Used regularly, CleanWave®
eliminates up to 99.9% of
viruses, bacteria, allergens*,
dust mite and flea eggs
on surfaces.
VH01WW4
*Allergens due to mold and dust mites
SAVE THESE INSTRUCTIONS
1
12/2/09 9:12 AM
VH01_MAN_Rev1J1o.inbd#d: 0.000
Title: VH01 Manual
Version: VH01-MAN-Rev11
Date: 12/01/09
Contents
Warnings and Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
What’s Included. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Sanitizing Wand Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Sanitizing Wand Initial Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Charging the Wand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Sanitizing Wand Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Guidelines For Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Sanitizing Wand Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Sanitizing Wand Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3
3
12/2/09 9:12 AM
VH01_MAN_Rev1J1o.inbd#d: 0.000
Title: VH01 Manual
Version: VH01-MAN-Rev11
Date: 12/01/09
Warnings and Precautions
• To prevent fire or shock hazard, do not expose this product to rain or
excessive moisture.
• Do not leave product unattended while on.
• No serviceable parts. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus is damaged in any way, for
example the power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally or has been dropped.
• CleanWave® Wands should not be exposed to dripping or splashing and
objects filled with liquids, such as vases, should not be placed on or near
the apparatus.
• This unit should not be handled or used by children due to the danger of
accidental direct exposure to UV-C rays.
• Always direct the UV-C rays AWAY from the eyes and skin.
• Never use this device on pets.
• Care should be taken to prevent bulb breakage.
• Allow bulb to cool before replacing.
• Not intended for use on food.
WARNING: Direct exposure to this lamp can cause serious skin burn and eye
inflammation from short wave ultraviolet radiation. Radiation from these lamps
is harmful to the eyes and skin.
WARNING: Mercury Hazard. Be careful to not break the bulb during
replacement. UV-C bulbs contain a small amount of mercury, which can cause
injury if inhaled or ingested. For more information on clean up and disposal,
fact_sheet_mercury.pdf
CAUTION: Over time, UV-C light may degrade, discolor and/or bleach plastic
and rubber.
CAUTION: With prolonged or overexposure, UV-C light may degrade, discolor
and/or bleach fabrics and colors.
Ultraviolet (UV-C) Radiation Hazard
Over exposure will cause significant eye
damage and may cause skin damage.
Do not look into UV-C light source.
4
VH01_MAN_Rev11.indd
4
12/2/09 9:12 AM
Warnings and Precautions continued
FCC INFORMATION
This device complies with Part 18 of the FCC Rules. This product may
cause interference to radio communications and should not be installed near
maritime safety communications equipment or other critical navigation or
communication equipment operating between 0.45 - 30 MHz.
Warning: Changes or modifications to these units not expressly approved by
the party responsible for compliance could void the user’s authority to operate
equipment.
SAVE THESE INSTRUCTIONS
What’s Included
1. UV-C Sanitizing Wand
2. UV-C Sanitizing Wand Adapter
3. UV-C Sanitizing Wand Battery Pack
1.
2.
3.
5
5
12/2/09 9:12 AM
VH01_MAN_Rev1J1o.inbd#d: 0.000
Title: VH01 Manual
Version: VH01-MAN-Rev11
Date: 12/01/09
Introduction
Your new Verilux® CleanWave® UV-C Sanitizing Wand eliminates up to 99.9%
of viruses (including H1N1), bacteria (including MRSA), germs, mold, dust mite
and flea eggs.
We hope you enjoy this product and use it frequently. Your results will be
cumulative – your “kill rate” may be 90% during your first use on a
surface, then “90% of the remaining 10%” on your next use.
About Light and UV-C Light
Visible light is electromagnetic radiation in wavelengths visible to the human
eye. The wavelength of visible light, in nanometers, is about 400 nm to 750 nm.
A nanometer is one billionth of a standard metric meter.
Ultraviolet or UV light is the part of the electromagnetic spectrum – from about
10 nm to 400 nm – that contains frequencies just higher than visible light.
Above ultraviolet rays are X-rays. And above X-rays are gamma rays – the
highest – and highest energy – waves yet found.
Ultraviolet light was discovered by German physicist Johann Ritter. In 1801,
Ritter was experimenting with silver chloride, a chemical known to break down
when exposed to sunlight. He found that light at the blue end of the spectrum
increased the reaction.
Experimenting further, he discovered that the reaction was even more efficient
when exposed to radiation beyond blue – radiation that was invisible. He called
this new type of radiation ultraviolet, meaning “beyond the violet.” (Ultra comes
from the Latin for “beyond.”)
UV light is invisible to humans, but birds and some species of insects, snakes,
turtles and fish can see ultraviolet light.
UV light can be divided into various wavelength bands with differing
characteristics.
The Sun emits ultraviolet radiation in UV-A, UV-B and UV-C bands, but
because of absorption in the ozone layer, 99% of the ultraviolet radiation that
reaches Earth is “long wave” UV-A.
UV-A, also known as “black light,” creates fluorescent effects at your local
disco and “midnight bowling” sessions as UV light (which cannot be seen) is
absorbed by materials and re-emitted in the visible range.
UV-B “medium wave” rays both help and hurt. Too much UV-B exposure
causes sunburn and can damage human tissue. Too little UV-B exposure leads
to a lack of Vitamin D absorption in animals.
The higher-energy “short wave” UV-C band rays (100 to 280 nanometers) are
highly lethal to microorganisms. This range is known as the Germicidal Spectrum.
6
VH01_MAN_Rev11.indd
6
12/2/09 9:12 AM
Introduction continued
UV-C light sanitizes microorganisms and biological pollutants, including
viruses, bacteria, germs, mold, dust mite and flea eggs by penetrating their cell
membranes and attacking and deactivating their cellular DNA, stopping their
reproductive capabilities and killing them.
The scientific community has long known that UV-C light acts as a natural
sterilization system. Hospitals, food processing facilities, scientific laboratories,
water treatment plants and air-handling systems use UV-C light to eliminate up
to 99.9% of contaminants and germs.
The Verilux® CleanWave® Wand and Travel Wand provide that same UV-C
ultraviolet technology for use in your home and on the road.
The “Ultraviolet” article at Wikipedia (http://en.wikipedia.org/wiki/Ultraviolet)
offers a wealth of additional information and a comprehensive list of “See Also”
links and References.
Benefits of Using UV-C Light
• No Chemicals.Your home may contain more deadly chemicals than
laboratories did 50 years ago. With Verilux’s CleanWave Technology, you
can sanitize surfaces effectively and safely without chemicals and chemical
residues. The CleanWave eliminates up to 99.9% of bacteria, viruses,
germs, fungus, allergens* and mold with no chemical residue.
• Sanitizing with UV-C light means you don’t need harsh chemicals that
pollute our water and add unnecessary product packaging to our landfills.
Reduced production of household cleansers means fewer chemicals in our
environment and reduced fuel expenditures for transporting them to the
marketplace.
• Odor elimination. Bedding and couches will smell and feel fresh with
consistent use of the Sanitizing Wand. Because CleanWave eliminates
biological material that causes odors, musty smells and pet odors are
virtually eliminated.
*Allergens due to mold and dust mites
7
7
12/2/09 9:12 AM
VH01_MAN_Rev1J1o.inbd#d: 0.000
Title: VH01 Manual
Version: VH01-MAN-Rev11
Date: 12/01/09
Sanitizing Wand Features
Your new Verilux® CleanWave® Sanitizing Wand eliminates up to 99.9% of
germs, viruses, bacteria and mold on surfaces throughout your home. Use
regularly on surfaces to help keep your home sanitized without the risk of
chemical contamination.
• A powerful Ultraviolet (UV-C) illumination system that eliminates up to 99.9%
of viruses, germs, mold, dust mite and flea eggs on surfaces.
• Removes odors and dangerous allergens*.
• Perfect for use on bed clothes, in closets, as well as sofas and chairs.
• Portable, hand-held design is easy to operate.
• Built-in count up timer that displays the total time the Wand is used during
each session.
• Status Indicator that informs the user when the Wand is charging and when
it is on.
• The 6-inch UV-C light bulb allows wide coverage and makes sanitizing large
areas quick and easy.
*Allergens due to mold and dust mites
Safety Feature
An internal safety switch that will automatically turn off the Wand if the light
source is turned upward.
8
VH01_MAN_Rev11.indd
8
12/2/09 9:12 AM
Sanitizing Wand Initial Set-up
The battery pack is shipped separately from the Sanitizing Wand. Before using
the Sanitizing Wand, install the battery pack and fully charge the Wand.
Installing the Battery
Note: Be sure the charger is unplugged before installing a new battery pack.
1. Remove the gray handle faceplate on the
underside of the Wand using a screwdriver.
2. Attach the battery cable to the battery pack.
3. Place the battery pack in the battery
compartment.
4. Replace the faceplate. Tighten the screws.
Note: Used batteries should be disposed of
properly and never incinerated.
Note: The UV-C Sanitizing Wand contains a
rechargeable 4.8V Nickel Metal Hydride (NiMH)
battery pack made only by Verilux. Do not
attempt to replace with other brands. To order
a new battery, call Verilux customer service at
1-800-786-6850.
9
9
12/2/09 9:12 AM
VH01_MAN_Rev1J1o.inbd#d: 0.000
Title: VH01 Manual
Version: VH01-MAN-Rev11
Date: 12/01/09
Sanitizing Wand Initial Set-up continued
Charging the Wand
It takes approximately 14 hours to fully charge the
battery for the first time.
•
•
Connect the power adapter to the Wand.
Plug the power adapter into a 110V grounded
electrical outlet.
•
•
•
The status LED light is RED when the Wand is
charging.
The status LED light is GREEN when the Wand is fully
charged or in use.
After the first full charge, typical charging time is 8
hours under normal use. The Wand can be used for
1 1/2 hours when fully charged.You will not over-
charge the battery or otherwise harm the device by
keeping it connected to the charger between uses.
Low Battery Indication
When the battery is low and requires charging, the Wand will beep 10 times
and the red LED will flash 10 times.
LED Indicator Status:
• Flashing Red – Wand needs to be recharged.
• Red – the Wand is charging.
• Green – the Wand is fully charged or the Wand is on.
Sanitizing Wand Operation
Timer
During operation, a count-up timer shows total sanitizing
time. The display increments each second to 59, then
briefly displays the minutes elapsed before starting
another 59-second count-up. The “next” minute reached
is then shown briefly and the count-up begins again.
This cycle repeats for 99 minutes or until the Wand
requires charging.
To Start,
To see the current minute of sanitizing time, quickly
Press Until
Beep
press and release the blue button.
10
VH01_MAN_Rev11.indd 10
12/2/09 9:12 AM
Sanitizing Wand Operation continued
For example, if you’ve been using the Wand for 3 minutes and 20 seconds,
the Wand will show “20.” Press the button and the display will briefly show “03”
before continuing the by-the-second count-up to minute “04.”
Step by step:
1. To turn the Wand on, press the blue button until the Wand beeps – about
two seconds.
2. Lift your finger off the button. The Wand will turn on. The fluorescent bulb
may take another second or two to light.
3. The display window will show the count-up timer.
4. Begin sanitizing by holding the Wand as close as possible and no more than
one-half inch above the surface and moving Wand slowly side to side in a
12” (1 foot) area. The energy required to kill microorganisms is a product of
the light’s intensity and exposure time. The closer the Wand is to an object,
the more intense the energy. See Guidelines for Use (page 12) for more
specific information.
5. Move the Wand to next 12” (1 foot) area and continue sanitizing.
6. Repeat until you have completely sanitized your desired surface area.
7. When you have finished, press the blue button for three seconds. The Wand
will turn off.
NOTE: Be sure the Wand is facing downward, directly over your desired
sanitizing area. A safety switch will automatically turn off the UV-C light if the
Wand is tilted upward from the horizontal position. (The counter will not stop
during this temporary bulb safety shut-off.)
When the battery charge is low, the Wand will begin to beep and the red
indicator light will flash, indicating that the battery needs to be charged.
Using the Wand in Charging Mode
The Wand can be used in charging mode simply by connecting the power
adapter to the Wand and following the Operation instructions shown above.
11
11
12/2/09 9:12 AM
VH01_MAN_Rev1J1o.inbd#d: 0.000
Title: VH01 Manual
Version: VH01-MAN-Rev11
Date: 12/01/09
Guidelines For Use
The UV-C Sanitizing Wand is effective for eliminating germs, bacteria, viruses,
dust mite and flea eggs and mold from surfaces such as:
Bedding/mattresses
Brushes
Teakettle handles
Handrails
Earrings
Faucets
Bathroom fixtures
Curtains
Showers
Telephone handsets
Remote controls
Doorknobs
Chairs and sofa backs
Shoes
Computer keyboard and mouse
Baby changing stations
Children’s toys
Stuffed animals
Pet areas
Light switches
Steering wheel
Shopping cart handles
Airplane seat headrest
Hotel bedding
Alarm clock
Pet bedding
Auto seats
Wallets and purses
Cell phones
Furniture
Throw rugs
Music players
12
VH01_MAN_Rev11.indd 12
12/2/09 9:12 AM
Sanitizing Wand Bulb Replacement
Even with regular use, it is unlikely that you’ll ever need to replace the long-life
Verilux® bulb. If you do need to replace a bulb, use only Verilux bulbs. Use of a
non-Verilux bulb can result in damage to the Wand or the bulb.
To order a replacement bulb, use the Component Re-order form included
with this product. Or call Verilux Customer Service at 1-800-786-6850 or visit
Sanitizing Wand Troubleshooting
The Wand will not turn on
1. Try turning on the Wand while it is connected to the AC adapter and plugged
in. If it works, the battery may not be charged or connected properly.
2. Open battery compartment, disconnect battery clips for two seconds. Re-
connect clips; re-insert battery and cover. Try again.
No blue light underneath
• Bulb may be loose from shipping.
• Bulb may be broken or otherwise need replacing.
• Be sure Wand is facing downward directly over the surface being sanitized.
If the Wand is not operated in this manner, the internal safety switch will
prevent the Wand from operating. This feature is to help prevent direct
exposure to UV-C Light. Use caution when operating the Wand and do not
attempt to override this product feature.
WARNING: This unit should never be handled by children. Always direct the
UV-C rays AWAY from the eyes and skin.
13
13
12/2/09 9:12 AM
VH01_MAN_Rev1J1o.inbd#d: 0.000
Title: VH01 Manual
Version: VH01-MAN-Rev11
Date: 12/01/09
Technical Specifications
Environment
Operating Temperature: 15°C to 35°C (59°F to 95°F)
Storage Temperature: 0°C to 40°C (32°F to 104°F)
Relative Humidity: 5% to 95% non-condensing
UV-C Bulb
Replacement bulb: 4 Watt UV-C bulb (replace with Verilux® brand only)
Battery
4.8V, 1500mAh NiMH battery pack
Power Supply
Input Power: AC 100-240V, 50/60Hz, 0.5A
Output Power: DC 6.5V 1.5A
Class II
Conforms to IEC Class II safety requirements and the CEC Class IV efficiency
classification.
This Class II digital apparatus complies with Canadian ICES-003.
Warning: This product contains Mercury in the bulb, a substance known to
the state of California to cause birth defects or other reproductive harm. Use
caution when handling broken bulbs.
This device complies with the appliance efficiency regulations laid down by the
California Energy Commission.
14
VH01_MAN_Rev11.indd 14
12/2/09 9:12 AM
Warranty
One-Year Limited Warranty
ATTENTION! FOR REPAIR OR REPLACEMENT, ONCE OPENED, PLEASE DO NOT
RETURN THIS PRODUCT TO THE STORE WHERE IT WAS PURCHASED.
customer service department at 1-800-786-6850.
This limited warranty is provided by:
Verilux, Inc., 340 Mad River Park, Waitsfield, VT 05673
Verilux® warrants this product to be free from defects in material and workmanship for a period of one year from
the date of the original retail purchase. During the limited warranty period, Verilux, Inc. will, at its option, repair or
replace defective parts of this product, at no charge to the customer, subject to the following limitations. This limited
warranty does not include any postage, freight, insurance or delivery fees. This warranty does not cover damage,
defect or failure caused by or resulting from accident, external destruction, alteration, modification, abuse, misuse or
misapplication of this product.
If, during the first year of ownership, this product fails to operate properly, it should be returned as specified below:
Please pack the defective product in its original protective packing and box, with a copy of your name, address,
telephone number and sales receipt, along with $9.95 (check or money order to cover shipping and handling), and
send to:
For U.S. Postal Service Only:
Verilux Warranty
For Fed Ex & UPS Only:
Verilux Warranty
Service Center, c/o WTB
Service Center, c/o WTB
P.O. Box 119, West Redding, CT 06896
32 Henry Street, Bldg 17A, Bethel, CT 06801
Please allow 4-6 weeks before you receive the repaired or replaced product.
ATTENTION: When returning a product, be aware that damage during shipping is the
responsibility of the purchaser and will void any warranty claim. We recommend that
you insure the shipment by shipper when returning this product or any parts. Be sure to
return product in original packaging.
Note: Verilux recommends using a quality surge suppressor on all electronics equipment. Voltage variations
and spikes can damage electronic components in any system. A quality suppressor can eliminate the vast
majority of failures attributed to surges and may be purchased at electronics stores.
Due to ongoing improvements, actual product may have slight variations from the product described in this manual.
15
15
12/2/09 9:12 AM
VH01_MAN_Rev1J1o.inbd#d: 0.000
Title: VH01 Manual
Version: VH01-MAN-Rev11
Date: 12/01/09
340 Mad River Park, Waitsfield, VT 05673
Made in China
Printed in China for Verilux, Inc.
© Copyright 2010 Verilux, Inc. All rights reserved.
VH01-MAN-Rev11
VH01_MAN_Rev11.indd 16
12/2/09 9:12 AM
|