Waring Blender TG15 User Manual

TAILGATERBLENDER  
TG15  
For your safety and continued enjoyment of this product,  
always read the instruction book carefully before using.  
 
7. Do not let cord hang over edge of table or counter, or  
touch hot surfaces.  
8. Keep hands and utensils out of jar while blending, to  
prevent the possibility of severe personal injury and/or  
damage to the blender. A rubber spatula may be used,  
but must be used only when the blender is not running.  
9. Blades are very sharp. Handle carefully.  
ꢀ0. To avoid injury, never place blade assembly on the base  
unless container is properly attached.  
ꢀꢀ. Always operate blender with cover in place.  
ꢀ2. For blending hot liquids, see “Hot Blending  
Instructions,” next page.  
ꢀ3. Screw on base collar firmly when assembling container.  
Injury can result if moving blades accidentally become  
exposed.  
ꢀ4. Do not leave blender unattended while it is running.  
SAVE THESE INSTRUCTIONS  
2
 
IMPORTANT:  
HOT BLENDING INSTRUCTIONS  
To minimize possibility of being scalded when blending hot  
ingredients, the following precautions and procedures must  
be observed:  
ꢀ. Begin blending with no more than one cup (8 oz.) of  
ingredients.  
2. Before turning blender on, remove the center lid insert.  
This will allow venting of the rapidly heated and  
expanding air.  
3. Start blending on low speed.  
4. While blender is running, up to ꢀ½ cups (ꢀ2 oz.) of  
additional liquid can be added. Pour liquid slowly  
through the opening in the lid.  
OPERATING INSTRUCTIONS  
ꢀ. When placing the container on the unit base, make sure  
that the unit is turned off and is at a complete stop.  
Do not put the container on or take it off while the unit  
is running. Doing so may damage the drive shaft or  
blade assembly. For best results, do not fill container  
above 3-cup level.  
2. With the switch in the Off position, plug the blender  
into a ꢀ2-volt cigarette lighter receptacle.  
3. The Waring Pro® TailgaterBlender is ideal for blending  
ice drinks. For best results, keep the blades covered  
with liquid, turn the unit on, remove the lid insert, and  
feed the ice cubes slowly into the container. NOTE:  
Never use containers other than Waring Pro®  
Blender containers with your unit.  
4. For other blending tasks, put ingredients into container,  
then put the lid on firmly. Always add liquid ingredients  
first, unless otherwise specified in recipe. Always hold  
container with one hand while blending.  
3
 
HOW TO ASSEMBLE CONTAINERS WITH  
REMOVABLE BLADES  
Always wash and rinse container prior to initial use.  
ꢀ. Before starting, make sure that the blender cord is  
unplugged and that the switch is in the Off position.  
2. Refer to Figure ꢀ on page 5. The following points are  
important to note when putting together the container  
assembly:  
• Container gasket must be placed between blade  
assembly and container.  
• Collar must be threaded properly onto the blender  
container base, and securely tightened before placing  
food or liquid in the container.  
• To ensure proper assembly, place the blender  
container upside down and turn the collar  
counterclockwise until securely tightened.  
3. Place assembled blender jar on unit base so that it is  
firmly seated and not tilted to one side. Never place the  
collar or blade assembly on the unit base unless the  
container has been completely assembled and securely  
tightened.  
4
 
HOW TO DISASSEMBLE AND CLEAN  
CONTAINERS WITH  
REMOVABLE BLADES  
Always wash and rinse container  
immediately after use.  
ꢀ. Be sure the switch is in the  
Off position.  
2. Remove the container  
assembly from the unit base  
and empty the contents.  
3. To disassemble the Waring  
Pro® TailgaterBlender, turn  
container collar clockwise.  
4. The collar, blade assembly and  
gasket are dishwasher safe.  
The plastic container lid and  
insert must be washed by  
Fig.ꢀ  
hand. Allow all parts to air dry.  
5. Be certain all components are in the proper position  
when reassembling blender container and base.  
5
 
HOW TO CLEAN UNIT BASE  
ꢀ. To clean the unit base, unplug the power cord. Wipe the  
exterior surfaces with a soft cloth or sponge dampened  
with cleaning solution. Rinse with clean water. Do not  
immerse the base in cleaning solution or water. Wipe  
the base with dry towel.  
FUSE REPLACEMENT  
The plug on the blender power cord contains a replaceable  
cartridge fuse. To gain access to the fuse, push the metal  
tip of the plug inward as far as it will go, then turn it  
counterclockwise until it releases. Withdraw the tip, with  
the fuse attached, by pulling it straight out of the plug body.  
Replace fuse with one of same size and rating (ꢀ5 Amperes,  
32 Volts, Slow-Blow). Reassemble plug by reversing above  
procedure.  
6
 
©2008  
Waring Consumer Products  
Division of Conair Corporation  
ꢀ50 Milford Road  
Printed in USA  
TGꢀ5 Tailgater IB  
08WR204  
East Windsor, NJ 08520  
028340  
 

Teac CD Player CD 3000 User Manual
Topcom Network Router 874B User Manual
Toshiba Flat Panel Television TV 27A33 User Manual
Toshiba Laptop 5105 User Manual
Toshiba Projector TLP450U User Manual
Trion Air Cleaner FM 1000 User Manual
Tripp Lite TV Cables S404 006 User Manual
VTech Laptop 91 01256 043 User Manual
Waves Music Pedal GTR Solo User Manual
Weed Eater Lawn Mower 174193 User Manual