VP02
IMPORTANT SAFETY INSTRUCTIONS
CAUTION:
• TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
DISMANTLE. THERE ARE NO SERVICEABLE PARTS INSIDE.
• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
The exclamation point within an equilateral triangle alerts
the user to the presence of important operating and
maintenance instructions in this owner’s guide.
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR
PERSONAL INJURY:
• Turn off/unplug and allow to cool before replacing bulb or cleaning.
• Light bulbs get HOT quickly! Do not touch the bulb while the lamp is
on.
• Do not look directly at the lighted bulb.
• Do not operate the lamp in close proximity to flammable or
combustible vapors, such as aerosol (spray) products or where
oxygen is being administered.
• Use only the type of bulb and maximum wattage indicated by
Verilux®.
• Never cover the lamp when it is in operation.
2
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions – before using this lamp.
2. Keep these instructions – for future reference.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this lamp in damp/humid or wet locations.
6. For indoor use only.
7. Clean only with dry cloth.
8. Do not block any ventilation openings.
9. Do not place near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
10. Do not defeat the safety purpose of the polarized plug. A polarized
plug has two blades with one wider than the other. The wider blade
is provided for your safety. If the provided plug does not fit in your
outlet, consult an electrician for replacement of the obsolete outlet.
11. Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where it exits from
the lamp.
12. Only use attachments/accessories specified by the manufacturer.
13. Unplug this lamp during lightning storms or when unused for long
periods of time.
14. If the lamp has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have
fallen onto the lamp, the lamp has been exposed to rain or moisture,
does not operate normally, or has been dropped, it should not be
operated. There are no user serviceable parts within this lamp.
SAVE THESE INSTRUCTIONS
3
GENERAL PRECAUTIONS
• Do not use with power supply voltage other than 120V AC
• Avoid placing the lamp in areas that are dusty, humid/moist, lack
ventilation, or are subject to constant vibration.
• Not for use with light dimmers, timers, motion detectors, voltage
transformers, or extension cords.
• Do NOT use lubricating agent in bulb assembly.
• The light bulb may become loose during transit. To reinstall the light
bulb, see the bulb installation instructions on page 8.
• Close supervision is recommended when this lamp is used by or
near children, or others who may not understand the need for these
precautions. Do not leave the lamp unattended during use.
This product may cause interference with radios, cordless
telephones, or devices that use a wireless remote control,
such as televisions.
This lamp has been tested and found to comply with Part 18 of the
FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This lamp
generates, uses, and can radiate radio frequency energy and, if
not used in accordance with the instructions, may cause harmful
interference to radio communications. If interference occurs try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the lamp and receiver.
• Connect the lamp into an outlet on a circuit different from that to
which the receiver is connected.
• Move the lamp out of the line of sight of the remote control receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Note: This product may cause interference to radio equipment
and should not be installed near maritime safety communications
equipment or other critical navigation or communication equipment
operating between 0.45-30 MHz.
4
SET-UP INSTRUCTIONS
Unpacking
Please remove all packaging material. Check the carton for the items
pictured below:
Note: For your convenience, the bulb has been pre-installed in the
socket. However it may have loosened during transit. Please check to
be sure it is fully seated in the socket (see page 8)
5
SET-UP INSTRUCTIONS
Attaching the Parabolic Grid Diffuser
1. Remove protective packing from bulb.
2. Remove grid diffuser from protective plastic bag.
3. Insert plastic pegs at bottom of grid diffuser into openings near bulb
socket and snap tab into place.
TAB
4. Plug lamp into a standard 110-120V outlet, simply open the lamp
to switch it on and begin enjoying the benefits of Verilux® Natural
Spectrum® light!
Note: please allow a few minutes for the bulb to warm up to full
illumination.
Note: if bulb does not illuminate instantly, please refer to the
troubleshooting section of this manual.
6
CORD INSERTION
The lamp cord may be stored completely or partially within the
cavity at the back of the lamp.
To insert the cord, simply close the lamp, place it on a level surface
with its face down, turn the cord in a vertical position and insert the
cord into the back of the lamp until all or part of the length of the
cord is inserted.
When it is fully inserted, the plug may be locked into the slot at the
base of the insertion opening to avoid having the cord fall out during
transit.
7
BULB REPLACEMENT
Bulb removal & replacement
REMOVAL
1. Unplug lamp from power source.
2. To access the bulb, remove the grid diffuser by depressing the tab
and lifting it out (see page 6)
3. Firmly hold the bulb base (B) and pull bulb (C) from the socket in an
outward motion.
D
REPLACEMENT
1. Unplug lamp from power source.
2. Firmly hold base (B) and push
bulb (C) into the socket (A).
3. Be sure bulb is firmly seated in
the socket (see below) and
snapped into the metal
bulb clip (D).
C
B
A
4. Replace grid diffuser.
Correctly Seated Bulb
Incorrectly Seated Bulb
No Gap
Notice
Gap
8
TROUBLESHOOTING
Before requesting service on your Verilux® lamp please read the
following:
• Make sure all power connectors, cords, and plugs are inserted fully
and securely.
• Be sure the bulb is securely seated in the socket. (See page 8)
• Make sure there is power to the wall outlet or try another outlet – not
connected to a dimmer.
CARE & CLEANING
Your Verilux® lamp is made from high quality materials that will last for
many years with a minimum of care.
Clean only with a soft dry cloth – DO NOT USE SOLVENTS OR
CLEANERS CONTAINING ABRASIVES OR AMMONIA
WARNING: To prevent risk of shock or personal injury
when cleaning lamp, make sure you have turned off and
unplugged the lamp, and allow sufficient time for the bulb
to cool.
9
WARRANTY
Three-Year Limited Warranty
This limited warranty is provided by:
Verilux, Inc., Research Park, 9 Viaduct Road, Stamford, CT 06907
Verilux® warrants this product to be free of defects in materials and
workmanship for a period of three years from the invoice date of original
retail purchase. During the limited warranty period, Verilux® will, at its
option, repair or replace defective parts of this product, at no charge to
you, subject to the following limitations. This warranty does not include
any postage, freight, transportation, insurance, or delivery fee. This
limited warranty does not cover damage, defect, or failure caused by or
resulting from accidents, external destruction, alteration, modification,
abuse, misuse, or misapplication.
ATTENTION: When returning a product, be aware that damage during
shipping is the responsibility of the purchaser and will void any warranty
claim. We recommend that you insure the shipment by shipper when
returning this product or any parts. Be sure to return product in original
packaging.
Note: Verilux® recommends using a quality surge suppressor on all
electronics equipment. Voltage variations and spikes can damage
electronic components in any system. A quality suppressor can
eliminate the vast majority of failures attributed to surges and may be
purchased at electronics stores.
Due to ongoing improvements, actual product may have slight variations from the product
described in this manual.
10
340 Mad River Park, Waitsfield, VT 05673
1-888-544-4865
Printed in Taiwan for: Verilux, Inc.
© Copyright 2007 Verilux, Inc. All rights reserved.
VP02-MAN-Rev2
|