Professional Mixing Controller
OWNER'S MANUAL
VESTAX CORPORATION
1-18-6 Wakabayashi, Setagaya-ku, Tokyo 154-0023 Japan
Phone:03-3412-7011 Fax:03-3412-7013
Web:www.vestax.jp
VESTAX America
15320 Valley View Road Unit 9 La Mirada,CA 90638
Phone:1-562-623-9881,Fax:1-562-483-7304
Web:www.vestaxdj.com
(
)
VESTAX Europe Ltd.
Unit 5 Riverwey Industrial Park Alton, Hampshire GU34 2QL England, U.K
Phone:(0)1420-83000 Fax:(0)1420-80040
Web:www.vestax.co.uk
Vestax Technical Center of America
8489 W.Third Street Ste.1044 Los Angeles CA 90048
Phone:1-323-801-2111 Fax:1-323-801-2112
Vestax Europe Technical Support
Rheinstr.213 D-53332 Bornheim Germany
Phone:49(0)2222-95-23-72 Fax:49(0)2222-95-23-74
CAUT ION
RIS K OF ELECTRIC S HOCK DO NOT OP EN
CAUTl0 N：TO REDUCE THE RlS K OF ELECTRlC S HOCK
DO NOT REMOVE COVER（OR BACK）
NO US ER-S ERVICEABLE P ARTS INS IDE
REFER S ERVlCING T0 QUALIFIED S ERVlCE P ERS ONNEL
The lighting flash with arrowhead symbol，within an equilateral triangle，is intended
to alert the user to the presence of uninsulated“dangerous voltage”within the product's
enclosure that may be of sufficient magnitude to consitute a risk of electric shock to
persons．
The exclamation point within an equilateral triangle is intended to alert the user to the
pr esence of impor tant oper ating and maintenance（ser vicing）instr uctions in the
literature accompanying the appliance．
WARNING
T0 REDUCE THE RIS K 0 F FIRE 0 R ELECTRlC S HOCK，DO NOT EXP OS E
THIS AP P LIANCE T0 RAIN 0 R M0 IS TURE．
CAUTION：TO P REVENT ELECTRIC S HOCK,MATCH BLADE OF P LUG TO WIDE S LOT，FULLY INS ERT
ATTENTION：P 0 UR EVITER LES CH0 CS ELECTRIQUES ，INTRODUIRE LA LAME LA P LUS LARGE DE LA
FICHE DANS LA BORNE CORRES P 0 NDANTE DE LA P RIS E ET P 0 US S ER J US QU’AU F0 ND
IM P O R T A N T S A F E T Y IN S T R U C T IO N S
S A V E T H E S E IN S T R U C T IO N S
WARNING : When using electric products, basic precaution should always be followed,
including the following :
1. Read all the instructions before using the product.
8. The power - supply cord of the product should be unplugged
from the outlet when left unused for a long period of time.
2.
Do not use this product near water - for example, near a
bathtub, washbowl, kitchen sink, in a wet basement, or near a
swimming pool, or the like.
9.
Care should be taken so that objects do not fall and liquids are
not spilled into the enclosure through openings.
The product should be serviced by qualified service personnel
when ;
3.
4.
10.
This product should be used only with a cart or stand that is
recommended by the manufacturer.
This product, either alone or in combination with an amplifier
and headphone or speakers, may be capable of producing
sound levels that could cause permanent hearing loss. Do not
operate for a long period of time at a high volume level or at a
level that is uncomfortable. Without. you should consult an
audiologist.
A. The power - supply cord or the plug has been damaged ;
B. Objects have fallen, or liquid has been spilled into the
product ; or
C. The product has been exposed to rain ; or
D. The product does not appear to operate normally or
exhibits a marked change in perfromance ; or
E. The product has been dropped, or the enclosure damaged.
5.
6.
The product should be location or position does not interfere
with its proper ventilation.
The product should be located away from heat sources such as
radiators, heat registers, or other products that produce heat.
11. Do not attempt to service the product beyond that described in
the use - maintenance instructions. All other servicing should
be referred to qualified service personnel.
7. The product should be connected to a power supply only of the
type described in operating instructions or as marked on the
product.
2
FUNCTIONS
TOP PANEL
MICROP HONE AND �
S UBINP UT S ECTION
P ROGRAM �
INP UT S ECTION
MAS TER �
S ECTION
LINE 4 IN
PGM 1
SUB
PGM 2
INPUT
MASTER
+8
CUE
INPUT
INPUT
+8
+5
+3
+1
0
L
R
PHONO 1
LINE 2
PHONO 2
LINE 4
PHONO 3
LINE 6
+5
+3
+1
0
LINE 1
LINE 3
LINE 5
MIC
TRIM
TRIM
TRIM
-1
-1
-3
-3
MIC-1
MIC-1
MIC-2
-5
-5
MIN
MAX
MIN
MAX
MIN
BAL
MAX
-7
-7
BAL
BAL
-10
-15
POWER
-10
-15
POWER
MIN
MIC-2
MAX
MAX
L
EQ
R
L
EQ
R
L
R
L
R
EQ
HI
HI
HI
EFFECT
SEND
MIN
-16dB
MID
+16dB
+12dB
+16dB
-16dB
MID
+16dB
+12dB
+16dB
-16dB
MID
+16dB
+12dB
+16dB
EQ
HI
MIN
RETURN
MAX
-16dB
+16dB
+16dB
-12dB
LO
-12dB
LO
-12dB
LO
MIN
MAX
ON
LO
-16dB
CUE
OFF
-16dB
-16dB
-16dB
EFFECT
EFFECT
EFFECT
EFFECT
MASTER
BAL
OFF
CUE
POST
ON
PRE
OFF POST
PRE
OFF POST
PRE
OFF POST
CUE
CUE
CUE
L
R
OFF
OFF
ON
OFF
ON
OFF
ON
SIGNAL
SIGNAL
SIGNAL
LEVEL
LEVEL
LEVEL
LEVEL
MIN
MAX
10
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
MONITOR
9
8
7
6
5
4
3
2
1
0
SPLIT CUE
ON
OFF
PHONES
LEVEL
IS OLATOR �
S ECTION
MIN
MAX
PHONES
IN
PGM1 ISOLATOR
PGM2 ISOLATOR
LO
MID
HI
LO
MID
HI
1
2
PHONES IN
8
3
PROGRAM INPUT SECTION
1
○ INPUT SELECTOR
PGM 1
Used to select input (2 line or 1 phono) to be sent to each PGM channel.
INPUT
PHONO 1
LINE 2
2
○ TRIM CONTROL
1
Adjusts the Input level of each channel. Set INPUT FADER to 7-8position. adjust
TRIM so that the INPUT LEVEL METER shows about 0dB.
LINE 1
3
○ BALANCE CONTROL
Adjusts the stereo balance for each PGM channel. Can be used for adjusting the
unbalanced stereo image caused by a strong anti-skating setting. Clockwise rotation
from center position increases the volume of R over L channel. A counter
clockwise rotation increases the volume of L channel over R.
2
3
MIN
MAX
BAL
4
○ EQUALIZER(HI,MID,LOW)
L
EQ
R
Adjusts the HI, MID, LOW frequencies for each PGM channel. Each band has
following specifications.
HI
HI
MID
LOW
8kHz ±16dB
500Hz ±12dB
80Hz ±16dB
-16dB
MID
+16dB
+12dB
+16dB
4
5
○ EFFECT SWITCH
This switch enables the signal from each programs to be sent to AUX send jack.
Different signal routes can be selected this switch to different positions.
P R E : The signal before the input fader (after the EQ) will be sent to AUX
output.
-12dB
LO
-16dB
POST : The signal after the input and cross fader will be sent to AUX
output.
OFF : No signal will be sent to AUX output.
EFFECT
5
6
PRE
OFF POST
6
○ CUE SWITCH
CUE
Used to send the signal from each program to monitor section for headphone
monitoring.
OFF
ON
SIGNAL
7
○ INPUT FADER
Used to adjust the Input level of each program. Usually set at the 7-8 position. This is
a detachable fader for the ease of replacement. Replace with the IF-175 when it is worn out.
LEVEL
10
9
8
7
6
5
4
3
2
1
0
8
○ CROSS FADER
When the Input level of PGM1 and PGM2 are properly set, PGM1 will be heard with
the cross fader set to the left side. PGM2 will be heard with the cross fader set to the
right side. When the cross fader is set in the center, both programs will be heard. This
is detachable fader for the ease of replacement with "CF-PCV" when it is worn out.
7
Ins e rt t he �
m ult i-c a ble c onne c t or
CF-PCV For
PMC SERIES ( PMC05ProII , PMC06ProA, etc)
S e t s ide s wit c h t o "P CV" pos it ion.
P MC CONNECTOR
S e t s wit c h t o "P MC" pos it ion
4
HOW TO CHANGE THE FADER UNIT
■HOW TO REMOVE THE TOP PANEL
■HOW TO CHANGE THE FADER UNIT
1
1
○ Remove each fader knobs and 10 screws which ○ Remove the screws on the fader panel.
fix the top panel.
2
○ Remove the fader unit from position in mixer.
2
○ Remove the top panel.
3
○ Carefully remove the multi-cable connector from
Drive r
fader unit.
4
○ Attach multi-cable connector
Drive r
to new fader unit.
5
○ P os ition the fa de r unit
ca re fully a nd s e cure
with screws.
Top pa ne l
Ma in pa ne l
MICROPHONE, SUB INPUT SECTION
LINE 4 IN
9
○ LINE INPUT JACK(LINE4)
L
R
9
Input connectors for line level equipment such as CD players,tape decks
,DATs, or MDs etc.
MIC
10
○ MIC INPUT JACK(MIC1,2)
10
Input jacks of mic1, mic2.
MIC-1
MIC-1
MIC-2
11
○ MIC LEVEL
Adjusts the input level from all of the microphone inputs.
12
○ MIC EQUALIZER(HI,LOW)
MIN
MIC-2
MAX
MAX
11
12
Adjusts the HI and LOW frequencies for all of the microphone input.
13
○ EFFECT SWITCH
MIN
Used when sending signal to the external effect processor connected to the
effect SEND/RETURN.
EQ
HI
-16dB
+16dB
+16dB
14
○ CUE SWITCH
Used to send the signal from the mic channel to the monitor section for
headphone monitoring.
LO
-16dB
EFFECT
13
14
OFF
CUE
POST
ON
OFF
5
■MASTER SECTION
15
○ MASTER OUT LEVEL METER
1 6
1 5
The LED level meters indicate the signal level of the line out.
MASTER
+8
CUE
+8
+5
+3
+1
0
+5
+3
+1
0
16
○ CUE LEVEL METER
The LED level meters indicate the signal level of PGM input selected by
CUE SWITCH.
-1
-1
-3
-3
17
○ EFFECT SEND LEVEL
-5
-5
Used to adjust the output level from EFFECT SEND JACK. The signal is
selected by the effect switch.
-7
-7
-10
-15
POWER
-10
-15
POWER
18
○ EFFECT RETURN LEVEL
L
R
Used to adjust the input level from the EFFECT RETURN JACK. This
EFFECT RETURN can be used as the sub line input.
EFFECT
SEND
19
○ EFFECT CUE SWITCH
1 7
Used to send the signal from EFFECT RETURN JACK to the monitor
section for headphone monitoring.
MIN
RETURN
MAX
1 8
1 9
20
○ MASTER BALANCE VOLUME
MIN
MAX
ON
CUE
OFF
Adjusts the signal balance of left to the right side of the outputs from the
OUTPUT jack on the rear panel.
MASTER
21
○ MASTER LEVEL VOLUME
BAL
Adjust the signal level output from the output jack on the rear panel.
2 0
2 1
L
R
22
○ SPLIT CUE SWITCH
LEVEL
When this switch is ON, the master signal is always heard through the
right earcup of the headphone. The CUE signal will be heard in the left
earcup when that input is selected by the CUE SWITCH (5, 14). This
enables both programs to be monitored simultaneously,thus assisting in
beat mixing.
MIN
MAX
MONITOR
SPLIT CUE
ON
OFF
2 2
2 3
PHONES
LEVEL
23
○ HEAD PHONE LEVEL
Adjusts the headphone output level.
MIN
MAX
24
○ HEAD PHONE JACK
PHONES
IN
Use this jack to connect the headphones the impedance 8ohm to 600ohm
can be used, 150ohm is recommended.
2 4
■ISOLATOR SECTION
25
○ HI SWITCH
Allows cutting off the sound of treble range. Sound volume will be cut
when the switch is set downwards. When the switch is put back, the output
volume returns to normal. Can be useful for cutting off the sound of the
cymbals or high hats for example.
PGM1 ISOLATOR
26
○ MID SWITCH
Allows cutting off the sound of the middle range. Sound volume will be cut
when the switch is set downward position. When the switch is put back, the
output volume becomes normal sound volume. Can be used for cutting off
vocal and melody from the source.
LO
MID
HI
2 6
2 5
2 7
27
○ LOW SWITCH
Allows cutting off the sound of the bass range. Sound volume will be cut
when the switch is set downward. When the switch is put back, the output
volume return to normal. Can be utilized for creating the effects of an
acapella.
6
REAR PANEL
3 1
2 8
AC100V
50 / 60Hz 20W
POWER
MADE IN CHINA SERIAL NO.
OUTPUT
MASTER OUT 1
EFFECT
SEND
PGM
LINE 6
2
SUB
PGM 1
LINE 2
ON
R
L
R
L
R
L
R
L
OFF
R
LINE 3
L
LINE 5
LINE 1
R
L
MASTER OUT 2
PHONO 3
PHONO 2
GND
PHONO 1
GND
RETURN
2 9
3 0
3 2
3 3
3 5
3 4
28
○ POWER SWITCH
33
○ PHONO INPUT JACK
The first LED of MASTER OUT LEVEL METER
that is located on the top panel is lit when on.
Input jack for PGM1,PGM2 and SUB channel
turntables.
29
○ AC POWER CABLE
Connect turntables equipped with the MM pick up
cartridge only.
30
○
OUTPUT JACK(1/4inch PHONE JACK, RCA
PIN JACK)
Connect to the input of power amplifier.
34
○ LINE INPUT JACK
Input connectors for the line level equipment such as
CD players, tape decks, DATs, MDs.
31
○ EFFECT SEND JACK
35
○ GROUND TERMINAL
Connect the SEND jacks to the input of an external
effector unit(Delay,Reverb etc)
Connect this terminal to the ground lead of the
turntable. This helps to reduce noise and hum.
32
○ EFFECT RETURN JACK
Connect the RETURN jacks to the output of the
effector.
SPECIFICATIONS
●NOMINAL INPUT LEVEL／IMPEDANCE
●FREQUENCY RESPONSE 20Hz～20kHz (＋0，－3dB)
●S/N RATIO
●DIMENSION (
●WEIGHT
－80dB
PHONO
LINE
－42dB／470k
－10dB／47k
－42dB／3.3k
－10dB／47k
)
290mm X94mm X 380mm
5kg
WXHXD
MIC
EFFECT RCV
●RATED OUTPUT LEVEL／IMPEDANCE
LINE OUT
－4dB／10KΩ
－10dB／10kΩ
－10dB／10kΩ
REC OUT
EFFECT SEND
May.2001 PCV-275 E2
Vestax Corporation
|