PROFESSIONAL SERIES
BUILT-INHOODS/VENTILATORSWARRANTY
ONEYEARFULLWARRANTY
Built-in hoods/ventilators, all of their component parts and accessories, except as detailed below*, are warranted to
be free from defective materials or workmanship in normal household use for a period of twelve (12) months from
the date of purchase. NOTE: Viking Range ventilator kits are designed specifically for use with Viking Range
hoods. Use of any non-Viking Range ventilator kits VOIDS the hood warranty. Viking Range Corporation,
warrantor, agrees to repair or replace, at its option, any part which fails or is found to be defective during the
warranty period.
*Glass (including light bulbs), painted, and decorative items are warranted to be free from defective materials or
workmanship for a period of ninety (90) days from the date of original retail purchase. ANY DEFECTS MUST BE
REPORTED TO THE SELLING DEALER WITHIN NINETY (90) DAYS FROM DATE OF ORIGINAL RETAIL
PURCHASE.
Viking Range Corporation
use and care manual
Viking Range Corporation uses the most up-to-date processes and best materials available to produce all color
finishes. However, slight color variation may be noticed because of the inherent differences in painted parts and
porcelain parts as well as differences in kitchen lighting, product locations, and other factors.
FIVE YEAR LIMITED WARRANTY
Any hood blower motor which fails due to defective materials or workmanship in normal household use during the
second year through the fifth year from the date of original retail purchase will be repaired or replaced, free of
charge for the part itself, with the owner paying all other costs, including labor.
LIFETIME LIMITED WARRANTY (Outdoor Models Only)
Any stainless steel part which rusts through due to defective materials or workmanship in normal use during the
second year through the useful lifetime of the unit from date of original retail purchase will be repaired or replaced
free of charge for the part itself, with the owner paying all other costs including labor.
This warranty extends to the original purchaser of the product warranted hereunder and to each transferee owner of
the product during the term of warranty.
This warranty shall apply to products purchased and located in the United States and Canada. Products must be
purchased in the country where service is requested. Warranty labor shall be performed by an authorized Viking
Range Corporation service agency or representative. Warranty shall not apply to damage resulting from abuse,
accident, natural disaster, loss of electrical power to the product by anyone other than an authorized Viking Range
Corporation service agency or representative. This warranty does not apply to commercial usage. Warrantor is not
responsible for consequential or incidental damage whether arising out of breach of warranty, breach of contract, or
otherwise. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you.
Owner shall be responsible for proper installation, providing normal care and maintenance, providing proof of
purchase upon request, and making the appliance reasonably accessible for service. If the product or one of its
component parts contains a defect or malfunction during the warranty period, after a reasonable number of
attempts by the warrantor to remedy the defects or malfunctions, the owner is entitled to either a refund or
replacement of the product or its component part or parts. Replacement of a component part includes its free
installation. Warrantor’s liability on any claim of any kind, with respect to the goods or services covered hereunder,
shall in no case exceed the price of the goods or service or part thereof which gives rise to the claim.
WARRANTY SERVICE: Under the terms of this warranty, service must be performed by a factory authorized Viking
Range Corporation service agent or representative. Service will be provided during normal business hours, and
labor performed at overtime or premium rates shall not be covered by this warranty. To obtain warranty service,
contact the dealer from whom the product was purchased, an authorized Viking Range Corporation service agency,
or Viking Range Corporation. Provide model and service number and date of original purchase. For the name of
your nearest authorized Viking Range Corporation service agency, call the dealer from whom the product was
purchased or Viking Range Corporation. IMPORTANT: Retain proof of original purchase to establish warranty
period.
built-in hoods
(indoor and outdoor models)
The return of the Owner Registration Card is not a condition of warranty coverage. You, however, should return the
Owner Registration Card so that Viking Range Corporation can contact you should any question of safety arise
which could affect you.
Any implied warranties of merchantability and fitness applicable to the above described hood or ventilator motors
are limited in duration to the period of coverage of the applicable express written limited warranties set forth above.
Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not
apply to you. This warranty gives you specific legal rights, and you may also have other rights which may vary from
jurisdiction to jurisdiction.
VIKING RANGE CORPORATION
111 Front Street • Greenwood, Mississippi (MS) 38930 USA • (662) 455-1200
Specifications subject to change without notice.
For more product information, call 1-888-VIKING1 (845-4641), or visit the Viking web site at
F1570F
(M1203VR)
Located to the left of the fan switches is the halogen light switch. This
controls the 50 watt halogen lights located in the front of the hood. The
halogen lights also have a switch which can be rotated in order to dim or
brighten the lights. Turn the dimmer control knob clockwise to brighten the
lights and counterclockwise to dim.
•Do not use caustic detergent to clean the filters. A caustic cleaner may
damage the finish.
•Do not take the baffle filters apart to clean them. It is not necessary and will
void the filter warranty.
When cleaning filters in 18” H. hoods, always remove the grease trough and
clean by placing in sink with hot soapy water.
Each 18” H. indoor hood will be equipped with one or two heat lamp
outlets. The switches to operate the heat lamps will be located on the right
end of the control panel. The 250 watt infrared bulbs are not included and
should be purchased locally. CAUTION: Do not place flammable material
on warming shelves when using heat lamps.
Heat Sensor Thermostat
Your hood is equipped with a heat sensor thermostat. The thermostat will
turn on or speed up the blower if it senses excessive heat above the cooking
surface. If the blower is OFF - it turns the blower ON to HIGH speed. If the
blower is ON at a lower speed setting - it turns the blower up to HIGH
speed. When the temperature level drops to normal, the blower will return
to its original setting. CAUTION: If the power to the hood is not
disconnected during cleaning, the heat sensor thermostat can cause the
blower to turn ON.
Baffle
Grease Trough
Filters
(18” H. Hoods only)
Charcoal Filter Maintenance (Recirculating Hoods Only)
Replace the charcoal filters every 6 months to 1 year depending on the
amount and type of cooking.
To replace, remove the baffle/charcoal
filter assembly and slide the charcoal
filter out of the channel and replace
with new one. Do not put the
charcoal filters in the dishwasher or
oven.
CAUTION
UNPLUG POWER CORDS FROM CONTROL PANEL
BEFORE CLEANING OR SERVICING HOOD.
Cleaning and Maintenance
Any piece of equipment works better and lasts longer when
maintained properly and kept clean. Ventilation equipment is no exception.
Your hood must be kept clean and maintained properly.
Replacement filters are available
through your local Viking Range
dealer or you can call the Viking
Online Store at 1-877-834-8222.
Cleaning the Baffle Filters
As air passes through a baffle filter, grease particles collect on the stainless
steel “U” shaped baffle channels and drip down into the bottom of the filter.
Baffle filters are extremely efficient when compared to mesh filters. The
power of the hood is increased as more air passes through a baffle filter than
with usually dirty mesh filters. The capture of grease is also superior as baffle
filters are almost universally required in commercial installations. The baffle
filters should be examined periodically to assure that all surfaces and parts are
clean. The filters can be washed in a dishwasher or in a sink with hot, soapy
water. Simple periodic cleaning will insure maximum filter effectiveness.
Cleaning the Hood Canopy
Finishes in enamel or stainless steel are highly resistant to damage or
discoloration due to grease, steam, and heat provided that reasonable care is
given to the equipment. The following suggestions will help you keep your
hood looking new. Do not allow an excessive accumulation of grease. For
best results, you should wipe your hood clean with a cloth dipped in warm,
soapy water. DO NOT USE ABRASIVE CLEANSERS, STEEL WOOL PADS, or
ABRASIVE CLOTHS.
DO NOT use cleaners that contain chlorides, the
chlorides in the cleaner could damage the stainless steel finish.
4
5
If necessary to scrape stainless steel to remove encrusted materials, soak the
area with hot towels to loosen the material, then use a wooden or nylon
Service Information
Do not use
spatula or scraper.
a metal knife, spatula, or any other metal tool
If your hood should fail to operate check to see if the the circuit breaker
is open, or if a fuse is blown?
to scrape stainless steel. Every three months give your hood a thorough
cleaning. On painted surfaces, use a new coat of wax. A good wax cleaner,
available at either a grocery or hardware store will do both jobs at once. On
stainless steel surfaces, use a good stainless steel cleaner and polish.
If service is required:
1. Call your dealer or authorized service agency. The name of
the authorized service agency can be obtained from the
dealer or distributor in your area.
2. Have the following information readily available:
a. Model number
b. Serial number
c. Date purchased
d. Name of dealer from whom purchased
3. Clearly describe the problem that you are having.
Renewing the Enamel Finish
If discoloration occurs, you should thoroughly polish the finish on your hood
to renew its gloss and luster and to remove any grease residue which may
have a yellowing effect. Use any good enamel polish, refrigerator polish, or
automotive polish. CAUTION: Do not use a porcelain cleaner or rough
abrasive cleaner.
Renewing the Stainless Steel Finish
Regular cleaning is the best way to assure that your stainless steel finish stays
bright and unscratched. Use lemon oil or stainless steel polish to coat and
protect stainless steel.
If you are unable to obtain the name of an authorized service agency, or
if you continue to have service problems, contact Viking Range
Corporation at (601) 451-4133 or write to:
Brass Parts
Caution: All brass special ordered parts are coated with an epoxy coating.
Do not use brass cleaners or abrasive cleansers on the brass option parts. All
brass body parts should be wiped regularly with hot soapy water. When hot
soapy water will not do the job, use every day household cleaners that are
not abrasive.
VIKING RANGE CORPORATION
PREFERRED SERVICE
111 Front Street
Greenwood, Mississippi (MS) 38930 USA
Record the information indicated below. You will need it if service is
Cleaning Ductless Venting Chamber
ever required.
The model and serial number for your hood is located
1. Remove the middle vent by gently raising up and pulling out.
2. Use the same cleaning directions as stated in “Cleaning the Hood
Canopy”.
behind the baffle filter on the left side panel in the lower right corner.
Model Number
Date of Purchase
Dealer’s Name
Address
Serial Number
Date Installed
3. After cleaning, replace the middle vent.
Replacing Light Bulbs
Halogen Lights
Use an oven mitt during bulb removal to protect your hand in case the bulb
breaks.
1) Unscrew halogen bulb.
2) Replace the bulb with a 120 volt, 50-watt halogen bulb.
If service requires installation of parts, use only authorized parts to
ensure protection under the warranty.
Infrared Heat Lamp
Use an oven mitt during bulb removal to protect your hand in case the bulb
breaks.
1) Unscrew infrared bulb from heat lamp socket.
2) Replace the bulb with an R40, 120 volt, 250-watt infrared bulb.
THIS MANUAL SHOULD REMAIN WITH THE HOOD FOR
FUTURE REFERENCE
6
7
|