press it’s release buttons and the Adapter will separate from the  
compressor. Put the DC Plug and cord in the Adapter for storage after use.  
FIGURE 3  
CONTACT  
FUSED DC  
PLUG  
RELEASE  
BUTTON  
5.  
CHARGING/RECHARGING THE BATTERY PACK  
Lead-acid batteries require maintenance to maintain a full charge and to  
ensure good battery life. All lead-acid batteries suffer from self-discharge  
over time and more rapidly when they are at higher temperatures.  
Therefore, these types of batteries need periodic charging to replace energy  
lost through self-discharge. When the Battery Pack is not in use Vector  
recommends that the battery is recharged at least every 60 days.  
All batteries must be recharged as soon as possible after each use. If a battery is  
allowed to remain in a discharged state, battery life will be reduced.  
NOTE: Recharging battery after each use will prolong battery life; frequent  
heavy discharges between recharges will reduce battery life.  
Overcharging will reduce battery life. Never charge for more than 24 hours.  
The time required to fully recharge the battery pack depends on the charge  
status of the battery after it’s use. If the battery is discharged from recent use  
recharge the battery for 8 hours.  
5.1 AC RECHARGE OF BATTERY PACK  
AC Recharge requires the use of the supplied AC/DC Adapter. The AC  
adapter must be powered from 110 volt AC, 60 Hz North American  
standard AC receptacles. The battery pack must be removed from the  
compressor body to gain access to the recharge port.  
 
7
CONTACTS  
RECHARGE PORT  
RECHARGE LED  
FIGURE 4  
RELEASE  
BUTTON  
110 VOLT AC  
WALL ADAPTOR  
WITH CORD  
To remove the battery pack from the appliance body for charging: Make  
sure the trigger switch is OFF. Press both battery pack release buttons at the  
same time. Pull the battery pack down away from the appliance body. Insert  
the barrel connector of the AC Adapter into the battery pack’s receptacle  
(Recharge Port). Plug the AC Adapter into a 110 VAC standard household  
receptacle. Observe the red LED lights. Charge for the  
recommended time. Do not overcharge! Disconnect and store the AC  
Recharge Adapter from the battery pack and AC source when not in use.  
6.  
COMPRESSOR/TIRE INFLATOR  
This 12 Volt DC compressor is the ultimate compressor for all Vehicles, Trailer  
Tires and recreational inflatables. Three different sized nozzles are supplied.  
IMPORTANT: Read safety Instructions Carefully To Avoid Possible Injury  
Or Property Damage.  
WARNINGS: The compressor is capable of inflating to 260 pounds per  
square inch (PSI) pressure (approximately 18 kg/cm). To avoid over-  
inflation, carefully follow instructions on articles to be inflated. Never  
exceed recommended pressures. Bursting articles can cause serious  
injury. Always check pressure with the pressure gauge. Never leave  
compressor unattended while in use. Allow unit to cool for five minutes  
after 10 minutes of continuous operation.  
6.1 TIRE INFLATION OR PRODUCTS WITH A VALVE STEM  
1. Place connector (chuck) on valve stem.  
2. Push connector toward valve stem and close thumb latch.  
3. Make sure connector is pushed on to valve stem as far as possible before  
closing thumb latch.  
8 4. Turn on the compressor (for larger items the trigger can be latched)  
 
8
5. Observe pressure with the pressure gauge.  
6. When desired pressure is reached, open thumb latch and remove  
connector from valve stem.  
7. Turn OFF Compressor Power Switch  
IMPORTANT: Always leave the tire chuck thumb latch in the open  
position when storing unit.  
6.2 INFLATE OTHER ARTICLES (WITHOUT VALVE STEM)  
Inflation of other than tires requires use of one of the nozzles (adapters). A  
nozzle can be attached to the tire chuck or it can directly be connected to the  
compressors outlet if the hose is removed.  
A nozzle can be attached to the tire chuck. Open the nozzle hatch cover  
and remove the required nozzle. Close the nozzle hatch cover. Place the tire  
chuck over the nozzle fitting and secure by moving the chuck thumb latch so  
it is parallel with the hose. Make sure the nozzle is clean and secure before  
turning on the compressor. After use, release the nozzle from the chuck by  
lifting the latch. Return the nozzle to the nozzle hatch.  
A nozzle can also be directly attached to the Compressor Outlet if the hose  
is not required.  
1. Open the nozzle hatch cover and remove the required nozzle.  
2. Remove the hose from the compressor outlet by loosening (counterclock  
wise) the hose retaining ring and sliding out the ribbed brass fitting.  
3. Close the nozzle hatch cover.  
4. Insert the selected nozzle into the compressor outlet and secure it by  
tightening the hose-retaining ring as above.  
5. After using the compressor, remove and store the nozzle in the nozzle  
hatch.  
Refer to “Typical Inflation Times” for approximate pressure and time. Small  
items like volleyballs, footballs, etc. inflate very rapidly.  
6. Insert nozzle (e.g needle) into item to be inflated and inflate to  
desired pressure.  
7. Turn ON compressor switch - inflate to desired pressure or fullness.  
 
9
7.  
TYPICAL INFLATION TIMES FOR COMPRESSOR USE  
The following are approximate pressure and inflation times for various items.  
WARNING: Always follow tire manufacturers recommendations for  
pressure on item to be inflated.  
VEHICLE AND TRAILER TIRES  
TIRE SIZE ................... PRESSURE ................... TIME FROM “0” PRESSURE  
155/80R 13" ......... 26 PSI ........................... 2.50 MIN.  
185/70R 14" ......... 30 PSI ........................... 4.50 MIN.  
235/75R 15" ......... 30 PSI ........................... 6.50 MIN.  
235/85R 16" ......... 50 PSI ........................... 16.00 MIN.  
BICYCLE TIRES  
TIRE SIZE ................... PRESSURE ................... TIME FROM “0” PRESSURE  
27  
X
1" RACING ........ 10 PSI ........................... 40 SEC.  
INFLATABLE ARTICLES  
ITEM ..................... PRESSURE ................... TIME FROM “0” PRESSURE  
FOOTBALL ................. 13 PSI ........................... 24 SECONDS  
BASKETBALL ................ 9 PSI ............................. 20 SECONDS  
VOLLEYBALL ............... 5 PSI ............................. 6 SECONDS  
8.  
LOW PRESSURE INFLATOR/DEFLATOR  
Congratulations on your purchase of the Vector Inflator/Deflator -The ultimate  
inflator for all high volume, low-pressure recreational inflatables. The VEC255  
Combo Inflator/Deflator is supplied with three different sized nozzles. Each nozzle  
will fit either the inflation port or the deflation port.The nozzles are supplied on  
a cord attached to the inflators body. The nozzles will not get lost. An On/Off  
switch located on the body of the inflator allows the Inflator/ Deflator to be  
switched OFF and remain connected to the battery pack or the DC Power Adapter  
during nozzle changes  
DEFLATION  
PORT  
FIGURE 3  
INFLATION  
PORT  
ON/OFF  
SWITCH  
3 NOZZLES  
10  
 
10  
8.1  
INFLATING  
1. Connect the inflator/deflator to either the battery pack or the DC Power  
Adapter.  
2. Be sure the appropriate nozzle head is attached to the tapered inflating  
port of the inflator/deflator unit. Push the nozzle onto the inflation port to  
attach. The inflating port can be identified by location. It is on the side of  
the unit.  
3. Position the nozzle against the valve of the inflatable item. Turn on the  
Inflator/Deflator on using the On/Off switch, and inflate the item to  
desired firmness. After inflation, move the nozzle away from the valve  
and turn the switch OFF.  
8.2  
DEFLATING  
1. Pull off the nozzle from the inflating port of the unit and reinstall it at the  
deflating port of the Inflator/Deflator (on the top of the unit). Press the  
nozzle to attach.  
2. Power the Inflator with either the battery pack or the DC Adapter.  
3. Position the nozzle against the valve of the inflated item. Turn On the  
sport inflator/deflator using the On/Off switch and deflate the item.  
NOTE: If the inflatable item’s air valve is equipped with a safety flap, it  
maybe necessary to hold the flap open with a pencil or similarly shaped  
object to deflate the item.  
9.  
MAINTENANCE/REPLACEMENT PARTS  
For replacement parts (batteries, DC Power Adapters, AC charging  
adapters, cables, etc.), contact Vector Technical Support: (954) 584-4446 or toll  
free at 866-584-5504. Periodically, cables, hose, nozzles and connectors should  
be inspected for damage, corrosion, dust and dirt. If surfaces are dirty, they can  
be wiped clean with a cloth moistened with water and a drop of detergent.  
Battery Pack contacts can be wiped clean with a dry cloth.  
10.  
BATTERY REPLACEMENT  
The battery in the battery pack should be replaced with a new one when the  
operating capacity is reduced to about one half or the ability to inflate one  
and one half average sized automobile tires. Make sure that the battery is  
fully charged before determining that the battery pack should be replaced.  
Contact Vector Technical Support and ask for part VEC194. This battery  
pack is also used with other Vector products that include portable inflators  
and spotlights. For more details, please contact our Sales or Technical  
Support Department at 1-866-584-5504.  
 
11  
11.  
BATTERY DISPOSAL  
Contains a maintenance-free, sealed, non-spillable, lead acid battery, which  
must be disposed of properly. Most states require recycling-contact your  
local municipal authority for information.  
Non-spillable sealed lead-acid battery, must be recycled or disposed of  
properly. Recycling is required -contact your local authority for information.  
DISPOSAL QUESTIONS FOR USA CALL toll-free 877-288-7722.  
PRBA  
PRBA  
ALWAYS RECYCLE  
WARNINGS:  
Do not dispose of the battery pack in fire as this may result in an explosion  
• Before disposing of the battery pack, protect exposed terminals with heavy-  
duty electrical tape to prevent shorting (shorting can result in injury or  
fire). Failure to comply with local, state and federal regulations can result  
in fines, or imprisonment  
12.  
SPECIFICATIONS  
FOR COMPRESSOR:  
Battery ........... 12 Volt 3 Amp Hour, Non-spillable Sealed Lead-Acid  
Compressor ...................................................... 260 PSI Maximum  
Weight................................................................... 1.82 lbs (4 kg)  
Height w/battery ..................................... 11.25 inches (28.57 cm)  
Width ......................................................... 4.0 inches (10.16 cm)  
Length ............................................................ 7 inches (17.78 cm)  
FOR INFLATOR:  
Nozzles ........................................................................................ 3  
Voltage ................................................................. DC - 12V nominal  
Current ................................................................... Approx. 5 Amps  
Air Pressure............................................................... 816 - mm H20  
Delivery Volume .................................................. 175 CFM per min.  
Typical Inflating time ........................................................ 10 minutes  
12  
 
12  
120 DAY LIMITED WARRANTY REGISTRATION FORM  
This Vector Manufacturing, Ltd. product is warranted to the original  
purchaser only for 120 days from the date of purchase, to be free of defects  
in materials and workmanship. Vector Manufacturing, Ltd. disclaims any  
liability for consequential damages. In no event will Vector Manufacturing,  
Ltd. be responsible for any amount of damages beyond the amount paid for  
the product at retail. In the event of a defective item, please ship the item  
prepaid, with a complete explanation of the problem, your name, address  
and daytime telephone number. Vector Manufacturing, Ltd. will, at its  
option, replace the defective part.  
The following situations are not covered under this warranty:  
Cost of shipment to Vector Manufacturing, Ltd.  
Normal wear and tear, including chips, scratches, abrasions, repairs by  
unauthorized persons or failure to follow recommended care and use  
instructions.  
Damage caused by misuse, abuse, neglect, alterations, repairs by  
unauthorized persons, or failure to follow recommended care and use  
instructions.  
Please activate my Limited Warranty for Model #VEC255. Enclose  
copy of original sales receipt.  
Name ____________________ Street Address _________________  
City ______________________ State ___ Zip Code _____________  
Phone ____________________ Fax ____ E-mail _______________  
Date of purchase ___________ Store where purchased __________  
UPC Number from package (12 digits) ________________________  
All Vector Manufacturing, Ltd. products must be registered within (10) days  
of purchase to activate this warranty. Mail the completed registration form,  
along with a copy of the original sales receipt to:  
ATTN.: CUSTOMER SERVICE / VECTOR MANUFACTURING, Ltd.  
4140 SW 28th Way, Ft. Lauderdale, FL 33312  
 
13  
3 YEAR EXTENDED WARRANTY REGISTRATION FORM  
This limited warranty program is the only one that applies to this product, and it sets forth all the responsibili-  
ties of Vector Manufacturing, Ltd., regarding this product. There is no other warranty, other than those de-  
scribed herein. This Vector Manufacturing, Ltd. product is warranted, to the original purchaser only, to be free  
of defects in materials and workmanship for three years from the date of purchase without additional charge.  
The warranty does not extend to subsequent purchasers or users. Vector Manufacturing, Ltd. will not be  
responsible for any amount of damage in excess of the retail purchase price of the product under any  
circumstances. Incidental and consequential damages are specifically excluded from coverage under this  
warranty. This product is not intended for commercial use. This warranty does not apply to accessories or  
damage to units from misuse or incorrect installation. Misuse includes wiring or connecting to improper  
polarity power sources.  
RETURN/REPAIR POLICY: Defective products, other than accessories, may be returned postage prepaid to  
Vector Manufacturing. Any defective product, other than accessories, that is returned to Vector Manufacturing  
within 30 days of the date of purchase will be replaced free of charge. If such a product is returned more than  
30 days but less than three years from the purchase date, Vector Manufacturing will repair the unit or, at its  
option, replace it free of charge. If the unit is repaired, new or reconditioned replacement parts may be used,  
at Vector Manufacturings option. A unit may be replaced with a new or reconditioned unit of the same or  
comparable design. The repaired or replaced unit will then be warranted under the terms of the remainder of  
the warranty period. The customer is responsible for the shipping charges on all returned items after 30 days.  
During the warranty period, Vector Manufacturing, Ltd. will be responsible for the return shipping charges.  
LIMITATIONS: This warranty does not cover accessories, bulbs, fuses and batteries, defects resulting from  
normal wear and tear (including chips, scratches, abrasions, discoloration or fading due to usage or expo-  
sure to sunlight), accidents, damage during shipping to our service facility, alterations, unauthorized use or  
repair, neglect, misuse, abuse, failure to follow instructions for care and maintenance, fire, flood and Acts of  
God. If your problem is not covered by this warranty, call our Technical Support Department at (954) 584-  
4446 or Toll Free at (866) 584-5504 for general repair information and charges if applicable. You may also  
STATE LAW RIGHTS: This warranty gives you specific legal rights. Some states do not allow limitations on how  
long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the  
exclusions or limitations stated herein may not apply. This warranty gives the purchaser specific legal rights;  
other rights, which vary from state to state, may apply.  
TO REQUEST WARRANTY SERVICE FOR THIS PRODUCT: Contact Vector Manufacturing Technical Support  
by telephone, fax or mail. We suggest that you keep the original packaging in case you need to ship the unit.  
When returning a product, include your name, address, phone number, dated sales receipt (or copy) and a  
description of the reason for return and product serial number. After repairing or replacing the unit, we will  
make every effort to return it to you within four weeks.  
WARRANTY ACTIVATION: Please complete Warranty Activation Card and mail to Vector Manufacturing.  
Enter “VEC255” as Model and “Rechargeable Compressor /Inflator Combo” as Product Type. All Vector  
Manufacturing, Ltd. products must be registered within 10 days of purchase to activate this warranty. Mail the  
completed registration form, along with a copy of the original sales receipt to:  
ATTN.: CUSTOMER SERVICE / VECTOR MANUFACTURING, Ltd.  
4140 SW 28th Way, Ft. Lauderdale, FL 33312  
PH: 954-584-4446 • TOLL FREE: 866-584-5504 • Fax: 954-584-5556.  
WARRANTY IS NON-TRANSFERABLE AND NON-REFUNDABLE.  
14  
 
14  
 
15  
© 2003 VECTOR MANUFACTURING, Ltd.  
FT. LAUDERDALE, FL 33312 MADE IN CHINA  
16  
 

Toastmaster Food Processor TMMC2 User Manual
Toastmaster Kitchen Grill 896S 898S User Manual
Toro Lawn Mower LX420 LX460 User Manual
Transcend Information Computer Drive 25M User Manual
Uniden Conference Phone FP205 User Manual
Uniden Cordless Telephone DECT1580 2 User Manual
Uniden Cordless Telephone EXP7240 User Manual
VeriFone Credit Card Machine QX1000 User Manual
Vizio Blu ray Player XWR100 User Manual
VocoPro Car Amplifier SE 690 Pro User Manual