R
Please do not return product to retailer.
Por favor, no devuelva el producto al lugar de compra.
Veuillez ne pas retourner le produit au détaillant.
1--800--554--6723
Register your product online at:
Registre su producto en línea en:
Enregistrez votre produit en ligne à l’adresse :
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
810 EPT
WARNING:
Read and follow all Safety Rules and Operating Instructions be-
fore using this product. Read instructions carefully before assem-
bling. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. Antes de ensamblar el producto lea
cuidadosamente el instructivo. El no hacerlo puede resultar en le-
siones graves.
AVERTISSEMENT:
Veuillez lire le manuel d’instructions et bien respecter tous les
avertissements et toutes les instructions de sécurité. Bien lire les
instructions avant d’assembler l’outil. Tout défaut de le faire pour-
rait entraîner des blessures graves.
Poulan
7349 Statesville Road
Charlotte, NC 28269
Poulan
850 Matheson Blvd. West
Mississauga, Ontario L5V 0B4
115260526 Rev. 2 4/15/10 BRW
use in the presence of flammable liquids or
gases to avoid creating a fire or explosion
and/or causing damage to unit. Do not abuse
cord. Never carry the unit by the extension
cord or yank extension cord to disconnect
unit. To unplug, grasp the plug, not the cord.
Do not use cord as a handle, close a door on
cord, or pull cord around sharp edges or cor-
ners. Turn off all controls before unplugging.
Do not expose cords to heat, oil, or water. Do
not use with damaged cord or plug. If unit is
not working as it should, has been dropped,
damaged, left outdoors, or dropped into wa-
ter, return it to your authorized service dealer
for repair. Unplug the unit from the power
source when not in use, before servicing, and
when changing accessories and/or attach-
ments. Do not put any object into openings.
Do not use with any opening blocked; keep
freeof dust, lint, hair and anything that may re-
duce air flow.
Safety Hat
Hearing
Protectio
e
tection
Snug
Fitting
Clothing
Heavy Duty
Gloves
Safety
Shoes
Chaps
S Keep children, bystanders, and animals a
minimum of 50 feet (15 meters) away from
the work area. Do not allow other people or
animals to be near when starting or operat-
ing the unit. Do not let visitors contact unit or
extension cord.
S Use a voltage supply as shown on unit.
S Avoid dangerous environments. Do not use
in unventilated areas or where dust or ex-
plosive vapors can build up.
HA
S To reduce the risk of electrical shock, this
equipment has a polarized plug (one blade
is wider than the other) and will require the
use of a polarized extension cord. The ap-
pliance plug will fit into a polarized exten-
sion cord only one way. If the plug does not
fit fully into the extension cord, reverse the
plug. If the plug still does not fit, obtain a
correct polarized extension cord. A polar-
ized extension cord will require the use of a
polarized wall outlet. This plug will fit intothe
polarized wall outlet only one way. If plug
does not fit fully into the wall outlet, reverse
the plug. If it still does not fit, contact a quali-
fied electrician to install the proper wall out-
let. Do not change the equipment plug, ex-
tension cord receptacle, or extension cord
plug in any way.
S To reduce risk of electrical shock, use ex-
tension cords specifically marked as suit-
able for outdoor appliances having electri-
cal rating not less than the rating of unit.
Cord must be marked with suffix “W--A” (in
Canada “W”). Make sure your extension
cord is in good condition. Inspect extension
cord before useand replaceif damaged. Do
not use a damaged cord. Cord insulation
must be intact with no cracks or deteriora-
tion. Plug connectors must beundamaged.
The extension cord used to reach the pow-
er source must be heavy enough to carry
current from the power source the full length
of the extension cord to the unit. An under-
sized extension cord will cause a drop in
line voltage resulting in loss of power and
overheating. If in doubt, use the next heavi-
er gauge. The lower the gauge number, the
heavier thecord (seeSELECT AN EXTEN-
SION CORD in the OPERATION section).
S Do not use multiple cords.
50 feet
(15 meters)
DANGER: Do not
use near electrical
wires or power lines.
Keep pruner at least
30 feet (10 meters)
away from all power
lines.
S Do not handle or operate this unit when you
are fatigued, ill, or upset, or if you have taken
alcohol, drugs, or medication. You must be in
good physical condition and mentally alert. If
you have any condition that might be aggra-
vated by strenuous work, check with doctor
before operating this unit.
S Carefully plan your operation in advance.
Do not start cutting until you have a clear
work area, secure footing, and a planned
retreat path. Cluttered areas invite injuries.
If situations occur which are not covered in
this manual, use care and good judgment. If
you needassistance, contact your authorized
service dealer or call 1-800-554-6723.
ELECTRICAL SAFETY
(applies to all attachments)
WARNING:
Avoid a dangerous environment. To reduce
the risk of electrical shock, do not use in rain,
in damp or wet locations, or around swimming
pools, hot tubs, etc. Do not expose to snow,
rain, or water to avoid the possibility of electri-
cal shock. Do not use on wet surfaces. Do not
handle extension cord plug or unit with wet
hands. Avoid dangerous situations. Do not
S Keep the extension cord clear of operator and
obstacles at all times. Position cord so that it
will not be caught on branches.
S Tie cord to cord retainer and connect to re-
cessed plug as shown in this manual to pre-
3
vent damage to unit and/or extension cord
and to reduce the possibility of the extension
cord disconnecting from the unit during op-
eration. See ATTACH THE EXTENSION
CORD TO YOUR TRIMMER in the OPERA-
TION section.
S Do not attempt to repair unit. Inspect the insu-
lation and connectors on the powerhead and
extension cord before each use. If there is
any damage, do not use until damage is re-
paired by your authorized service dealer.
S Do not use the unit if the switch does not
turn the unit on and off properly. Repairs to
the switch must be made by your autho-
rized service dealer.
S Keep all parts of your body away from the
chain when unit is running.
S Do not operate pruner from a ladder or in a
tree.
S Do not use apruner tocut downtrees or any
portion of the tree trunk.
S Only use for pruning limbs or branches
overhead not greater than 6 inches (15 cm)
in diameter.
S Never standunder the limb you are pruning.
Always position yourself out of the path of
falling debris.
S Do not cut smallbrush andsaplings withthe
pruner. Slender matter may catch in the
chain and be whipped toward you, pulling
you off balance.
S Avoid unintentional starting of the unit. Nev-
er carry unit with your finger on the switch.
Be sure the switch is in the OFF position
and never touch the switch when connect-
ing extension cord.
S Make sure the chain will not make contact
with any object while starting the unit. Never
try to start the unit when the guide bar is in a
cut.
S Avoid any body contact with any grounded
conductor, such as metal fences, or pipes,
to avoid the possibility of electric shock.
S Ground Fault Circuit Interrupter (GFCI)
protection should be provided on circuit or
outlet to be used. Receptacles are avail-
able having built-in GFCI protection and
may be used for this measure of safety.
S Stop the motor immediately if you are ap-
proached.
DOUBLE INSULATION CONSTRUCTION
This unit is double insulated to help protect
against electric shock. Double insulation
constructionconsists of two separate“layers”
of electrical insulation instead of grounding.
Tools built with this insulation system are not
intended to be grounded. No grounding
means is provided on this unit, nor should a
means of grounding be addedto this unit. As a
result, the extension cord used with your unit
can be plugged into any standard 120 volt
electrical outlet. Safety precautions must be
observed when operating any electrical tool.
The double insulation system only provides
added protection against injury resulting from
an internal electrical insulation failure.
S Do not force pruner. It will do the job better and
safer at the rate for which it was intended.
S Do not put pressure onthe pruner at the end
of the cut. Applyingpressurecan cause you
to lose control when the cut is completed.
S Do not run the unit at high speed when not
pruning.
S Use the right tool, cut wood only. Don’t use
pruner for purpose not intended; for example,
don’t use pruner for cutting plastic, masonry,
non-wood building materials, etc.
S If you strike or become entangled with afor-
eign object, stop the unit immediately and
check for damage. Have any damage re-
paired by an authorized service dealer be-
fore attempting further operations.
S Do not operate a pruner that is damaged,
improperly adjusted, or not completely and
securely assembled. Always replace bar
and chain immediately if it becomes dam-
aged, broken or is otherwise removed.
S Always stop the unit when work is delayed or
when walking from one cutting location to
another. Stop the motor and make sure chain
has stopped moving before setting the unit
down.
S Inspect cords periodically and if damaged,
have repaired by an authorized service
dealer.
WARNING:
S Use only in daylight or good artificial light.
All electrical repairs to this unit, including hous-
ing, switch, motor, etc., must be diagnosed and
repaired by qualified service personnel. Re-
placement parts for a double insulated ap-
pliance must be recommended by the manufac-
turer. A double insulated appliance is marked
with the words “double insulation” or “double in-
sulated”. The symbol (square within a square)
may also be marked on the appliance. Fail-
ure to have the unit repaired by qualified service
personnel can cause the double insulation
construction to become ineffective and result in
serious injury.
KICKBACK
WARNING: Avoid kickback which
can result in serious injury. Kickback is the
backward, upward or sudden forward motion
of the guide bar occurring when the chain
near the upper tip of the guide bar contacts
any object such as a log or branch, or when
the wood closes in and pinches the chain in
the cut. Contacting a foreign object in the
wood can also result in loss of control.
S Rotational Kickback can occur when the
moving chain contacts an object at the upper
tip of the guide bar. This contact can cause
the chain to dig into the object, which stops
the chain for an instant. The result is a light-
ning fast, reverse reaction which kicks the
guide bar up and back toward the operator.
PRUNER SAFETY
S Do not operate a pruner with one hand. Seri-
ous injury to the operator, helpers, bystanders
or any combination of these persons may re-
sult from one-handed operation. A pruner is
intended for two-handed use.
4
S Pinch-Kickback can occur when the wood
closes in and pinches the moving chain in
the cut alongthetop of the guidebar and the
chain is suddenly stopped. This sudden
stopping of the chain results in a reversal of
the chain force used to cut wood and
causes the pruner to move in the opposite
direction of the chain rotation. The pruner is
driven straight back toward the operator.
S Pull-In can occur when the moving chain
contacts a foreign object in the wood in the cut
along the bottom of the guide bar and the
chain is suddenly stopped. This sudden stop-
ping pulls the pruner forward and away from
the operator and could easily cause the oper-
ator to lose control of the pruner.
S Keep a good, firm grip on the pruner with
both hands when the unit is running and
don’t let go. A firm grip will help you reduce
kickback andmaintain control. Keep thefin-
gers of your left hand encircling and your
left thumb under the assist handle. Keep
your right hand completely around the trig-
ger handle whether your are right handed or
left handed.
S Stand with your weight evenly balanced on
both feet.
S Stand slightly to the left side of the pruner to
keep your body from being in a direct line
with the cutting chain.
KICKBACK SAFETY FEATURES
REDUCE THE CHANCE OF
WARNING: The following features
are included on your pruner to help reducethe
hazard of kickback; however, such features
will not totally eliminate this danger. As a
pruner user, do not rely only on safety de-
vices. You must follow all safety precautions,
instructions, and maintenance in this manual
to help avoid kickback and other forces which
can result in serious injury.
KICKBACK
S Recognize that kickback can happen. With
a basic understanding of kickback, you can
reduce the element of surprise which con-
tributes to accidents.
S Never let the moving chain contact any ob-
ject at the tip of the guide bar.
S Keep the working area free from obstructions
such as other trees, branches, rocks, stumps,
etc. Eliminate or avoid any obstruction that
your chain could hit while you are cutting.
When cutting a branch, do not let the guide
bar contact branch or other objects around it.
S Keep your chain sharp and properly ten-
sioned. A loose or dull chain can increase
the chance of kickback occurring. Follow
manufacturer’s chain sharpening and
maintenance instructions. Check tension
at regular intervals, but never with the motor
running. Make sure the bar clamp nut is se-
curely tightened after tensioning the chain.
S Begin and continue cutting at full speed. If
the chainis moving at aslower speed, there
is greater chance of kickback occurring.
S Cut one branch at a time.
S Use extreme caution when re-entering a
previous cut.
S Do not attempt cuts starting with the tip of
the bar (plunge cuts).
S Watch for shifting of wood or other forces that
could close a cut and pinch or fall into chain.
S Use the Reduced--Kickback Guide Bar and
Low--Kickback Chain specified for your unit.
S Reduced--Kickback Guide Bar, designed with
a small radius tip which reduces the size of
the kickback danger zone on the bar tip.
Reduced Kickback Symmetrical Guide Bar
Small Radius Tip
Symm
rge Radius Tip
S Low--Kickback Chain, designed with a con-
toured depth gauge and guard link which
deflect kickback force and allow wood to
gradually ride into the cutter. A low kickback
chain has met kickback performance require-
ments when tested on the representative
sample of the chain saws specified in ANSI
B175.1.
Contoured Depth Gauge
MAINTAIN CONTROL
Elongated Guard Link
Deflects
kickback force
and allows wood
Low---Kickback
to gradually ride
Chain
into cutter
Can Obstruct Material
Not a Low---Kickback Chain
LINE TRIMMER SAFETY
DANGER: Never use blades with line
trimmer attachment. Never use flailing de-
vices with any attachment. This attachment
(when used with supplied line trimmer attach-
ment) is designed for line trimmer use only.
Use of any other accessories with line trim-
mer attachment will increase the risk of injury.
5
MAINTAIN YOUR UNIT IN GOOD
WORKING ORDER
S Have all service performed by a qualified
service dealer with the exception of the
items listed in the maintenance section of
this manual.
S Maintain unit according to recommended
procedures.
WARNING: Trimmer line throws ob-
jects violently. You and others can be blinded/
injured. Wear safety glasses, boots, and leg
protection. Keep body parts clear of rotating
line.
S Make certain the chain and/or cutting head
stops moving when trigger switch is re-
leased.
S When using the trimmer attachment,
keep cutting line at proper length. Use
only 0.080″ (2 mm) diameter Poulan
brand line. Never use wire, rope, string,
etc.
Eye Protection
S Install required shield properly before using
the trimmer attachment. Use only specified
trimmer head and spool; make sure it is
properly installed and securely fastened.
S Never modify your unit in any way.
S Keep the handles dry, clean, and free from
oil and grease.
50 ft.
(15 meters)
Boots
Keep children, bystanders, and animals 50
feet (15 meters) away. If approached stop unit
immediately.
S Keep oil cap, screws, and fasteners se-
curely tightened.
S Keep chain sharp and clean for better and
safer performance.
S Follow instructions for lubricating and chang-
ing accessories and for changing trimmer
line.
WARNING: Inspect the area to be
trimmed before each use. Remove objects
(rocks, broken glass, nails, wire, etc.) which
can be thrown by or become entangled in line.
Hard objects can damage the trimmer head
and be thrown causing serious injury.
S Inspect unit before use. Replace damaged
parts. Make sure all handles, guards, and
fasteners are in place and securely fas-
tened. Parts that are damaged must be re-
paired or replaced by an authorized service
dealer. These include head parts that are
cracked, or chipped, guards, and any other
part that is damaged.
S Keep firm footing and balance. Do not over-
reach or use from unstable surfaces such as
ladders, trees, steep slopes, rooftops, etc.
S Keep all parts of your body away from cut-
ting head and spinning line.
S Keep the cutting head below waist level. Do
not raise handles above your waist. Cutting
head can come dangerously close to your
body.
S Use unit properly. Use only for trimming, edg-
ing, scalping, and mowing. Do not force unit.
It will do the job better and with less risk of in-
jury at the rate for which it was designed.
S When using the trimmer attachment, keep
cutting line at proper length. Use only 0.080″
(2 mm) diameter Poulan brand line. Never
use wire, rope, string, etc.
S Install required shield properly before using
the trimmer attachment. Use only specified
trimmer head and spool; make sure it is
properly installed and securely fastened.
S Cut from your right to your left. Cutting on
left side of the shield will throw debris away
from the operator.
S Check for damaged parts. Before further use
of the unit, a part that is damaged should be
carefully checked to determine that it will op-
erate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting and any other conditions that may
affect its operation. Any part that is damaged
should be properly repaired or replaced by an
authorized service dealer unless otherwise
indicated elsewhere in the instruction manual.
S Use only recommended attachments and re-
placement parts to avoid creating a hazard
and/or voiding warranty.
S When not in use, the unit should be stored in a
dry, high or locked-up place out of the reach of
children.
S When storing unit, unplug from the power
source and use a bar sheath when appropri-
ate.
TRANSPORTING AND STORAGE
S Stop the unit and disconnect the power
source when not in use.
S Carry the unit with motor stopped.
S Store unit indoors in a high, dry place out of
the reach of children. Store unit unplugged.
S Do not hang unit so that the trigger switch is
depressed.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of hand tools could
cause blood vessel or nerve damage in the
fingers, hands, and joints of people prone to
circulation disorders or abnormal swellings.
Prolonged use in cold weather has been
linked to blood vessel damage in otherwise
healthy people. If symptoms occur such as
numbness, pain, loss of strength, change in
skin color or texture, or loss of feeling in the
fingers, hands, or joints, discontinue the use
S Store the unit so the line limiter blade (on
underside of shield) cannot cause injury.
S Use only in daylight or in good artificial light.
S Use only for jobs explained in this manual
(or manuals for optional attachments).
6
of this tool and seek medical attention. An
anti--vibration system does not guarantee the
avoidance of these problems. Users who op-
erate power tools on a continual and regular
basis must monitor closely their physicalcon-
dition and the condition of this tool.
and discharge tubes free of debris which
can accumulate and restrict proper air flow.
S Never place any object inair intake opening
as this could restrict proper air flow and
cause damage to the unit.
S Never douse or squirt the unit with water or
any other liquid. Clean unit and labels with a
damp sponge. Keep handles dry, clean,
and free from oil and grease.
RECOMMENDED ATTACHMENTS
This model is equipped with a coupler which
enables optional attachments to be installed.
The optional attachments are:
S Never use for spreading chemicals, fertiliz-
ers, or other substances which may contain
toxic materials.
S To avoid spreading fire, do not use near leaf
or brush fires, fireplaces, barbecue pits,
ashtrays, etc.
MODEL:
Edger . . . . . . . . . . . . . . . . . . . . PP1000E
Cultivator . . . . . . . . . . . . . . . . . PP2000T
Blower . . . . . . . . . . . . . . . . . . . PP3000B
CULTIVATOR SAFETY
WARNING: Use of any other attach-
ments besides those listed above and the at-
tachment provided with this unit might present a
risk of injury to the operator or bystanders. Only
those attachments listed above and the attach-
ment provided with this unit have been tested for
use with this powerhead.
DANGER: RISK OF CUT. KEEP
HANDS AND FEET AWAY FROM TINES AND
CUTTING AREA. Rotating tines can cause se-
rious injury. Do not attempt to clear away cut
material or hold material to be cut when the mo-
tor is running. Make sure powerhead is stopped
and disconnected from power source when re-
moving jammed material from the tines. Do not
grab or hold attachment by the tines.
ADDITIONAL SAFETY RULES
FOR OPTIONAL ATTACHMENTS
WARNING: For each optionalattach-
ment used, read entire instruction manual be-
fore use and follow all warnings and instruc-
tions in manual and on attachment.
NOTE: Use the assist handle included with
your unit (as shown below) when operating
the following attachments.
WARNING: Rotating tines can cause
serious injury. Keep away from rotating tines.
Stop the unit and disconnect the power source
before unclogging tines or making repairs.
Assist Handle
BLOWER SAFETY
WARNING: Inspect the area to be
cultivated before starting the unit. Remove all
debris and hard and sharp objects such as
rocks, vines, branches, rope, string, etc.
S Hold the unit firmly with both hands
S Keep firm footing and balance. Do not over-
reach or stand on unstable surfaces.
S Look behind and use care when backing up.
S Keep all parts of your body away from the
tines.
WARNING: Never put hands or other
objects into blower housing to avoid serious
injury from rotating impeller.
WARNING: Inspect area before
starting unit. Remove all debris and hard ob-
jects such as rocks, glass, wire, etc. that can
ricochet, be thrown, or otherwise cause injury
or damage during operation.
S Inspect unit before each use for worn,
loose, missing or damaged parts. Do not
use until unit is in proper working order.
S Do not set unit on any surface except a clean,
hard area. Debris such as gravel, sand, dust,
grass, etc., could be picked up by the air in-
take and thrown out through discharge open-
ing, damaging unit, property, or causing seri-
ous injury to bystanders or operator.
S Never operate the cultivator without thetine
guard in place and properly secured.
S Keep the tines andguard clear of debris. Al-
ways wear gloves when servicing or clean-
ing the tines. The tines become very sharp
from use.
S Avoid heavy contact with solid objects that
might stop the tines. If heavy contact oc-
curs, stop the motor and inspect the unit for
damage.
S Never placeobjects insidethe blower tubes
or blower outlet. Always direct the blowing
debris away from people, animals, glass,
and solid objects such as trees, automo-
biles, walls, etc. The force of air can cause
rocks, dirt, or sticks to be thrown or to rico-
chet which can hurt people or animals,
break glass, or cause other damage.
S After striking a foreign object, stop the unit,
disconnect the power source and inspect
the cultivator for damage. Repair before re-
starting.
S Disconnect attachment from the drive mo-
tor before cleaning the tines with a hose and
water to remove any build--up. Oil the tines
to prevent rust.
S Check air intake opening and blower tubes
frequently, always with unit stopped and
power source disconnected. Keep vents
S Do not run unit at highspeed unless cultiva-
ting.
7
S Hold the unit firmly with both hands.
S Keep firm footing and balance. Do not over-
reach or stand on unstable surfaces.
S Throw away blades that are bent, warped,
cracked, broken or damaged in any other
way. Replace parts that are cracked,
chipped, or damaged before using the unit.
S Keep all parts of your body away from the
blade.
EDGER SAFETY
DANGER: RISK OF CUT. KEEP
HANDS AND FEET AWAY FROM BLADE
AND CUTTING AREA. Do not attempt to clear
away cut material when the blade is in motion.
Make sure switch is in the off position and the
power source is disconnected when removing
jammed material from the cutting blade. Do not
grab or hold unit by the cutting blade.Inspect
the area to be edged before each use. Re-
move objects (rocks, broken glass, nails,
wire, etc.) which can be thrown by the blade
or can wrap around the shaft.
S Keep blade guard in place and in good
working order.
S Always keep the wheel in contact with the
ground.
S Always push the unit slowly over the
ground. Stay alert for uneven sidewalks,
holes in the terrain, large roots, etc.
S To reduce the risk of fire, do not allow exces-
sive grass, leaves, or grease to accumulate
on the attachment.
WARNING: Inspect the area to be
edged before each use. Remove objects
(rocks, broken glass, nails, wire, etc.) which
can be thrown by the blade or can wrap
around the shaft.
S Blade rotates momentarily after the trigger
is released. The blade can seriously cut
you or others.
S Allow blade to stop before removing it from
the cut.
S Objects struck by the cutting member can
cause serious injuries to persons. The lawn
should always be carefully examined and
cleared of all objects prior to edging.
SAVE THESE INSTRUCTIONS
S Check air intake opening or vacuum tube(s)
frequently, always with engine stopped and
WARNING: Use of any other attach-
unit disconnected from power source. Keep
vents and tubes free of debris which can ac-
cumulate and restrict proper air flow.
PRUNER SAFETY
(RECIPROCATING BLADE)
ments not recommended in this manual may in-
crease the risk of injury to persons, fire, or elec-
trical shock. Use of attachments not covered
under the list of recommended attachments in
this manual have not been evaluated for use
with this powerhead by Underwriters Laborato-
ries (see RECOMMENDED ATTACHMENTS).
WARNING: The reciprocating blade
can cause severe injury. Inspect the unit be-
fore use. Do not operate unit with a bent,
cracked or dull blade. Keep away from the
blade.
WARNING: This unit is not designed
for use with a brushcutter attachment.
VACUUM SAFETY
WARNING: Inspect area before
starting unit. Remove all debris and hard ob-
jects such as rocks, glass, wire, etc. that can
ricochet, be thrown, or otherwise cause injury
or damage during operation.
WARNING: The reciprocating blade is
sharp. Do not touch. To prevent serious injury,
always stop engine and ensure blade has
stopped moving, disconnect unit from power
source, and wear gloves when changing or
handling the blade.
S Never place objects inside the vacuum
tube(s). Always direct the blowing debris
away frompeople, animals, glass, andsolid
objects such as trees, automobiles, walls,
etc. The forceof aircan causerocks, dirt, or
sticks to be thrown or to ricochet which can
hurt people or animals, break glass, or
cause other damage.
WARNING: A coasting blade can
cause injury while it continues to move after the
engine is stopped. Maintain proper control of the
unit until the blade has completely stopped mov-
ing. Keep hands, face and feet at a distance
from all moving parts. Do not attempt to touch or
stop the blade when it is moving.
S Never run unit without the proper equip-
ment attached. When using your unit as a
vacuum, always install vacuum tube(s).
8
WARNING: Never lean over dis-
charge chute. Rocks or debris could be
thrown into the eyes and face and cause seri-
ous injury or blindness.
WARNING: For additional information,
refer to the safety section of the instruction
manual supplied with your pruner attachment.
HEDGE TRIMMER SAFETY
WARNING: Inspect the area where
the unit is to be used. Remove objects that
couldbe thrown or damage the unit. Some ob-
jects may be hidden by fallen snow -- be alert
for the possibility.
DANGER: RISK OF CUT; KEEP
HANDS AWAY FROM BLADE -- Blade
moves momentarily after the trigger is re-
leased. Do not attempt to clear away cut ma-
terial when the blade is in motion. Make sure
the unit is disconnected from the power
source and the blade has stopped moving be-
fore removing jammed material from the cut-
ting blade. Do not grab or hold the unit by the
cutting blade.
S Direct material discharge away from glass
enclosures, automobiles, etc.
S Do not run motor at high speed while not re-
moving snow.
S Be attentive when using the snowthrower,
and stay alert for holes in the terrain and
other hidden hazards.
S Make sure the rotor will spin freely before
attaching the snowthrower to the power-
head.
Blades move
momentarily
after the
Allow blades to stop
before removing
them from the cut.
S If the rotor will not rotate freely due to frozen
ice, thaw the unit thoroughly before attempt-
ing to operate under power.
is
d.
S Keep the rotor clear of debris.
S Do not throw snow near other people. The
snow thrower could propel small objects at
high speed causing injury.
WARNING: Inspect the area before
starting the unit. Remove all debris and hard
objects such as rocks, glass, wire, etc. that
can ricochet, be thrown, or otherwise cause
injury or damage during operation.
S After striking a foreign object, stop the unit,
disconnect from the power source and in-
spect the snowthrower for damage and re-
pair if necessary before restarting unit.
S Never operate the snowthrower near glass
enclosures, automobiles and trucks.
S Never attempt to use the snowthrower on a
roof.
S Do not use a cutting blade that is bent,
warped, cracked, broken or damaged in any
other way. Have worn or damaged parts re-
placed by your authorized service dealer.
S Always keep unit in front of your body.
Keep all parts of your body away from the
cutting blade.
S Never operate the snowthrower near win-
dow wells, dropoffs, etc.
S Never discharge snow onto public roads or
near moving traffic.
S Clear snow from slopes by going up and
down; never across. Use caution when
changing directions. Never clear snow from
steep slopes.
S Let snowthrower run for a few minutes after
clearing snow so moving parts do not
freeze.
S Keep the cutting bladeand air vents clear of
debris.
SNOW THROWER SAFETY
WARNING: Keep hands and feet
away from the rotor when starting or running
the unit. Never attempt to clear the rotor with
the motor running. Stop the unit and discon-
nect from the power source before unclog-
ging snow or debris from discharge chute or
when adjusting vanes.
S Look behind and use care when backing
up. Exercise caution to avoidslipping or fal-
ling, especially when operating in reverse.
S Know how to stop quickly.
9
ASSEMBLY
1. Try on shoulder strapand adjust for fit and
balance before starting the unit or begin-
ning a cutting operation.
WARNING: If received assembled,
review all assembly steps to ensure your unit
is properly assembled and all fasteners are
secure.
2. Insert your right arm andhead throughthe
shoulder strap and allow it to rest on your
left shoulder. Make sure the danger sign
is centered on your back and the hook is
to the right side of your waist.
NOTE: A one-half twist is built in the shoul-
der strap to allow the strap to rest flat on the
shoulder.
3. Adjust the strap, allowing the hook to be
about 3 -- 6 inches (8 -- 15 cm) below the
waist.
4. Fasten the strap hook to the clamp lo-
cated between the trigger handle and the
assist handleand lift the tool to the operat-
ing position.
NOTE: It may be necessary to relocate the
shoulder strap clamp on the shaft for proper
balancing of unit.
Examine parts for damage. Do not use dam-
aged parts.
NOTE: If you need assistance or find parts
missing or damaged, call 1-800-554-6723.
TOOLS REQUIRED
S Hex wrench
S Chain adjustment tool (bar tool)
INSTALLING PRUNER OR LINE
TRIMMER ATTACHMENT
CAUTION: When removing or installing at-
tachments, place the unit on a flat surface for
stability.
1. Loosen the coupler by turning the knob
counterclockwise.
Coupler
TO RELOCATE SHOULDER STRAP
CLAMP:
LOOSEN
1. Loosen and remove both clamp screws.
2. Place the upper shoulder strap clamp
over the upper shaft.
3. Position the lower shoulder strap clamp
under the upper shaft and align the upper
and lower clamp screw holes.
TIGHTEN
Knob
2. Remove the shaft cap from attachment (if
present).
3. Position locking/release button of attach-
ment into guide recess of coupler.
4. Push the attachment into the coupler until
the locking/release button snaps into the
primary hole.
houlder
amp
POWERHEAD
END
5. Before using the unit, tighten the knob se-
curely by turning clockwise.
Coupler
Primary Hole
Guide Recess
ATTACHMENT
Lower Shoulder
END
Screws
Strap Clamp
Locking/
Release
Button
Upper
Shaft
Lower
Attachment
4. Insert two screws into the screw holes.
5. Secure shoulder strap clamp by tighten-
ing screws with a hex wrench.
ADJUSTING THE ASSIST HANDLE
WARNING: Make sure the locking/
release button is locked in the primary hole
and the knob is securely tightened before op-
erating the unit. Allattachments aredesigned
to be used in the primary hole.
For assembly of optional attachments (see
list on page 7), refer to the ASSEMBLY sec-
tion of the applicable attachment instruction
manual.
WARNING: When adjusting the assist
handle during pruner use, be sure it remains be-
tween the coupler and the
lower arrow
(closest to coupler) on the safety label to ensure
proper balancing of unit. When adjusting the
assist handle during use of optional attach-
ments, it must be repositioned between the trig-
SHOULDER STRAP ASSEMBLY
ger switch and the
upper arrow (closest to
motor) on the safety label.
WARNING: Proper shoulder strap
adjustments must be made with the motor
completely stopped before using unit.
1. Loosen wing nut on handle.
2. Rotate the handle on the shaft to an up-
right position; retighten wing nut.
10
ATTACHING SHIELD
(for line trimmer attachment)
Shield
Slot
PIVOT
WARNING: The shield must be prop-
erly installed. The shield provides partial protec-
tion from the risk of thrown objects to the opera-
tor and others and is equipped with a line limiter
blade which cuts excess line to the proper
length. The line limiter blade (on underside of
shield) is sharp and can cut you.
Bracket
Line Limiter
Blade
Wing
Nut
For proper orientation of shield, see KNOW
YOUR TRIMMER ATTACHMENT illustration in
OPERATION section.
1. Remove wing nut from shield.
2. Insert bracket into slot as shown.
3. Pivot shield until bolt passes through hole
in bracket.
4. Securely tighten wing nut onto bolt.
OPERATION
KNOW YOUR UNIT
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.
Compare the illustrations with your unit to familiarize yourself with the location of the various controls
and adjustments. Save this manual for future reference.
ndle
Shoulder Strap Clamp
Motor Housing
Line Trimmer
Attachment
Recessed
Plug
Attachment
Hanger
Cord Retainer
Bar oil fill cap
Shield
Chain
Trigger Switch
Bar
Bar nut
RECESSED PLUG
COUPLER
The RECESSED PLUG is where you attach
your extension cord to the unit.
The COUPLER enables optional attach-
ments to be installed on the unit.
CHAIN TENSION
TRIGGER SWITCH
TheTRIGGER SWITCHis used toturn onthe
unit. Squeeze the trigger switchto operate the
unit. Release to stop.
It is normal for a new chain to stretch during
first 15 minutes of operation. You should
check your chain tension frequently. See
CHAIN TENSION in the SERVICE AND AD-
JUSTMENTS section.
SELECT AN EXTENSION CORD
OPERATING INSTRUCTIONS
Use only a voltage supply as specified on
your unit.
Extension Cord Gauge Chart
Length of Cord
Gauge
18 Gauge
16 Gauge
14 Gauge
25 Ft. (7.5 m)
50 Ft. (15 m)
100 Ft. (30 m)
Extension cords are available for this unit.
11
1. Loosen the coupler by turning the knob
counterclockwise.
ATTACH THE EXTENSION
CORD TO YOUR UNIT
Upper Shaft
Makea loop in your extensioncord andattach
the cord as shown. Ensure the plug and cord
are firmly and fully engaged.
Coupler
LOOSEN
Lower
Attachment
Cord Retainer
TIGHTEN
Knob
2. Press and hold the locking/release button.
Locking/Release
Button
Coupler
Lower Attachment
Upper Shaft
Extension Cord
3. While securely holding the motor housing
and upper shaft, pull the attachment
straight out of the coupler.
Recessed Plug on Unit
BEFORE STARTING UNIT
INSTALLING OPTIONAL ATTACH-
Be sure to read the electrical safety information
in the safety rules section of this manual before
you begin. If you do not understand the electrical
safety information do not attempt to use your
unit. Seek help from someone that does under-
stand the information or call the customer assis-
tance help line at 1-800-554-6723.
MENTS
1. Remove the shaft cap from the attach-
ment (if present).
2. Position locking/release button of attach-
ment into guide recess of coupler.
3. Push the attachment into the coupler until
the locking/release button snaps into the
primary hole.
GUIDE BAR AND CHAIN OIL
The bar and chain require lubrication. The chain
oiler provides continuous lubrication to the chain
and guide bar. Lack of oil will quickly ruin the bar
and chain. Too little oil will cause overheating
shown by smoke coming from the chain and/or
discoloration of the bar. The oil output is auto-
matically metered during operation. Always fill
the bar oil tank before and during use as needed
(capacity = 4.6 fl. oz.).
4. Before using the unit, tighten the knob se-
curely by turning clockwise.
Primary Hole
Coupler
Guide Recess
Genuine Poulan bar and chain oil is recom-
mended to protect your unit against exces-
sive wear from heat and friction. Poulan oil
resists high temperature thinning.
Locking/
Attachment
Upper
Shaft
Release
Button
If Poulan bar and chain oil is not available,
use a good grade SAE 30 oil.
WARNING: Make sure the locking/
release button is locked in the primary hole
and the knob is securely tightened before op-
erating the unit.
S Never use waste oil for bar and chain lubri-
cation.
S Always stop the unit before removing theoil
cap.
INSTALLING ATTACHMENT
HANGER
WARNING: Always stop unit anddis-
connect from power source before removing
or installing attachments.
REMOVING PRUNER ATTACHMENT,
LINE TRIMMER ATTACHMENT OR
OTHER OPTIONAL ATTACHMENTS
CAUTION: When removing or installing at-
tachments, place the unit on a flat surface for
stability.
An attachment hanger is provided for storage
when attachment is not in use.
To install hanger on attachment:
1. Remove the shaft cap from the attach-
ment (if present) and discard.
2. Press and hold the locking/release button.
3. Push hanger onto the attachment untilthe
locking/release button snaps into the
hole.
12
the rear branch, damage to the unit may oc-
cur.
Be alert for springback. Watch out for
branches that are bent or under pressure.
Avoid being struck by the branch or the
pruner when the tension in the wood fi-
bers is released.
Keep a clear work area. Frequently clear
branches out of the way to avoid tripping
over them.
Long branches should be removed in
several pieces.
OPERATING INSTRUCTIONS FOR
PRUNER ATTACHMENT
OPERATING POSITION
S
ALWAYS WEAR:
Head
S
S
Protection
Eye
Protection
PRUNING TECHNIQUE
When ready to cut, squeeze trigger switch
and allow unit to reachfull speed. Apply alight
cutting pressure. DO NOT use back and forth
sawing action.
Long Pants
Heavy Shoes
DANGER: Do not extend arms above
shoulders while pruning. Do not stand be-
neath branch being cut.
Second cut
Third cut
WARNING: Always wear head, eye,
hearing, foot and body protection to reduce
the risk of injury when operating this unit.
When operating unit, clip shoulder strap onto
clamp, stand as shown and check for the fol-
lowing:
S Extend your left arm and hold assist handle
with your left hand.
S Holdtrigger handle with your right hand with
finger on trigger switch.
Collar
First cut
Pruning technique
S Keep motor end below waist level.
S Keep shoulder strap pad centered on your
left shoulder and danger sign centered on
your back.
1. Make the first cut 6 inches (15 cm) from
the tree trunk on the bottom of the limb.
Use top of guide bar to make this cut. Cut
1/3 through the diameter of the limb.
NOTE: When making the second and third
cuts, rest the foot of the pruner against the
tree limb that is being cut to prevent whipping
of the branch.
S Maintain full weight of tool on your left
shoulder.
Always release the trigger switch as soon as
the cut is completed, allowing the motor to
stop. Keep the cord away from the cutting
area. Position cord so it will not be caught on
branches and the like during cutting.
PRUNING
WARNING: Be alert for and guard
against kickback. Do not allow the moving
chain to contact any other branches or ob-
jects at the nose of the guide bar when prun-
ing. Allowing such contact can result in seri-
ous injury.
IMPORTANT POINTS
Foot
S
Work slowly, keeping both hands firmly
gripped on the pruner. Maintain secure
footing and balance.
S
S
Plan cut carefully. Check directionbranch
will fall.
Watch out for springpoles. Springpoles are
small size limbs which can catch the chain
and whip toward you or pull you off balance.
Use extreme caution when cutting small
size limbs or slender material.
2. Next, move 2 -- 4 inches (5 -- 10 cm) far-
ther out on the limb and make a second
cut all the way through the limb.
3. Then, make a final cut leaving a 1 -- 2 inch
(2.5 -- 5 cm) collar from the trunk of the
tree to avoid damage to the tree.
S
Watch out for branches immediately behind
the branch being pruned. If the chain hits
13
OPERATING INSTRUCTIONS FOR
TRIMMER ATTACHMENT
OPERATING POSITION
CUTTING METHODS
WARNING: Use minimum speed and
do not crowd the line when cutting around
hard objects (rock, gravel, fence posts, etc.),
whichcandamage the trimmer head, become
entangled in the line, or be thrown causing a
serious hazard.
ALWAYS WEAR:
Eye Protection
S The tip of the line does the cutting. You will
achieve the best performance and mini-
mum line wear by not crowding the line into
the cutting area. The right and wrong ways
are shown below.
Long Pants
Tip of the Line
Line Crowded Into
Work Area
Heavy Shoes
Does The Cutting
Cut from your right to your left.
WARNING: Always wear eye protec-
tion. Never lean over the trimmer head.
Rocks or debris can ricochet or be thrown into
eyes and face and cause blindness or other
serious injury.
Right
Wrong
S The line will easily remove grass and
weeds fromaround walls, fences, trees and
flower beds, but it also can cut the tender
bark of trees or shrubs and scar fences.
S For trimming or scalping, use less than full
throttle to increase line life and decrease head
wear, especially:
When operating unit, stand as shown and check
for the following:
S Wear eye protection and heavy clothing.
S Hold trigger handle with right hand and as-
sist handle with left hand.
S Keep unit below waist level.
S During light duty cutting.
S Cut from your right to your left to ensure de-
bris is thrownaway fromyou. Without bend-
ing over, keep line near and parallel to the
ground and not crowded into material being
cut.
S Near objects around which the line can
wrap such as small posts, trees or fence
wire.
S For mowing or sweeping, use full throttle for
a good clean job.
TRIMMER LINE ADVANCE
TRIMMING -- Hold the bottom of the trimmer
head about 3 inches (8 cm) above the ground
and at an angle. Allow only the tip of the line to
make contact. Do not force trimmer line into
work area.
The trimmer line will advance approximately 2
inches (5 cm) each time the bottom of the
trimmer head is tapped on the ground with the
engine running at full throttle.
The most efficient line length is the maximum
length allowed by the line limiter.
Trimming
Always keep the shield in place when the tool
is being operated.
To advance line:
S Operate the engine/motor at full throttle.
S Hold the trimmer head parallel to andabove
the grassy area.
3 inches (8 cm)
above ground
S Tap the bottom of the trimmer head lightly on
the ground one time. Approximately 2 inches
(5 cm) of line will be advanced with each tap.
Always tap the trimmer head on a grassy area.
Tapping on surfaces such as concrete or as-
phalt can cause excessive wear to the trimmer
head. If the line is worn down to 2 inches (5 cm)
or less, more than one tap will be required to ob-
tain the most efficient line length.
SCALPING -- The scalping technique re-
moves unwanted vegetation down to the
ground. Hold the bottom of the trimmer head
about 3 in. (8 cm) above the ground and at an
angle. Allow the tip of the line to strike the
ground around trees, posts, monuments, etc.
This technique increases line wear.
Scalping
WARNING: Use only 0.080” (2 mm)
diameter line. Other sizes of line will not ad-
vance properly and can cause serious injury.
Do not use other materials such as wire,
string, rope, etc. Wire can break off during
cutting and become a dangerous missile that
can cause serious injury.
MOWING -- Your trimmer is ideal for mowing
in places conventional lawn mowers cannot
reach. In the mowing position, keep the line
parallel to the ground. Avoid pressing the
head into the ground as this can scalp the
ground and damage the tool.
14
the surfaces being swept and move the tool
from side to side.
Mowing
Swee
SWEEPING -- The fanning action of the rotat-
ing line can be used for a quick and easy
clean up. Keep the line parallel to and above
MAINTENANCE
WARNING: Disconnect unit from
power source before performing maintenance.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Bar clamp nut
Adjusting Screw
Bar clamp nut
S Chain
3. Turn adjusting screw clockwise until
chain solidly contacts bottom of guide bar
rail. Then, turn adjusting screw an addi-
tional 1/4 turn.
S Bar adjusting screw
S Housing screws
S Assist handle screw
S Debris shield
CHECK FOR DAMAGED OR
WORN PARTS
Adjusting Screw -- 1/4 Turn
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S Trigger switch -- Ensure trigger switch func-
tions properly by pressingand releasing the
trigger switch. Make sure motor starts and
stops.
4. Using bar tool, roll chain around guide bar to
ensure all links are in bar groove.
5. Lift up tip of guide bar to check for sag.
Release tip of guide bar, then turn adjust-
ing screw 1/4 turn clockwise. Repeat until
sag does not exist.
S Oil tank -- Discontinue use of unit if oil tank
shows signs of damage or leaks.
6. While lifting tip of guide bar, tighten bar
clamp nut securely with the bar tool.
INSPECT AND CLEAN UNIT AND
LABELS
S
After each use, inspect complete unit for
loose or damaged parts. Clean the unit
and labels using a damp cloth.
S
Wipe off unit with a clean dry cloth.
CHECK CHAIN TENSION
WARNING: Wear protective gloves
when handling chain. The chain is sharp and
can cut you even when it is not moving. Make
chain adjustments with lower end supported.
Chain tension is very important. Chains
stretch duringuse. This is especially true dur-
ing the first few times you use your pruner. Al-
ways check chain tension each time you use
your unit.
1. Use the screwdriver end of the chain ad-
justment tool (bar tool) to move chain
around guide bar to ensure kinks do not
exist. The chain should rotate freely.
7. Use the screwdriver end of the bar tool to
move chain around guide bar.
8. If chain does not rotate, it is too tight.
Slightly loosen bar clamp nut and loosen
chain by turning the adjusting screw 1/4
turn counterclockwise. Retighten bar
clamp nut.
9. If chain is too loose, it will sag below the
guide bar and needs to be tightened fol-
lowing above procedure.
WARNING: DO NOT operate the
pruner if the chain is loose. If the pruner is oper-
ated with a loose chain, the chain could jump off
the guide bar and result in serious injury.
Chain Adjustment T
ide
Bar
CHECK CHAIN SHARPNESS
A sharp chain makes wood chips. A dull chain
makes a sawdust powder and cuts slowly.
See CHAIN SHARPENING in the SERVICE
AND ADJUSTMENTS section.
2. Loosen bar clamp nut until it is finger tight
against the bar clamp.
15
S Burring of guide bar rails is a normal
process of rail wear. Remove these burrs
with a flat file.
BAR MAINTENANCE
If your pruner cuts to one side, has to be
forced through the cut, or been runwith an im-
proper amount of bar lubrication it may be
necessary to service your bar. A worn bar will
damage your chain and make cutting difficult.
After each use, with unit disconnected from
power source, clean all sawdust from the
guide bar and sprocket hole.
S When rail top is uneven, use a flat file to re-
store square edges and sides.
File Rail Edges
and Sides
Square
To maintain guide bar:
Worn Groove
Correct Groove
S Disconnect pruner from power source.
S Loosen and remove bar clamp nut and
chain brake. Remove bar and chain from
pruner.
Replace guide bar when the groove is worn, the
guide bar is bent or cracked, or when excess
heating or burring of the rails occurs. If replace-
ment is necessary, use only the guide bar speci-
fied for your pruner in the repair parts list.
S Clean the oil holes and bar groove after
each 5 hours of operation.
LUBRICATION
Bar Oil
Fill Cap
Remove Sawdust From
Guide Bar Groove
Oil Holes
S See GUIDE BAR AND CHAIN OIL under
the OPERATION section.
SERVICE AND ADJUSTMENTS
File Holder
WARNING: Disconnect unit from
power source before performing service or
making adjustments.
File
90˚
CHAIN SHARPENING
Cutter
Improper chain sharpening techniques and/or
depth gauge maintenance will increase the
chance of kickback which can result in serious
injury.Wear protective gloves when handling
chain. The chain is sharp and can cut you even
when it is not moving.
Depth Gauge
S
Align the 30˚ file holder marks parallel
with the bar and to the center of the
chain.
Cutter
Conditions which indicate the need for chain
sharpening:
S Reduction insize of wood chips. The size of
the wood chip will decrease as the chain
gets duller until it becomes more like apow-
der than a chip. Note that dead or rotted
wood will not produce a good chip.
S Saw cuts to one side or at an angle.
S Saw has to be forced through the cut.
Tools required:
S 3/16 inch (4,5 mm) diameter round file and
file holder
S Flat file
S Depth gauge tool
30˚
File Holder Line
Cutter
S
Sharpen cutters on one side of the chain
first. File from the inside of each cutter to
the outside. Then, turn the chain saw
around and repeat the process for the
other side of the chain.
File on the forward stroke only. Use 2
or 3 strokes per cutting edge.
Keep all cutters the same length when
filing.
File enough to remove any damage to
cutting edges (side plate and top plate
of cutter).
S
S
S
TO SHARPEN CHAIN:
1. Disconnect pruner from power source.
2. Check chain for proper tension. Adjust
chain tension if necessary. See CHECK
CHAIN TENSION section.
Remove Damage
All Cutters
Same Length
3. Sharpen cutters.
S
To sharpen the cutters, position the
file holder level (90˚) so that it rests on
the top edges of the cutter and depth
gauge.
Top Plate
Side Plate
NOTE: The chain has both left and
right hand cutters.
S
File chain to meet the specifications
as shown.
16
4. Turn adjusting screw by hand counter-
clockwise until adjusting pin just touches
the stop.
60˚
75˚
5. Slide guide bar behind sprocket until
guide bar stops against sprocket.
6. Remove the old chain.
30˚
7. Carefully remove new chain from pack-
age. Hold chain with the drive links as
shown.
Hook Angle
0.025 inch
(0.65 mm)
Cutter
Tip of
Bar
Rounded
Corner
Drivelink
Right
Too Much Hook Angle
Squared Off
Corner
CUTTERS MUST FACE IN
DIRECTION OF ROTATION
Depth Gauge
Cutters
Wrong
WARNING: Maintain the proper hook
angle according to the manufacturer’s specifica-
tions for the chain you are using. Improper hook
angle will increase the chance of kickback
which can result in serious injury.
Drive Links
4. Check and lower depth gauges.
File
Depth Gauge Tool
Depth Gauge
S
S
Place gauge tool on cutter.
If the depth gauge is higher than the
depth gauge tool, file it level to the top of
the depth gauge tool.
S
Maintainroundedfront corner of depth
gauge with a flat file.
8. Place chainover sprocket, fitting the drive
links in the sprocket.
9. Fit bottom of drive links between the teeth in
the sprocket in the nose of the guide bar.
10. Fit chain drive links into bar groove.
11. Pull guide bar forward until chain is snug
in guide bar groove. Ensure all drive links
are in the bar groove.
NOTE: The very top of the depth
gauge should be flat with the front half
rounded off with a flat file.
If you require further assistance or are unsure
about performing this procedure, contact your
authorized service dealer or call our customer
assistance help line at 1--800--554--6723.
12. Now, install bar clamp making sure the
adjusting pin is positioned in the lower
hole in the guide bar.
CHAIN REPLACEMENT
WARNING: Wear protective gloves
when handling chain. The chain is sharp and
can cut you even when it is not moving.
It is normal for a new chain to stretch during the
first 15 minutes of operation. You should re-
check your chain tension frequently and adjust
the chain tension as required. See CHAIN TEN-
SION section.
Lower
Hole
Adjusting Pin
Replace the old chain when it becomes worn or
damaged. Use only the Low-Kickback replace-
ment chain specified in the repair parts list.
Guide Bar
TO REPLACE CHAIN:
13. Install bar clamp nut and finger tighten
only. Do not tighten any further at this
point. Proceed to the CHAIN ADJUST-
MENT section.
1. Disconnect pruner from power source.
2. Remove bar clamp nut.
3. Remove bar clamp.
17
CHAIN ADJUSTMENT
See CHECK CHAIN TENSION in MAINTE-
NANCE section.
Line exit holes
Line in Notch
REPLACING THE LINE
(for line trimmer attachment)
1. Remove spool by firmly pulling on tapbut-
ton.
2. Clean entire surface of hub and spool.
3. Replace with a pre-wound spool, or cut two
lengths of 12-1/2 feet of 0.080″ (2 mm) di-
ameter Poulan brand line.
5. Wind the line evenly and tightly onto the
spool. Wind in the direction of the arrows
found on the spool.
6. Push the lines into the notches, leaving 3
to 5 inches (7 -- 12 cm) unwound.
WARNING: Never use wire, rope,
string, etc., which can break off and becomea
dangerous missile.
4. Insert ends of the lines about 1/2 inch (1
cm) into the small holes on the inside of
spool.
7. Insert the lines into thethe exit holes inthe
hub as shown in the illustration.
8. Align the notches with the line exit holes.
9. Push spool into hub until it snaps into place.
10. Pull the lines extending outside of the hub
to release the lines from the notches.
Spool
Small
Holes
USER REPLACEABLE SERVICE PARTS
REPLACEMENT PART
Assist handle
Bolt carriage, 1/4-20
Wing nut
Bar
Chain
Hex nut
Oil cap
Bar adjusting screw/pin kit
Spool with 0.080″ trimmer line
Shield assembly
PART NUMBER
530057546
530015786
530016152
530044908
952051549
530015917
530053072
530069110
952711616
530071964--01
STORAGE
SEASONAL STORAGE
Prepare your unit for storage at the end of the
season or if it will not be used for 30 days or
more.
WARNING: Perform the following
steps after each use.
S Stop the unit and disconnect the power
If your unit is to be stored for a period of time:
S Clean it thoroughly before lengthy storage.
S Store in a clean dry area.
source when not in use.
S Carry the unit with motor stopped.
S Allow motor to cool before storing or trans-
porting.
S Lightly oil external metal surfaces and guide
bar.
S Oil the chain and wrap it in heavy paper or
cloth.
S Store unit and extension cord indoors in a
high, dry place out of the reach of children.
Store unit unplugged.
S Store unit with all guards in place and position
unit so that any sharp object cannot acciden-
tally cause injury.
18
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect from the power source before per-
forming all of the recommendedremedies below except remedies that requireunit tobe
operating.
TROUBLE
CAUSE
REMEDY
1. Chain tension incorrect.
1. See “Check Chain Tension” in
Chain does
not move
when trigger
switch is
Maintenance section.
2. Guide bar rails pinched.
3. Trigger switch failure.
2. Repair or replace.
3. Contact an authorized service
dealer.
engaged.
4. Circuit breaker tripped/
fuse failure.
4. Reset circuit breaker or replace fuse.
Chain clatters
or cuts
roughly.
1. Chain tension incorrect.
1. See “Check Chain Tension” in
Maintenance Section.
2. Cutters damaged.
2. Contact an authorized service
dealer.
3. Chain worn.
3. Resharpen or replace chain.
4. See “Chain Sharpening” in
Service and Adjustments section.
4. Cutters dull, improperly
sharpened, or depth
gauges too high.
5. Sprocket worn.
5. Contact an authorized service
dealer.
Chain stops
during cut.
1. Chain cutter tops not
filed flat.
2. Guide bar burred or
bent; rails uneven.
1. See “Chain Sharpening” in
Service and Adjustments section.
2. Repair or replace guide bar.
Oil inadequate 1. Oil tank empty.
1. Fill oil tank.
2. Oil outlet clogged.
2. Contact an authorized service
dealer.
for bar and
chain lubrica-
tion.
3. Guide bar oil hole
blocked.
3. Remove bar and clean.
Chain cuts at
an angle.
1. Cutters damaged on
1. See “Chain Sharpening” in
Service and Adjustments section.
2. See “Chain Sharpening” in
Service and Adjustments section.
3. Replace guide bar.
one side.
2. Chain dull on one side.
3. Guide bar bent or worn.
Trimmer head
stops under a
load or does
not turn when
switch is
1. Crowding trimmer line
against material being
cut.
2. Electrical failure.
3. Thrown circuit breaker.
4. Debris stopping head.
1. Allow tip of line to do the cutting.
2. Contact your authorized service dealer.
3. Check Breaker Box.
4. Remove debris.
pressed.
1. Line improperly routed
in head.
1. Check line routing.
Line does not
advance or
breaks while
cutting.
2. Line improperly
wound into spool.
3. Incorrect line size
4. Not enough line
outside of head.
2. Rewind line tightly and evenly.
3. Use only 0.080 inch (2 mm) dia. line.
4. Remove cover and pull 4 inches
(10 cm) of line out of head.
5. Clean unit.
5. Dirt buildup on unit.
Line welds
onto spool.
1. Line size is incorrect.
2. Incorrect spool.
3. Line is being crowded
against material being cut.
1. Use only 0.080 inch (2 mm) dia. line.
2. Replace with correct spool.
3. Cut with tip of line fully extended.
Line releases 1. Line improperly
1. Check line routing.
2. Replace spool.
routed in head.
continuously.
2. Spool damaged.
19
TROUBLESHOOTING TABLE (continued)
TROUBLE
CAUSE
REMEDY
1. Check line routing.
Line usage is
1. Line improperly routed
excessive.
in head.
2. Line size is incorrect.
3. Crowding line against
material being cut.
2. Replace spool.
3. Cut with tip of line fully extended.
4. Spool worn or damaged. 4. Replace spool.
1. Too little line outside
of head.
2. Line size incorrect.
Line pulls back
into head.
1. Remove cover and pull 4 inches
(10 cm) of line outside of head.
2. Use only 0.080 inch (2 mm) dia. line.
LIMITED WARRANTY
Poulan, a division of Husqvarna Consumer
Outdoor Products N.A., Inc., warrants to the
original consumer purchaser that each new
Poulan brand electric or cordless product is
free from defects in material and workmanship
and agrees to repair or replace under this war-
ranty any defective Poulan brand electric prod-
uct within two (2) years from the original date of
purchase.
If your Poulan brand electric or cordless prod-
uct should fail within the limited warranty period,
you may return it in complete condition, prepaid,
with proof of purchase to the dealer from whom
it was purchased for repair or replacement at the
option of Poulan.
Giving the model number, serial number and
date of purchase of your product and the name
and address of the authorized dealer from
whom it was purchased.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT
APPLY TO YOU.
This is a limited warranty within the meaning
of that term as defined in the Magnuson--
Moss Act of 1975.
The policy of Poulan is to continuously improve
its products. Therefore, Poulan reserves the
right to change, modify, or discontinue models,
designs, specifications, and accessories of all
products at any time without notice or obligation
to any purchaser.
This warranty is not transferableand does not
cover damage or liability caused by improper
handling, improper maintenance or alteration,
or the use of accessories and/or attachments
not specifically recommended by Poulan for
this product. This warranty does not cover
parts that will wear and require replacement
with reasonable use during the warranty peri-
od. This warranty does not cover pre--deliv-
ery setup or normal adjustments explained in
the instruction manual.
Should you have any unanswered questions
regarding this warranty, please contact:
Poulan, a division of Husqvarna Consumer
Outdoor Products N.A., Inc.
7349 Statesville Road
Charlotte, NC 28269
1--800--554--6723
In Canada, contact:
Poulan
850 Matheson Blvd. West
Mississauga, Ontario L5V 0B4
20
|