Vision Fitness Elliptical Trainer X6200HRC DA User Manual

V I S I O N F I T N E S S  
A s s e m b l y  
G u i d e  
M O D E L S X 6 2 0 0 H R C / D A & X 6 0 0 0 D A  
D U A L - A C T I O N E L L I P T I C A L T R A I N E R S  
 
TOOLS & HARDWARE INCLUDED  
MM  
5 Allen Wrench  
BLUE BAG  
MM  
13 Wrench  
Screwdriver  
MM  
M8 x 45 Bolt  
Quantity: 2  
MM  
M8 x 80 Bolt  
Quantity: 4  
MM  
M8 x 13 Nylock Nut  
Quantity: 4  
MM  
5 L-Shaped Wrench  
MM  
MM  
BLACK BAG  
19 D x 440 L Rear Folding Axle  
Quantity: 1  
(not shown to scale)  
MM  
M8 x 16 Bolt  
3
Quantity: 4  
 
ORANGE BAG  
PINK BAG  
8 x 17 X 1.5T Washer  
Quantity: 2  
MM  
M8 x 16 Bolt  
16 x 22 x .3T Spring Washer  
Quantity: 2  
Quantity: 2  
8 x 15 X 2T Lock Washer  
Quantity: 4  
MM  
MM  
16 x 28 x 1.5T Washer  
Quantity: 2  
5/16” x 30 x 1.5T Washer  
Quantity: 2  
M8 x 60 Bolt  
M5 x 25 Bolt  
Quantity: 2  
Quantity: 1  
GREEN BAG  
MM  
MM  
M7 x 35 Bolt  
Quantity: 2  
M8 x 12 Bolt  
Quantity: 2  
MM  
MM  
M8 x 25 x 1.5T Washer  
Quantity: 2  
M16 x 22 x .3T Spring Washer  
Quantity: 2  
M8 x 13 Nylock Nut  
Quantity: 4  
M8 x 12 Bolt  
Quantity: 2  
MM  
13 Nut Caps  
M26 x 34 x .3T Spring Washer  
Quantity: 2  
M8 x 35 x 2T Washer  
Quantity: 2  
Quantity: 2  
 
STEP  
1
STEP  
1
BLACK BAG  
• Install the left and right stabilizers  
MM  
with the four bolts (M8 x 16 ), using  
MM  
the Blue 5 Allen wrench.  
• Cover both stabilizers with the  
included rubber boots.  
• Insert the rear folding axle shaft  
MM  
MM  
(440 L x19 D) into the rear tube.  
STEP  
ORANGE BAG  
2
STEP  
2
• Slide a spring washer (M16 x .3T)  
onto the right-hand side of the rear  
folding axle, followed by the right-  
hand pedal arm guide rail (the guide  
rails each have a blue indicator arrow  
printed on their sides; these arrows  
should face to the outside).  
• Slide a flat washer (M16 x 1.5T)  
onto the right-hand side of the rear  
axle, followed by a rear wheel.  
• Slide the large flat washer  
(5/16” x 1.5T) onto the right-hand  
side of the rear axle, and secure with  
MM  
a bolt (M8 x 16 ).  
• Repeat above steps to install left-  
hand pedal arm guide rail.  
STEP  
3
STEP  
3
BLUE BAG  
• Mount the rear pedal arms to the  
front pedal arms using four bolts  
MM  
MM  
(M8 x 80 ) and four 13 NyLock  
MM  
nuts, using the 13 wrench.  
• Install the foot toe pieces to the front  
MM  
pedal arms with two bolts (M8 x 45 )  
MM  
using the Blue 5 Allen wrench.  
5
 
STEP  
4
STEP  
PINK BAG  
4
X6000 only: Unfold the RPM sensor  
wire, located in the frame console  
mast bracket. Remove any kinks.  
All models: Slide the rubber console  
mast cover onto the bottom of console  
mast, and slide it up as far as it will  
go.  
X6000DA  
OR  
X6000 only: Holding the console  
mast above the frame bracket, guide  
the RPM sensor wire and lower  
magnet cable up through the console  
mast while simultaneously sliding the  
console mast onto the frame bracket.  
X6200HRC/DA  
All models: Bolt the console mast  
to the frame bracket with two bolts  
MM  
(M8 x 60 ), two flat washers  
(8 x 17 x 1.5T), and two lock washers  
(8 x 15 x 2T). Tighten with the Blue  
MM  
5
Allen wrench. Slide the rubber  
console mast cover back down over  
the bolt heads. X6000 NOTE: Be sure  
the RPM sensor wire exits through the  
small slot at the top right side of the  
the console mast.  
X6000 only: Mount console to  
console mast, using the two screws.  
Plug the RPM sensor wire into the  
back of the console, and feed the  
excess back down into the small slot  
in the console mast.  
X6000 only: Turn the tension knob  
to Level 15. Reach inside the console  
mast and connect the magnet cables.  
Turn the knob to Level 1 and mount the  
MM  
knob using a bolt (M5 x 25 ).  
X6200 only: Remove the four  
screws from the back of the console.  
Plug the wire connector from inside  
the mast into the console. The cable  
connector is slotted, so it may only be  
connected one way; do not force it!  
X6200 only: Mount the console to  
the mast using the four screws. Do not  
pinch the cable!  
All models: Bolt the water bottle  
cage to the console mast using the  
two bolts located in the mast.  
6
 
STEP  
GREEN BAG  
5
• Slide a large spring washer  
(M26 x 34 x .3T) onto the console  
mast axle. Locate and slide the right  
upper handlebar bracket onto the  
console mast axle and attach with a  
STEP  
5
MM  
washer (M8 x 35 x 2T) and 13  
MM  
NyLock nut, using the 13 wrench.  
MM  
Snap the plastic 13 nut caps over  
the nuts.  
• Slide a small spring washer  
(M16 x 22 x .3T) onto the lower  
pedal arm support, followed by the  
right lower arm. Attach with a washer  
(M8 x 25 x 1.5T) and bolt (M8 x 12),  
MM  
using the Blue 5 Allen wrench.  
• Pivot the lower arm and insert the  
top end into the upper handlebar  
bracket. Attach with bolts (M7 x 35)  
and (M8 x 12) through the side, and  
bolts (M8 x 16) from the front. Tighten  
MM  
using the Blue 5 Allen wrench.  
• Repeat the above steps to attach the  
left-hand upper and lower arms.  
the vision to succeed  
621-D East Lake Street  
P.O. Box 280  
Lake Mills. WI 53551  
fax 1.920.648.3373  
toll free 1.800.335.4348  
phone 1.920.648.4090  
2000 Vision Fitness. All Rights Reserved. 8.00 Part #Z60EP08-AG1801PRD  
AG18.01PRD  
REV1  
7
 

Timex Watch 201 095002 User Manual
Timex Watch 714 095005 01 User Manual
Toastmaster Toaster T2040WT User Manual
Toshiba CRT Television 32A32 User Manual
Tote Vision Computer Monitor LCD 1540HD User Manual
TP Link Switch 24+2 24+2G User Manual
Tricity Bendix Clothes Dryer TM 551 User Manual
Tripp Lite Computer Hardware P222 006 User Manual
Verizon Cell Phone SCHu320 User Manual
Vizio Universal Remote VUR8 User Manual