VEC141
POWER SERIESTM
SPOTLIGHT
2,000,000
CORDED • CORDLESS • RECHARGEABLE
IF YOU SHOULD EXPERIENCE A PROBLEM WITH YOUR
PURCHASE CALL TOLL FREE 866-584-5504. IN MOST
CASES A SERVICE REPRESENTATIVE CAN RESOLVE
YOUR PROBLEM OVER THE PHONE.
KEY INFORMATION YOU SHOULD KNOW:
• REPLACEABLE 12V BATTERY
• PORTABLE, CORDLESS, RECHARGEABLE
• ULTRA BRIGHT AREA LIGHT
• HIGH INTENSITY QUARTZ BEAM
• BUILT-IN UTILITY WORK STAND
BEFORE RETURNING THIS PRODUCT FOR ANY REASON,
PLEASE CALL TOLL FREE 866-584-5504
USER’S MANUAL &
WARRANTY INFORMATION
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY,
OPERATION, MAINTENANCE AND STORAGE OF THIS PRODUCT. READ
CAREFULLY BEFORE USE, AND RETAIN FOR FUTURE REFERENCE.
4140 S.W. 30th Ave., Ft. Lauderdale, FL 33312 U.S.
Toll Free: 866-584-5504
1
5.1 AC RECHARGE
WARNING: Use the supplied DC recharge adapter, do not substitute.
During Recharge:
DC recharge requires the use of the supplied DC recharge adapter.
1. Connect the DC recharge adapter’s DC plug to a 12 volt DC source.
2. Plug the adapter’s connecter into the recharge port located on the back of the unit.
3. Recharge for 5 hours maximum.
a) Never turn on while charging.
b) Make sure the AC power source is 120 volts, 60 Hz.
c) After recharge – disconnect cord and wait 5 minutes before use.
5.2 CHARGING INDICATORS
4. After recharge, disconnect the barrel connector from the recharge port and store the
adapter.
Unit includes charging indicator LED’s that display battery level of charge any
time during operation or storage by simply turning ON the area light. LED’s
willl light under the following conditions:
1. Automatically during AC recharge.
2. During area light operation.
6. PERIODIC MAINTENANCE
All batteries lose charge over time, especially when they are warm. AC recharge is rec-
ommended every two months, when not in frequent use. Use the AC recharger and
charge for the recommended time. If the unit gets dirty gently clean the outer surface of
the spotlight unit with a soft cloth moistened with a mild solution of water and detergent.
Periodically inspect the condition of recharge adapters, connectors, and wires. Replace
any components that may have become worn or broken.
During AC recharge green LED will blink when charging is complete. Wait 5
minutes after disconnecting charger to operate unit.
7. PARTS REPLACEMENT
FIGURE 2 - AC CHARGER
Three parts are replaceable by users. The quartz halogen bulb and sealed lead acid battery
are proprietary and are available through Vector Products, Inc.. A substitute 12 volt H3 100
watt bulb may be used instead of a Vector bulb. These can also be purchased from popular
automotive parts suppliers nationwide. The DC charging adapter fuse is replaceable.
Contact Vector Products, Inc.’s Technical Support Department for replacement parts and any
additional information that you may need. They may be reached toll free 866-584-5504.
7.1 DC PLUG FUSE REPLACEMENT
The fuse in the DC plug protects the charging circuit of the DC recharge adapter. If there
is no slight warming of the DC plug during recharge, you should suspect that 12 volts
DC is not powering the plug or the fuse is opened.
To replace the fuse:
1. Unscrew the end cap of the DC plug (counterclockwise).
2. Remove spring center contact and fuse.
3. Check fuse with a continuity checker.
4. If blown, locate replacement fuse with same type and rating.
5. Replace the fuse, spring, contact and end cap.
6. Screw end cap clockwise until it is finger tight-do not over-tighten.
7. Check for proper operation of DC charging adapter.
7.2 SPOTLIGHT BULB REPLACEMENT
WARNING: Use the supplied AC recharge adapter; do not substitute. AC recharg-
ing requires the use of the included AC charger/adapter that supplies
12 volts DC.
1. Connect the AC charger to an AC power source.
2. Plug the adapter’s barrel connecter into the AC recharge port located near the
handle.
3. Recharge for 18 hours maximum.
4. After recharge, disconnect the barrel connector from the recharge port and store the
adapter.
5.3 DC RECHARGE
To replace the H3 type 12 volt bulb, you will need a small Phillips-head type screwdriver
and a replacement bulb.
a) Maximum charge - 5 hours
b) After recharge – disconnect cord and wait 5 minutes before use.
REFLECTOR
FIGURE 3 - DC CHARGER
FIGURE 4 - LENS ASSEMBLY
LENS
RUBBER BEZEL
Make sure the DC source (jump starter, battery pack, vehicle accessory socket, etc) is
12 volt DC. The DC source should be able to supply at least 10 amps at 12 volt DC.
“O” RING
PHILLIPS
HEAD SCREWS
5
4
4. Note polarity of battery. Note which color wire is on which terminal.
5. Disconnect the wires from the battery and set the battery aside.
FIGURE 5 - BULB ASSEMBLY
BULB
METAL PRONGS
PHILLIPS HEAD SCREW
6. Connect the replacement battery, making sure the correct color wires are on the new
battery terminals. Make sure the polarity of battery is correct.
METAL PRONGS
WARNING: Incorrectly connected wires will damage the battery and recharge
adapter, double check battery polarity before reassembly.
CAUTION: Incorrectly connected wires will allow the spotlight to operate normally,
however, when recharge adapters are connected, there will be damage to
the battery and recharge adapters. Double check battery polarity before
reassembly!
PHILLIPS HEAD SCREW
REFLECTOR
Bulb life can be shortened by installing a bulb with dirt or fingerprints on it. During
installation, avoid touching the glass part of the bulb (see Figure 4 and 5 for details).
1. Disconnect the unit from charging adapter.
2. Pull off the rubber bezel to reveal two small Phillips-head screws.
3. Using the screwdriver, remove (counterclockwise) the two screws. Set them aside.
4. Lift off the retaining ring, glass, and rubber ring and set them aside.
5. Carefully remove the reflector and bulb assembly.
7. Replace handle, in one half of the housing body. Make sure wires and connectors
do not touch.
8. Place other half of housing body into position and replace screws (clockwise). Do
not overtighten.
9. Follow steps 13 through 19 for bulb replacement to reassemble reflector, rubber “O”
ring, glass, retaining ring and rubber bezel. Charge the new battery using AC
recharge adapter for a minimum of 20-25 hours initially, then 18 hours thereafter.
SAFE BATTERY DISPOSAL
6. Disconnect the bulb wire from the red power wire and set the burned out bulb
Contains a maintenance-free, sealed, non-spillable, lead acid battery, which must be
disposed of properly. Recycling is required, contact your local authority for information.
Failure to comply with local, state and federal regulations can result in fines or impris-
onment.
BATTERY DISPOSAL WARNING
• Do not dispose of the battery in fire as this may result in an explosion
aside.
7. Unsnap the hairpin retaining wires from the reflector’s flange.
8. Using the screwdriver, loosen the retaining screw to remove the bulb from the
reflector (no need to completely remove this screw).
9. Lift out the bulb and the attached wire.
10. Insert the replacement bulb into the reflector’s flange.
11. Put back and secure the hairpin retaining wires.
12. Connect the bulb power wire to the red power wire.
13. Tighten the retaining screw on the flange.
14. Place the reflector in position in the body of the spotlight.
15. Replace the rubber “O” ring in the groove around the perimeter of the reflector.
16. Replace glass and retaining ring so that the screw holes are aligned.
17. Secure retaining ring with two screws.
• Before disposing of the battery, protect exposed terminals with
heavy-duty electrical tape to prevent shorting (shorting can
result in injury or fire)
• Do not expose battery to fire or intense heat as it may explode
• For more information on recycling this battery, call toll-free
877-288-7722
8. SPECIFICATIONS
Spotlight Bulb........................................12 volt, H3 series, 100 watt quartz halogen
Battery..................................................Maintenance free, sealed lead acid, 12 volt
18. Replace rubber bezel.
19. Operate switch to ensure proper operation of spotlight.
7.3 REPLACING THE BATTERY PACK
T
he sealed lead acid battery has a life of several years, if recharged promptly after each
use. When a fully charged battery only provides about ten minutes or less of spotlight
operation, it should be replaced with a new one. To replace the battery, you will need
a narrow shaft Phillips-head screwdriver and a replacement battery. The battery pack
can be replaced by doing the following:
1. Complete the bulb replacement steps through step 4, to remove the reflector
assembly.
2. Remove all the Phillips-head screws (counterclockwise) that fasten the two halves of
the housing body.
3. Separate the two body halves and carefully pop out the handle.
WARNING: DO NOT ALLOW BARE WIRES OR CONNECTORS TO CONTACT
EACH OTHER; DANGEROUS SPARKING CAN OCCUR.
7
6
1 YEAR LIMITED WARRANTY PROGRAM
This limited warranty program is the only one that applies to this product, and it sets forth all
the responsibilities of Vector Products, Inc., regarding this product. There is no other war-
ranty, other than described herein.
This Vector Products, Inc. product is warranted, to the original purchaser only, to be free of
defects in materials and workmanship for one year from the date of purchase without addi-
tional charge. The warranty does not extend to subsequent purchasers or users. Vector
Products, Inc. will not be responsible for any amount of damage in excess of the retail pur-
chase price of the product under any circumstances. Incidental and consequential damages
are specifically excluded from coverage under this warranty.
This product is not intended for commercial use. This warranty does not apply to accessories
or damage to units from misuse or incorrect installation. Misuse includes wiring or connect-
ing to improper polarity power sources.
RETURN/REPAIR POLICY: Defective products, other than accessories, may be returned
postage prepaid to Vector Products, Inc.. Any defective product, other than accessories, that
is returned to Vector Products, Inc. within 30 days of the date of purchase will be replaced
free of charge. If such a product is returned more than 30 days but less than one year from
the purchase date, Vector Products, Inc. will repair the unit or, at its option, replace it free of
charge.
If the unit is repaired new or reconditioned replacement parts may be used at Vector
Products, Inc.’s option. A unit may be replaced with a new or reconditioned unit of the same
or comparable design. The repaired or replaced unit will then be warranted under the terms
of the remainder of the warranty period. The customer is responsible for the shipping
charges on all returned items after 30 days. During the warranty period, Vector Products,
Inc. will be responsible for the return shipping charges.
LIMITATIONS: This warranty does not cover accessories, bulbs, fuses and batteries, defects
resulting from normal wear and tear (including chips, scratches, abrasions, discoloration or
fading due to usage or exposure to sunlight), accidents, damage during shipping to our serv-
ice facility, alterations, unauthorized use or repair, neglect, misuse, abuse, failure to follow
instructions for care and maintenance, fire, flood and Acts of God.
If your problem is not covered by this warranty, call our Technical Support Department
954-584-4446 or toll free 866-584-5504 for general repair information and charges if
STATE LAW RIGHTS: This warranty gives you specific legal rights. Some states do not allow
limitations on how long an implied warranty lasts or the exclusion or limitation of incidental
or consequential damages, so the exclusions or limitations stated herein may not apply.
This warranty gives the purchaser specific legal rights; other rights, which vary from state to
state, may apply.
TO REQUEST WARRANTY SERVICE FOR THIS PRODUCT: Contact Vector Products, Inc.
Technical Support by telephone, fax or mail. We suggest that you keep the original pack-
aging in case you need to ship the unit. When returning a product, include your name,
address, phone number, dated sales receipt (or copy) and a description of the reason for
return and product serial number. After repairing or replacing the unit, we will make every
effort to return it to you within four weeks.
WARRANTY ACTIVATION: Please complete Warranty Activation Card and mail to Vector
Products, Inc.. Enter “VEC141” as Model and “2,000,000 Power Series” as Product Type.
All Vector Products, Inc. products must be registered within 30 days of purchase to activate
this warranty. Mail the completed registration card, along with a copy of the original sales
receipt to:
ATTN.: CUSTOMER SERVICE / VECTOR PRODUCTS, INC.
4140 S.W. 30TH AVE., FT. LAUDERDALE, FL 33312 U.S.
• TOLL FREE: 866-584-5504 • FAX: 954-584-5556.
YOU MAY ALSO CONTACT US AT OUR WEBSITE WWW.VECTORMFG.COM.
WARRANTY IS NON-TRANSFERABLE AND NON-REFUNDABLE.
DS070406
8
|